Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX9947ETE+T

Maxim Integrated · RF Transceiver ICs · WQFN-16-EP(3x3)

MAX9947ETE+T from Maxim Integrated, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNCOUT output Open-drain sync output that provides the 8.704MHz clock to synchronize other devices, with VOL of 0.4V max at 3.3mA source, and a 1kΩ pullup to VCC is required on a master device.
2 TXIN input Digital signal input for the OOK transmit data, with logic-high threshold of 0.7 x VL and logic-low threshold of 0.3 x VL.
3 VL power_in Logic supply voltage, specified from 1.6V to 5.5V and independent of VCC.
4 RXOUT output Digital receive data output referenced to VL, with VOH of 0.9 x VL min and VOL of 0.1 x VL max at 3.3mA.
5 DIR output Direction output that is asserted high when the data stream is seen at the receiver (RXIN), used to drive the DE and RE_ of an RS-485 transceiver, with logic levels referenced to VL.
6 DIRMD2 input Duration mode select input 2 that, together with DIRMD1, sets the unity bit time (00 = 9.6kbps, 01 = 38.4kbps, 10 = 115.2kbps, 11 not used), internally pulled down with logic thresholds of 0.7 x VL and 0.3 x VL.
7 DIRMD1 input Duration mode select input 1 that, together with DIRMD2, sets the unity bit time (00 = 9.6kbps, 01 = 38.4kbps, 10 = 115.2kbps, 11 not used), internally pulled down with logic thresholds of 0.7 x VL and 0.3 x VL.
8 GND power_in Ground connection for the device.
9 RES passive External resistor connection that sets the TXOUT output power level, with the voltage at RES required to be between 0.84V and 1.5V.
10 BIAS passive Output bias reference used with RES to set the output power level, which must be decoupled with 1µF to GND.
11 RXIN input OOK-modulated receive input at 2.176MHz with a maximum input of +5dBm (1.12VP-P) into 50Ω and a receiver threshold of -15dBm.
12 TXOUT output OOK-modulated transmit output biased at 1.5V, AC-coupled to the feeder cable, with short-circuit current protected to ±200mA to GND or VCC.
13 VCC power_in Analog supply voltage, specified from 3.0V to 5.5V.
14 XTAL1 input External crystal input that accepts an 8.704MHz (±30ppm) clock for external synchronization, with VIH of 0.7 x VCC and VIL of 0.3 x VCC.
15 XTAL2 input External crystal terminal that must be connected to GND to configure the device as a slave that accepts an external clock on XTAL1.
16 GND power_in Ground connection for the device.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Maxim Integrated
Package WQFN-16-EP(3x3)
Category RF & Radio
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC 3 5.5 V Guaranteed by PSRR 2
Logic Supply Voltage VL 1.6 5.5 V Guaranteed by logic supply current 2
Supply Current ICC 23 35 mA TA ≤ 85°C 2
Supply Current ICC 27 40 mA TA > 85°C 2
Logic Supply Current IL 138 380 µA VTXIN = 3.3V 2
Receiver Power-Supply Rejection Ratio PSRR 49 60 dB 3.0V ≤ VCC ≤ 5.5V, VTXIN = 3.3V (Note 3) 2
Output Power-Supply Rejection Ratio PSRR 49 60 dB 3.0V ≤ VCC ≤ 5.5V, VTXIN = 0V (Note 4) 2
Input Leakage Current IIH, IIL -1 1 µA TXIN shorted to GND or VL 2
Input Leakage Current IIH, IIL -1 µA DIRMD1, DIRMD2 shorted to GND 2
Input Leakage Current IIH, IIL 60 µA DIRMD1, DIRMD2 shorted to VL 2
