Generated by kicad-footprint-generator · KiCad file format 20260206
MAX3491AEIM
HGSEMI · RS-485/RS-422 ICs · SOP-14
MAX3491AEIM from HGSEMI, in a SOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | N.C. | unconnected | No internal connection; the pin may be grounded. |
| 2 | RO | output | Receiver output: with RE low, RO goes high when (A - B) is not less than 200 mV and goes low when (A - B) is not greater than -200 mV. |
| 3 | RE | input | Receiver output enable, active low: RO is enabled when RE is low and is high-impedance when RE is high; RE high with DE low puts the device into low-power shutdown, and RE has a hot-plug input structure. |
| 4 | DE | input | Driver output enable: the driver outputs are active when DE is high and high-impedance when DE is low; RE high with DE low puts the device into low-power shutdown, and DE has a hot-plug input structure. |
| 5 | DI | input | Driver input: with DE high, a low on DI drives output A/Y low and B/Z high, and a high on DI drives A/Y high and B/Z low. |
| 6 | GND | power_in | Ground. |
| 7 | GND | power_in | Ground. |
| 8 | N.C. | unconnected | No internal connection; the pin may be grounded. |
| 9 | Y | output | Driver non-inverting output. |
| 10 | Z | output | Driver inverting output. |
| 11 | B | bidirectional | Receiver inverting input (also the driver inverting output B/Z in half-duplex naming). |
| 12 | A | bidirectional | Receiver non-inverting input (also the driver non-inverting output A/Y in half-duplex naming). |
| 13 | N.C. | unconnected | No internal connection; the pin may be grounded. |
| 14 | VCC | power_in | Positive supply: 3.15 V ≤ VCC ≤ 3.45 V; connect a 0.1 µF capacitor to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-14 |
| Category | Communication Interface Chip |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 6 | V | 3 | |||
| Control input voltage | RE, DE | -0.3 | 6 | V | 3 | ||
| Driver input voltage | DI | -0.3 | 6 | V | 3 | ||
| Driver output voltage | A,B,Y,Z | -7 | 12 | V | 3 | ||
| Receiver input voltage | A,B | -7 | 12 | V | 3 | ||
| Receiver output voltage | RO | -0.3 | V | Upper limit printed as VCC+0.3 | 3 | ||
| Continuous power dissipation | 667 | mW | TA=+70 C, 14SOP package | 3 | |||
| Operating temperature range | TA | -40 | 85 | ℃ | MAX3491AEI (industrial grade) | 3 | |
| Storage temperature | TSTORE | -65 | 150 | ℃ | 3 | ||
| Lead temperature | TLEAD | 245 | ℃ | Soldering 10 s | 3 | ||
| Differential driver output voltage | VOD | 2 | V | Fig.1, RL=100 ohm (RS-422); max printed as VCC | 3 | ||
| Differential driver output voltage | VOD | 1.5 | V | Fig.1, RL=54 ohm (RS-485); max printed as VCC | 3 | ||
| Change in differential driver output voltage magnitude | dVOD | 0.2 | V | Fig.1, RL=100 ohm or RL=54 ohm | 3 | ||
| Driver common-mode output voltage | VOC | 3 | V | Fig.1, RL=100 ohm or RL=54 ohm; min printed as VCC/2 | 3 | ||
| Change in common-mode output voltage magnitude | dVOC | 0.2 | V | Fig.1, RL=100 ohm or RL=54 ohm | 3 | ||
| Input high voltage | VIH | 2 | V | DE, DI, RE | 4 | ||
| Input low voltage | VIL | 0.8 | V | DE, DI | 4 | ||
| Input current | IIN | -1 | 1 | μA | DE, DI, RE | 4 | |
| Input current (A,B) full duplex | IA, IB | 125 | μA | DE=GND, VCC=GND or VCC, VIN=12V | 4 | ||
| Input current (A,B) full duplex | IA, IB | -75 | μA | DE=GND, VCC=GND or VCC, VIN=-7V | 4 | ||
| Output leakage current (Y,Z) full duplex | IO | 125 | μA | DE=GND, VCC=GND or VCC, VIN=12V | 4 | ||
| Output leakage current (Y,Z) full duplex | IO | -100 | μA | DE=GND, VCC=GND or VCC, VIN=-7V | 4 | ||
| Driver short-circuit output current | IOSD | 250 | mA | 0 <= VOUT <= 12V | 4 | ||
| Driver short-circuit output current | IOSD | -250 | mA | -7 <= VOUT <= VCC | 4 | ||
| Receiver differential threshold voltage | VTH | -200 | 200 | mV | -7V <= VCM <= 12V | 4 | |
| Receiver output low voltage | VOL | 0.4 | V | IO=4mA, VID=-200mV | 4 | ||
| Receiver tri-state output current | IOZR | -1 | 1 | μA | 0 <= VO <= VCC | 4 | |
| Receiver output short-circuit current | IOSR | -95 | 95 | mA | 0V <= VRO <= VCC | 4 | |
| Supply current | ICC | 400 | 900 | μA | No load, RE=VCC, DI=GND or VCC, DE=VCC | 4 | |
| Supply current | ICC | 330 | 600 | μA | No load, RE=VCC, DI=GND or VCC, DE=GND | 4 | |
| Supply current | ICC | 400 | 1000 | μA | No load, RE=GND, DI=GND or VCC, DE=VCC | 4 | |
| Supply current | ICC | 330 | 800 | μA | No load, RE=GND, DI=GND or VCC, DE=GND | 4 | |
| Standby supply current | ISHDN | 0.05 | 10 | μA | DE=GND, RE=VCC | 4 | |
| Thermal shutdown temperature | TTS | 165 | ℃ | 4 | |||
| Thermal shutdown hysteresis | TTSH | 15 | ℃ | 4 | |||
| Input hysteresis | VHYS | 100 | mV | DE, DI, RE | 4 | ||
| Receiver input hysteresis | dVTH | 15 | mV | VA+VB=0 | 4 | ||
| Receiver input resistance | RIN | 96 | kΩ | -7V <= VCM <= 12V | 4 | ||
| Driver propagation delay tDPLH | tDPLH | 50 | ns | Fig.2 and 5, RL=54 ohm, CL=50pF | 5 | ||
| Driver propagation delay tDPHL | tDPHL | 50 | ns | Fig.2 and 5, RL=54 ohm, CL=50pF | 5 | ||
| Driver skew /tDPLH-tDPHL/ | tDSKEW | 10 | ns | Fig.2 and 5, RL=54 ohm, CL=50pF | 5 | ||
| Driver rise/fall time | tDR, tDF | 20 | ns | Fig.2 and 5, RL=54 ohm, CL=50pF | 5 | ||
| Maximum data rate (driver) | fMAX | 16 | Mbps | 5 | |||
| Receiver enable to output low | tDZL | 150 | ns | Fig.3 and 6, CL=100pF, S3 closed | 5 | ||
| Receiver enable to output high | tDZH | 150 | ns | Fig.3 and 6, CL=100pF, S2 closed | 5 | ||
| Receiver low-to-invalid time | tDLZ | 100 | ns | Fig.3 and 6, CL=15pF, S2 closed | 5 | ||
| Receiver high-to-invalid time | tDHZ | 100 | ns | Fig.3 and 6, CL=15pF, S3 closed | 5 | ||
| Enable from standby to output high | tDZH(SHDN) | 2200 | ns | Fig.3 and 6, CL=15pF, S3 closed | 5 | ||
| Enable from standby to output low | tDZL(SHDN) | 2200 | ns | Fig.3 and 6, CL=15pF, S2 closed | 5 | ||
| Standby time | tSHDN | 50 | 350 | 700 | ns | Driver | 5 |
| Receiver propagation delay | tRPLH, tRPHL | 50 | ns | Fig.7 and 8, CL=15pF, /VID/>=2.0V, VID<=15ns | 5 | ||
| Receiver skew | tRSKEW | 20 | ns | Fig.7 and 8, CL=15pF, /VID/>=2.0V, VID<=15ns | 5 | ||
| Receiver enable to output low | tRZL | 50 | ns | Fig.4 and 9, S1=-1.3.3V, S2 to VCC | 5 | ||
| Receiver enable to output high | tRZH | 50 | ns | Fig.4 and 9, S1=+1.3.3V, S2 to GND | 5 | ||
| Receiver low-to-invalid time | tRLZ | 50 | ns | Fig.4 and 9, S1=-1.3.3V, S2 to VCC | 5 | ||
| Receiver high-to-invalid time | tRHZ | 50 | ns | Fig.4 and 9, S1=+1.3.3V, S2 to GND | 5 | ||
| Enable from standby to output high (receiver) | tRZH(SHDN) | 2200 | ns | Fig.4 and 9, S1=-1.3.3V, S2 to VCC | 5 | ||
| Enable from standby to output low (receiver) | tRZL(SHDN) | 2200 | ns | Fig.4 and 9, S1=+1.3.3V, S2 to GND | 5 |
CAD (KiCad official)
- Symbol:
MAX3491AEIM - Footprint:
Package_SO:SOIC-14_3.9x8.7mm_P1.27mm - 3D model: SOP-14 (KiCad packages3D, STEP)
- 3D model files:
max3491aeim-etched.step/max3491aeim-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3491aeim.step/max3491aeim.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet, copy hosted by JLCPCB (15 pp, sha256
ad5b3a9aae85f547, retrieved 2026-11-21) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).