3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMAX96714FGTJ
Analog Devices Inc./Maxim Integrated · Serializers, Deserializers · TQFN-32(5x5)
MAX96714FGTJ from Analog Devices Inc./Maxim Integrated, in a TQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MFP0 | bidirectional | Multifunction pin: MS UART mode select (1MΩ pull-down, low=Base, high=Bypass), VS, FSYNC_OUT, DE/DV or GPIO0 (power-up default GPI with 1MΩ pull-down). |
| 2 | MFP1 | bidirectional | Multifunction pin: pass-through SDA1/RX1 or SDA2/RX2 (40kΩ pull-up to VDDIO) or GPIO1. |
| 3 | MFP2 | bidirectional | Multifunction pin: pass-through SCL1/TX1 or SCL2/TX2 (40kΩ pull-up to VDDIO), MS, FSYNC_OUT or GPIO2. |
| 4 | MFP3 | bidirectional | Primary I2C data input/open-drain output (SDA) or UART RX, with 40kΩ pull-up to VDDIO. |
| 5 | CFG0 | input | Configuration pin whose voltage is latched at power-up to select I2C/UART and device address (see Table 8); set by resistor divider from VDDIO. |
| 6 | MFP4 | bidirectional | Primary I2C clock input/open-drain output (SCL) or UART TX, with 40kΩ pull-up to VDDIO. |
| 7 | MFP5 | bidirectional | Multifunction pin: LOCK open-drain indication output (40kΩ pull-up to VDDIO), VS, DE/DV or GPIO5. |
| 8 | X1/OSC | input | Crystal/oscillator input; connect a 25MHz crystal, or the oscillator output if an oscillator is used. |
| 9 | X2 | passive | Connect the other terminal of the 25MHz crystal; leave floating if an oscillator is used. |
| 10 | XRES | passive | Connect a 402Ω ±1% resistor between XRES and ground. |
| 11 | VDD18 | power_in | 1.8V analog supply (1.7V to 1.9V). |
| 12 | SION/SIO | bidirectional | Inverted twisted-pair serial-data I/O (SION) or coax serial-data I/O (SIO), selected by CFG1 state at power-up. |
| 13 | SIOP | bidirectional | Noninverted twisted-pair serial-data input/output, configuration determined by CFG1 state at power-up. |
| 14 | CAP_VDD | passive | Decoupling capacitor pin for the 1.0V core supply. |
| 15 | VDD | power_in | 1.0V core supply with optional on-chip LDO: connect 0.95V to 1.05V to bypass the LDO, or 1.14V to 1.26V to use the internal 1.0V regulator. |
| 16 | CFG1 | input | Configuration pin whose voltage is latched at power-up to select coax/twisted pair, GMSL mode and tunnel/pixel mode (see Table 9). |
| 17 | VDDIO | power_in | 1.8V to 3.3V I/O supply. |
| 18 | MFP6 | bidirectional | Multifunction pin: LMN0 line-fault monitor input or GPIO6 (power-up default GPI6 with 1MΩ pull-down). |
| 19 | MFP7 | bidirectional | Multifunction pin: LMN1 line-fault monitor input or GPIO7 (power-up default GPI7 with 1MΩ pull-down). |
| 20 | VTERM | power_in | 1.2V D-PHY supply (1.14V to 1.26V). |
| 21 | D0P | output | CSI-2 data lane 0 noninverted output. |
| 22 | D0N | output | CSI-2 data lane 0 inverted output. |
| 23 | D1P | output | CSI-2 data lane 1 noninverted output. |
| 24 | D1N | output | CSI-2 data lane 1 inverted output. |
| 25 | D2P | output | CSI-2 data lane 2 noninverted output. |
| 26 | D2N | output | CSI-2 data lane 2 inverted output. |
| 27 | CKP | output | CSI-2 clock lane noninverted output. |
| 28 | CKN | output | CSI-2 clock lane inverted output. |
| 29 | D3P | output | CSI-2 data lane 3 noninverted output. |
| 30 | D3N | output | CSI-2 data lane 3 inverted output. |
| 31 | PWDNB | input | Active-low power-down input with 1MΩ pull-down to ground; set low to enter power-down mode. |
| 32 | MFP8 | bidirectional | Multifunction pin: ERRB open-drain error output (40kΩ pull-up to VDDIO, low indicates error) or GPIO8. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | TQFN-32(5x5) |
| Category | Interface |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage swing (single-ended) GMSL2 | VO | 190 | 250 | 310 | mV | RL = 100Ω ±1% | 7 |
| Output voltage swing (differential) GMSL2 | VODT | 380 | 500 | 620 | mV | RL = 100Ω ±1%, peak-to-peak differential voltage | 7 |
| Change in VOD between complementary output states | ΔVOD | 25 | mV | RL = 100Ω ±1%, /VOD(H) − VOD(L)/ | 7 | ||
| Termination resistance (internal) GMSL2 | RT | 50 | 55 | 60 | Ω | Any Pin to VDD18 | 7 |
| D-PHY LP high-level output voltage | VOH | 0.95 | 1.2 | 1.3 | V | 7 | |
| D-PHY LP low-level output voltage | VOL | -50 | 50 | mV | 7 | ||
| HS transmit static common mode voltage | VCMTX | 150 | 200 | 250 | mV | See Figure 3 | 7 |
| HS transmit differential voltage | /VOD/ | 140 | 200 | 270 | mV | See Figure 3 | 8 |
| Single-ended output impedance | ZOS | 40 | 50 | 62.5 | Ω | 8 | |
| I/O pin input current | IIN | 1 | μA | All pull-up/pull-down devices disabled. VIN = 0V to VDDIO | 8 | ||
| I/O output high voltage drop | VOH | 0.4 | V | IOH = -4mA; min is VDDIO - 0.4V (printed relative to VDDIO); max inferred | 8 | ||
| I/O low-level output voltage | VOL | 0.4 | V | IOL = 4mA | 8 | ||
| Supply current VDD (3Gbps, 1.0V) | IDD | 78 | 220 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane (MAX96714F/R), VDD = 1.0V | 9 | |
| Supply current VDD (3Gbps, 1.2V) | IDD | 80 | 210 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane (MAX96714F/R), VDD = 1.2V | 9 | |
| Supply current VDD18 (3Gbps) | IDD | 114 | 155 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane (MAX96714F/R), VDD18 = 1.8V | 9 | |
| Supply current VTERM (3Gbps) | IDD | 14 | 22 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane (MAX96714F/R), VTERM = 1.2V | 9 | |
| Maximum power-down current VDDIO | IDD | 6 | μA | VDDIO at 3.6V, TA = 25°C and 105°C | 10 | ||
| Maximum power-down current VDD18 | IDD | 10 | μA | VDD18 at 1.9V, TA = 105°C (1 μA at 25°C) | 10 | ||
| GMSL2 lock time | tLOCK2 | 31 | ms | From power-up, one-shot reset, or rising edge of PWDNB to rising edge of LOCK | 10 | ||
| I2C/UART output fall time | tF | 150 | ns | 70% to 30%, CL = 20pF to 100pF, 1kΩ pull-up to VDDIO | 13 | ||
| I2C/UART wake time | tWAKEUP | 12.25 | ms | From power-up, or rising edge of PWDNB to local register access | 13 | ||
| Crystal frequency stability + tolerance | fTN | -200 | 200 | ppm | Crystal reference clock | 15 | |
| Crystal frequency | fXTAL | 25 | MHz | 14 | |||
| Supply VTERM | VTERM | 1.14 | 1.2 | 1.26 | V | 22 | |
| Supply VDD18 | VDD18 | 1.7 | 1.8 | 1.9 | V | 22 | |
| Supply VDD (1.0V nominal) | VDD | 0.95 | 1 | 1.05 | V | Nominal 1.0V | 22 |
| Supply VDD (1.2V nominal) | VDD | 1.14 | 1.2 | 1.26 | V | Nominal 1.2V | 22 |
| Supply VDDIO | VDDIO | 1.7 | 3.6 | V | 22 | ||
| Operating junction temperature | TJ | -40 | 125 | ºC | 22 | ||
| Operating ambient temperature | TA | -40 | 105 | °C | 53 | ||
| VDDIO absolute maximum | VDDIO | -0.3 | 3.9 | V | With respect to ground | 6 | |
| VDD18 absolute maximum | VDD18 | -0.3 | 2 | V | With respect to ground | 6 | |
| VDD absolute maximum | VDD | -0.3 | 2 | V | With respect to ground | 6 | |
| VTERM absolute maximum | VTERM | -0.3 | 1.32 | V | With respect to ground | 6 | |
| CAP_VDD absolute maximum | CAP_VDD | -0.3 | 1.2 | V | With respect to ground | 6 | |
| SIO_ inactive state voltage | SIO_ | -0.3 | 1.1 | V | Inactive state | 6 | |
| Storage temperature range | -40 | 150 | °C | 6 | |||
| Soldering temperature (reflow) | 260 | °C | 6 | ||||
| Junction to ambient thermal resistance | θJA | 29 | °C/W | 32-Pin TQFN, four-layer board | 6 | ||
| Junction to case thermal resistance | θJC | 1.7 | °C/W | 32-Pin TQFN, four-layer board | 6 |
CAD (KiCad official)
- Symbol:
MAX96714FGTJ - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
max96714fgtj-etched.step/max96714fgtj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max96714fgtj.step/max96714fgtj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc./Maxim Integrated datasheet (165 pp, sha256
51fc4d62cdc4e20f, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).