Input High Leakage Current IXTAL1_IH 10 µA 3
Input Low Leakage Current IXTAL1_IL -10 µA 3
Output Low Voltage VSYNCOUT_OL 0.4 V SYNCOUT source 3.3mA 3
Passband fPB_L, fPB_H 1.1 4.17 MHz Input amplitude 1.12VP-P (the input carrier is recognized) 3
Extra Carrier Receiver Immunity fIM1_L, fIM1_H 1.1 4.17 MHz 2.176MHz carrier amplitude (112.4mVP-P ±3dB), extra carrier amplitude 0.8VP-P, VDIRMD1 = VDIRMD2 = 0V (9.6kbps) 3
Input Voltage Range VIN 1.12 VP-P VCC = 3.0V to 5.5V, fRXIN = 2.176MHz 3
Equivalent Input Power Range PIN 5 dBm VCC = 3.0V to 5.5V, fRXIN = 2.176MHz 3
Input Impedance ZIN 11 18 kΩ f = fO, TA ≤ 85°C 3
Input Impedance ZIN 9 18 kΩ f = fO, TA > 85°C 3
Threshold Voltage Range VTH -18 -15 -12 dBm fRXIN = 2.176MHz 3
Threshold Voltage Range VTH 79.72 112.4 158.48 mVP-P fRXIN = 2.176MHz 3
Output Frequency Variation ΔfO -100 100 ppm (Note 5) 3
Output On Level at TXOUT VOUT 11.1 12 dBm VRES = 1.5V (maximum) 3
Output On Level at TXOUT VOUT 2.24 2.52 VP-P VRES = 1.5V (maximum) 3
Output On Level at TXOUT VOUT 5.38 6.28 dBm VRES = 0.7V (minimum) 3
Output On Level at TXOUT VOUT 1.17 1.3 VP-P VRES = 0.7V (minimum) 3
Output Off Power Level at TXOUT POUT -40 dBm OOK off level 3
TXOUT Short-Circuit Protection ISC -200 200 mA Short to GND or VCC, guaranteed over VCC range 3
Receiver Propagation Delay tRX 8.9 11 µs RXIN to RXOUT, VDIRMD1 = VDIRMD2 = 0V 4
Receiver Propagation Delay tRX 5.5 11 µs RXIN to RXOUT, VDIRMD1 = 3.3V, VDIRMD2 = 0V (38.4kbps); VDIRMD1 = 0V, VDIRMD2 = 3.3V (115.2kbps) 4
Receiver Output Rise and Fall Time tR, tF 20 ns 10% to 90%, RL = 1kΩ, CL = 10pF 4
Receiver Output Data Duty-Cycle Variation ΔDC -10 -7.5 10 % RXIN = 0dBm; RXIN fed by OOK 2.176MHz sinusoid, 50% duty cycle (Note 9) 4
Receiver Output Data Duty-Cycle Variation ΔDC -10 2 10 % RXIN = -10dBm; RXIN fed by OOK 2.176MHz sinusoid, 50% duty cycle (Note 9) 4
VCC to GND VCC -0.3 6 V 2
VL to GND VL -0.3 6 V 2
RXIN, XTAL1, XTAL2, SYNCOUT, RES to GND -0.3 6 V 2
All Other Pins Max In/Out Current -20 20 mA 2
Operating Temperature Range -40 105 °C 2
Junction Temperature 150 °C 2
Storage Temperature Range -65 150 °C 2
Lead Temperature (soldering, 10s) 300 °C soldering, 10s 2
Soldering Temperature (reflow) 260 °C reflow 2
Junction-to-Case Thermal Resistance θJC 40 °C/W TQFN, JESD51-7 four-layer board 2
Output Frequency fO 2.176 MHz 3
Amplifier Gain Bandwidth GBW 54 MHz 3
Output Impedance ZOUT 0.03 Ω DC 3
Output Impedance ZOUT 2.5 Ω fSW = 10MHz 3
Transmitter Propagation Delay tTX 5 µs TXIN to TXOUT 4
DIR to RXOUT Delay tDIR, SKEW 270 ns (Note 8) 4
Direction Duration High tDIR, HIGH 1667 µs VDIRMD1 = VDIRMD2 = 0V (9.6kbps) 4
Direction Duration High tDIR, HIGH 417 µs VDIRMD1 = 3.3V, VDIRMD2 = 0V (38.4kbps) 4
Direction Duration High tDIR, HIGH 137 µs VDIRMD1 = 0V, VDIRMD2 = 3.3V (115.2kbps) 4

CAD (KiCad official)

  • Symbol: MAX9947ETE+T
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: max9947ete-t-etched.step / max9947ete-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max9947ete-t.step / max9947ete-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Maxim Integrated datasheet (17 pp, sha256 56963b82445bcb7d, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF