Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX3225EEUP+T

Analog Devices Inc Maxim Integrated · RS232 ICs · TSSOP-20

MAX3225EEUP+T from Analog Devices Inc Maxim Integrated, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 READY output Ready to Transmit output, active-high, which is enabled high when V- goes below -4V and the device is ready to transmit.
2 C1+ passive Positive terminal of the voltage-doubler charge-pump capacitor.
3 V+ power_out +5.5V generated by the charge pump.
4 C1- passive Negative terminal of the voltage-doubler charge-pump capacitor.
5 C2+ passive Positive terminal of the inverting charge-pump capacitor.
6 C2- passive Negative terminal of the inverting charge-pump capacitor.
7 V- power_out -5.5V generated by the charge pump.
8 T2OUT output RS-232 transmitter output, forced to high impedance when FORCEOFF is low or AutoShutdown Plus disables the transmitters, with T_OUT limited to ±13.2V to GND.
9 R2IN input RS-232 receiver input, rated to ±25V to GND.
10 R2OUT output TTL/CMOS receiver output, limited to -0.3V to (VCC + 0.3V) to GND.
11 INVALID output Valid signal detector output, active-low; a logic high indicates that a valid RS-232 level is present on a receiver input.
12 T2IN input TTL/CMOS transmitter input with no pullup resistor, so unused inputs must be connected to GND or VCC.
13 T1IN input TTL/CMOS transmitter input with no pullup resistor, so unused inputs must be connected to GND or VCC.
14 FORCEON input Force-On input, active-high, which overrides AutoShutdown Plus to keep transmitters and receivers on, provided FORCEOFF is high.
15 R1OUT output TTL/CMOS receiver output, limited to -0.3V to (VCC + 0.3V) to GND.
16 R1IN input RS-232 receiver input, rated to ±25V to GND.
17 T1OUT output RS-232 transmitter output, forced to high impedance when FORCEOFF is low or AutoShutdown Plus disables the transmitters, with T_OUT limited to ±13.2V to GND.
18 GND power_in Ground reference for the device.
19 VCC power_in Single supply voltage input, +3.0V to +5.5V.
20 FORCEOFF input Force-Off input, active-low; when low, transmitters are in high impedance, charge pumps are shut down, and receivers are active, overriding AutoShutdown Plus and FORCEON.

Key specifications

Parameter Value
Manufacturer Analog Devices Inc Maxim Integrated
Package TSSOP-20
Category Interface
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC (test condition range) VCC 3 5.5 V VCC = +3V to +5.5V (EC table header) 6
Operating Temperature Range (MAX32__EE__) -40 85 °C EE grade 2
VCC to GND VCC -0.3 6 V 2
V+ to GND V+ -0.3 7 V Note 1 2
V- to GND V- -7 0.3 V Note 1 2
V+ + /V-/ 13 V Note 1 2
Input voltages T_IN, FORCEON, FORCEOFF to GND -0.3 6 V 2
R_IN to GND -25 25 V 2
T_OUT to GND -13.2 13.2 V 2
Storage Temperature Range -65 160 °C 2
Lead Temperature (soldering, 10s) 300 °C soldering 10s 2
Soldering Temperature (reflow) 260 °C reflow 2
Supply Current, AutoShutdown Plus 1 10 μA FORCEON = GND, FORCEOFF = VCC, all R_IN idle, all T_IN idle; VCC = 3.3V or 5.0V, TA = +25°C 6
Supply Current, Shutdown 1 10 μA FORCEOFF = GND; VCC = 3.3V or 5.0V, TA = +25°C 6
Supply Current, AutoShutdown Plus Disabled 0.3 1 mA FORCEON = FORCEOFF = VCC, no load; VCC = 3.3V or 5.0V, TA = +25°C 6
Input Logic Threshold Low 0.8 V T_IN, FORCEON, FORCEOFF 6
Input Logic Threshold High 2 V T_IN, FORCEON, FORCEOFF; VCC = 3.3V 6
Input Logic Threshold High 2.4 V T_IN, FORCEON, FORCEOFF; VCC = 5.0V 6
Input Leakage Current -1 1 μA T_IN, FORCEON, FORCEOFF 6
Output Voltage Low 0.4 V IOUT = 1.6mA 6
Receiver Input Voltage Range -25 25 V 6
Receiver Input Threshold Low 0.6 1.2 V TA = +25°C; VCC = 3.3V 6
Receiver Input Threshold Low 0.8 1.5 V TA = +25°C; VCC = 5.0V 6
Receiver Input Threshold High 1.5 2.4 V TA = +25°C; VCC = 3.3V 6
Receiver Input Threshold High 1.8 2.4 V TA = +25°C; VCC = 5.0V 6
Input Resistance 3 5 7 kΩ TA = +25°C 6
Output Voltage Swing -5 5.4 5 V All transmitter outputs loaded with 3kΩ to ground 6
Output Resistance (minimum) 300 Ω VCC = V+ = V- = 0V, transmitter outputs = ±2V 6
Output Resistance (maximum) 10 MΩ VCC = V+ = V- = 0V, transmitter outputs = ±2V 6
Output Short-Circuit Current -60 60 mA 6
Output Leakage Current (transmitter outputs) -25 25 μA VCC = 0V or 3V to 5.5V, VOUT = ±12V, transmitters disabled 6
ESD IEC 1000-4-2 Air Discharge (R_IN, T_OUT) -15 15 kV R_IN, T_OUT 7
ESD IEC 1000-4-2 Contact Discharge (R_IN, T_OUT) -8 8 kV R_IN, T_OUT 7
ESD Human Body Model (R_IN, T_OUT) -15 15 kV R_IN, T_OUT 7
Receiver Input Threshold to INVALID Output High, positive threshold 2.7 V FORCEON = GND, FORCEOFF = VCC; Figure 4a 7
Receiver Input Threshold to INVALID Output High, negative threshold -2.7 V FORCEON = GND, FORCEOFF = VCC; Figure 4a 7
Receiver Input Threshold to INVALID Output Low -0.3 0.3 V FORCEON = GND, FORCEOFF = VCC; Figure 4a 7
INVALID, READY Output Voltage Low (MAX3224E-MAX3227E) 0.4 V IOUT = -1.6mA 7
Receiver Positive or Negative Threshold to INVALID High tINVH 1 μs VCC = 5V, Figure 4b 7
Receiver Positive or Negative Threshold to INVALID Low tINVL 30 μs VCC = 5V, Figure 4b 7
Receiver or Transmitter Edge to Transmitters Enabled tWU 100 μs VCC = 5V, Figure 5b (Note 2) 7
Receiver or Transmitter Edge to Transmitters Shutdown tAUTOSHDN 15 30 60 s VCC = 5V, Figure 5b (Note 2) 7
Maximum Data Rate 1000 kbps VCC = 3.0V to 4.5V, RL = 3kΩ, CL = 250pF, one transmitter switching 8
Transmitter Skew /tPHL - tPLH/ 25 ns Note 3 8
Receiver Skew /tPHL - tPLH/ 50 ns 8
Transition-Region Slew Rate 24 150 V/μs VCC = 3.3V, TA = +25°C, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF, one transmitter switching 8

CAD (KiCad official)

  • Symbol: MAX3225EEUP+T
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: max3225eeup-t-etched.step / max3225eeup-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max3225eeup-t.step / max3225eeup-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices Inc Maxim Integrated datasheet (25 pp, sha256 8542587c6f3a36a5, retrieved 2026-10-18, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF