Generated by kicad-footprint-generator · KiCad file format 20260206
MAX9939AUB+T
Maxim Integrated · Differential OpAmps · MSOP-10
MAX9939AUB+T from Maxim Integrated, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | input | Serial-Clock Input for the SPI interface; data is clocked into the serial interface on the rising edge of SCLK, with fSCLK up to 5MHz. |
| 2 | DIN | input | Serial-Data Input; data is clocked into the serial interface on the rising edge of SCLK, with DIN setup to SCLK of 55ns minimum. |
| 3 | GND | power_in | Ground reference for the device, with VCC supplied from 2.9V to 5.5V relative to GND. |
| 4 | INA- | input | PGA Inverting Input, which accepts signals up to ±16V relative to GND without damage per the absolute maximum ratings. |
| 5 | INA+ | input | PGA Noninverting Input, which accepts signals up to ±16V relative to GND without damage per the absolute maximum ratings. |
| 6 | OUTB | output | Buffer (amplifier B) Output, which is high impedance in shutdown mode and must be kept within VCC + 0.3V absolute maximum. |
| 7 | INB | input | Buffer Input for the uncommitted output op amp (amplifier B), whose noninverting input is referenced to VCC/2. |
| 8 | OUTA | output | PGA Output, which is referenced to VCC/2 and must be kept within -0.3V to VCC + 0.3V absolute maximum. |
| 9 | VCC | power_in | Power Supply, which operates from 2.9V to 5.5V and should be bypassed to GND with 0.1µF and 1µF capacitors. |
| 10 | CS | input | Active-Low Chip-Select Input; drive CS low to enable the serial interface and high to disable it. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | MSOP-10 |
| Category | Operational Amplifier/Comparator |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC to GND | -0.3 | 6 | V | 2 | |||
| INB, OUTA, OUTB, SCLK, DIN, CS voltage | -0.3 | V | max printed as VCC + 0.3V | 2 | |||
| INA+, INA- to GND | -16 | 16 | V | 2 | |||
| Continuous input current into any terminal | -20 | 20 | mA | 2 | |||
| Operating temperature range | TA | -40 | 125 | °C | 2 | ||
| Junction temperature | TJ | 150 | °C | 2 | |||
| Storage temperature range | TSTORE | -65 | 150 | °C | 2 | ||
| Lead temperature (soldering) | 300 | °C | soldering, 10s | 2 | |||
| Soldering temperature (reflow) | 260 | °C | reflow | 2 | |||
| Gain error | GE | 0.05 | 0.38 | % | TA = +25°C, 0.2V ≤ VOUTA ≤ VCC - 0.2V | 2 | |
| Gain temperature coefficient | Tc-GE | 2.2 | 17 | ppm/°C | 2 | ||
| Input offset voltage (no VOS trim) | VOS-A | 1.5 | 9 | mV | With no VOS trim, TA = +25°C | 2 | |
| Input offset voltage (no VOS trim, full temperature) | VOS-A | 15 | mV | With no VOS trim, TA = TMIN to TMAX | 2 | ||
| Input offset-voltage trim range | -17 | 17 | mV | 2 | |||
| Common-mode rejection ratio | CMRR | 50 | 60 | dB | -1V ≤ VCM ≤ VCC - 2.2V | 2 | |
| Common-mode rejection ratio | CMRR | 39 | dB | -VCC/2 ≤ VCM ≤ VCC - 2.2V | 2 | ||
| Max capacitive load | CL(MAX) | 1 | nF | 2 | |||
| Output swing | VOH, VOL | 25 | 60 | mV | Voltage output high = VCC - VOUTA; voltage output low = VOUTA - VGND | 2 | |
| Input offset voltage (output amplifier B) | VOS-B | 1.5 | 9 | mV | TA = +25°C | 2 | |
| Input offset voltage (output amplifier B, full temperature) | VOS-B | 15 | mV | TA = TMIN to TMAX | 2 | ||
| Output swing (amplifier B) | VOH, VOL | 25 | 60 | mV | Voltage output high = VCC - VOUTB; voltage output low = VOUTB - VGND | 3 | |
| Power-supply rejection ratio | PSRR | 60 | 80 | dB | 1kΩ between OUTA and INB, 1kΩ between OUTB and INB, measured differentially between OUTA and OUTB | 3 | |
| Supply voltage range | VCC | 2.9 | 5.5 | V | Guaranteed by PSRR | 3 | |
| Supply current | ICC | 3.4 | 6.7 | mA | OUTA and OUTB unloaded | 3 | |
| Shutdown supply current | ISHDN | 13 | 24 | µA | Soft shutdown through SPI | 3 | |
| Input-voltage low | VIL | 0.8 | V | 3 | |||
| Input-voltage high | VIH | 2 | V | VCC = 5V | 3 | ||
| Input-voltage high | VIH | 1.65 | V | VCC = 3.3V | 3 | ||
| Input leakage current | IIN | -1 | 1 | µA | 3 |
CAD (KiCad official)
- Symbol:
MAX9939AUB+T - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
max9939aub-t-etched.step/max9939aub-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max9939aub-t.step/max9939aub-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Maxim Integrated datasheet (15 pp, sha256
c993934c250fed74, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).