Generated by kicad-footprint-generator · KiCad file format 20260206
MAX9947ETE+T
Maxim Integrated · RF Transceiver ICs · WQFN-16-EP(3x3)
MAX9947ETE+T from Maxim Integrated, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNCOUT | output | Open-drain sync output that provides the 8.704MHz clock to synchronize other devices, with VOL of 0.4V max at 3.3mA source, and a 1kΩ pullup to VCC is required on a master device. |
| 2 | TXIN | input | Digital signal input for the OOK transmit data, with logic-high threshold of 0.7 x VL and logic-low threshold of 0.3 x VL. |
| 3 | VL | power_in | Logic supply voltage, specified from 1.6V to 5.5V and independent of VCC. |
| 4 | RXOUT | output | Digital receive data output referenced to VL, with VOH of 0.9 x VL min and VOL of 0.1 x VL max at 3.3mA. |
| 5 | DIR | output | Direction output that is asserted high when the data stream is seen at the receiver (RXIN), used to drive the DE and RE_ of an RS-485 transceiver, with logic levels referenced to VL. |
| 6 | DIRMD2 | input | Duration mode select input 2 that, together with DIRMD1, sets the unity bit time (00 = 9.6kbps, 01 = 38.4kbps, 10 = 115.2kbps, 11 not used), internally pulled down with logic thresholds of 0.7 x VL and 0.3 x VL. |
| 7 | DIRMD1 | input | Duration mode select input 1 that, together with DIRMD2, sets the unity bit time (00 = 9.6kbps, 01 = 38.4kbps, 10 = 115.2kbps, 11 not used), internally pulled down with logic thresholds of 0.7 x VL and 0.3 x VL. |
| 8 | GND | power_in | Ground connection for the device. |
| 9 | RES | passive | External resistor connection that sets the TXOUT output power level, with the voltage at RES required to be between 0.84V and 1.5V. |
| 10 | BIAS | passive | Output bias reference used with RES to set the output power level, which must be decoupled with 1µF to GND. |
| 11 | RXIN | input | OOK-modulated receive input at 2.176MHz with a maximum input of +5dBm (1.12VP-P) into 50Ω and a receiver threshold of -15dBm. |
| 12 | TXOUT | output | OOK-modulated transmit output biased at 1.5V, AC-coupled to the feeder cable, with short-circuit current protected to ±200mA to GND or VCC. |
| 13 | VCC | power_in | Analog supply voltage, specified from 3.0V to 5.5V. |
| 14 | XTAL1 | input | External crystal input that accepts an 8.704MHz (±30ppm) clock for external synchronization, with VIH of 0.7 x VCC and VIL of 0.3 x VCC. |
| 15 | XTAL2 | input | External crystal terminal that must be connected to GND to configure the device as a slave that accepts an external clock on XTAL1. |
| 16 | GND | power_in | Ground connection for the device. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | WQFN-16-EP(3x3) |
| Category | RF & Radio |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 3 | 5.5 | V | Guaranteed by PSRR | 2 | |
| Logic Supply Voltage | VL | 1.6 | 5.5 | V | Guaranteed by logic supply current | 2 | |
| Supply Current | ICC | 23 | 35 | mA | TA ≤ 85°C | 2 | |
| Supply Current | ICC | 27 | 40 | mA | TA > 85°C | 2 | |
| Logic Supply Current | IL | 138 | 380 | µA | VTXIN = 3.3V | 2 | |
| Receiver Power-Supply Rejection Ratio | PSRR | 49 | 60 | dB | 3.0V ≤ VCC ≤ 5.5V, VTXIN = 3.3V (Note 3) | 2 | |
| Output Power-Supply Rejection Ratio | PSRR | 49 | 60 | dB | 3.0V ≤ VCC ≤ 5.5V, VTXIN = 0V (Note 4) | 2 | |
| Input Leakage Current | IIH, IIL | -1 | 1 | µA | TXIN shorted to GND or VL | 2 | |
| Input Leakage Current | IIH, IIL | -1 | µA | DIRMD1, DIRMD2 shorted to GND | 2 | ||
| Input Leakage Current | IIH, IIL | 60 | µA | DIRMD1, DIRMD2 shorted to VL | 2 | ||
| Input High Leakage Current | IXTAL1_IH | 10 | µA | 3 | |||
| Input Low Leakage Current | IXTAL1_IL | -10 | µA | 3 | |||
| Output Low Voltage | VSYNCOUT_OL | 0.4 | V | SYNCOUT source 3.3mA | 3 | ||
| Passband | fPB_L, fPB_H | 1.1 | 4.17 | MHz | Input amplitude 1.12VP-P (the input carrier is recognized) | 3 | |
| Extra Carrier Receiver Immunity | fIM1_L, fIM1_H | 1.1 | 4.17 | MHz | 2.176MHz carrier amplitude (112.4mVP-P ±3dB), extra carrier amplitude 0.8VP-P, VDIRMD1 = VDIRMD2 = 0V (9.6kbps) | 3 | |
| Input Voltage Range | VIN | 1.12 | VP-P | VCC = 3.0V to 5.5V, fRXIN = 2.176MHz | 3 | ||
| Equivalent Input Power Range | PIN | 5 | dBm | VCC = 3.0V to 5.5V, fRXIN = 2.176MHz | 3 | ||
| Input Impedance | ZIN | 11 | 18 | kΩ | f = fO, TA ≤ 85°C | 3 | |
| Input Impedance | ZIN | 9 | 18 | kΩ | f = fO, TA > 85°C | 3 | |
| Threshold Voltage Range | VTH | -18 | -15 | -12 | dBm | fRXIN = 2.176MHz | 3 |
| Threshold Voltage Range | VTH | 79.72 | 112.4 | 158.48 | mVP-P | fRXIN = 2.176MHz | 3 |
| Output Frequency Variation | ΔfO | -100 | 100 | ppm | (Note 5) | 3 | |
| Output On Level at TXOUT | VOUT | 11.1 | 12 | dBm | VRES = 1.5V (maximum) | 3 | |
| Output On Level at TXOUT | VOUT | 2.24 | 2.52 | VP-P | VRES = 1.5V (maximum) | 3 | |
| Output On Level at TXOUT | VOUT | 5.38 | 6.28 | dBm | VRES = 0.7V (minimum) | 3 | |
| Output On Level at TXOUT | VOUT | 1.17 | 1.3 | VP-P | VRES = 0.7V (minimum) | 3 | |
| Output Off Power Level at TXOUT | POUT | -40 | dBm | OOK off level | 3 | ||
| TXOUT Short-Circuit Protection | ISC | -200 | 200 | mA | Short to GND or VCC, guaranteed over VCC range | 3 | |
| Receiver Propagation Delay | tRX | 8.9 | 11 | µs | RXIN to RXOUT, VDIRMD1 = VDIRMD2 = 0V | 4 | |
| Receiver Propagation Delay | tRX | 5.5 | 11 | µs | RXIN to RXOUT, VDIRMD1 = 3.3V, VDIRMD2 = 0V (38.4kbps); VDIRMD1 = 0V, VDIRMD2 = 3.3V (115.2kbps) | 4 | |
| Receiver Output Rise and Fall Time | tR, tF | 20 | ns | 10% to 90%, RL = 1kΩ, CL = 10pF | 4 | ||
| Receiver Output Data Duty-Cycle Variation | ΔDC | -10 | -7.5 | 10 | % | RXIN = 0dBm; RXIN fed by OOK 2.176MHz sinusoid, 50% duty cycle (Note 9) | 4 |
| Receiver Output Data Duty-Cycle Variation | ΔDC | -10 | 2 | 10 | % | RXIN = -10dBm; RXIN fed by OOK 2.176MHz sinusoid, 50% duty cycle (Note 9) | 4 |
| VCC to GND | VCC | -0.3 | 6 | V | 2 | ||
| VL to GND | VL | -0.3 | 6 | V | 2 | ||
| RXIN, XTAL1, XTAL2, SYNCOUT, RES to GND | -0.3 | 6 | V | 2 | |||
| All Other Pins Max In/Out Current | -20 | 20 | mA | 2 | |||
| Operating Temperature Range | -40 | 105 | °C | 2 | |||
| Junction Temperature | 150 | °C | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (soldering, 10s) | 300 | °C | soldering, 10s | 2 | |||
| Soldering Temperature (reflow) | 260 | °C | reflow | 2 | |||
| Junction-to-Case Thermal Resistance | θJC | 40 | °C/W | TQFN, JESD51-7 four-layer board | 2 | ||
| Output Frequency | fO | 2.176 | MHz | 3 | |||
| Amplifier Gain Bandwidth | GBW | 54 | MHz | 3 | |||
| Output Impedance | ZOUT | 0.03 | Ω | DC | 3 | ||
| Output Impedance | ZOUT | 2.5 | Ω | fSW = 10MHz | 3 | ||
| Transmitter Propagation Delay | tTX | 5 | µs | TXIN to TXOUT | 4 | ||
| DIR to RXOUT Delay | tDIR, SKEW | 270 | ns | (Note 8) | 4 | ||
| Direction Duration High | tDIR, HIGH | 1667 | µs | VDIRMD1 = VDIRMD2 = 0V (9.6kbps) | 4 | ||
| Direction Duration High | tDIR, HIGH | 417 | µs | VDIRMD1 = 3.3V, VDIRMD2 = 0V (38.4kbps) | 4 | ||
| Direction Duration High | tDIR, HIGH | 137 | µs | VDIRMD1 = 0V, VDIRMD2 = 3.3V (115.2kbps) | 4 |
CAD (KiCad official)
- Symbol:
MAX9947ETE+T - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
max9947ete-t-etched.step/max9947ete-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max9947ete-t.step/max9947ete-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Maxim Integrated datasheet (17 pp, sha256
56963b82445bcb7d, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).