main
Ray
Publish 0.1.0
36cfab4
MAX3223ECPWR
Texas Instruments · RS232 ICs · TSSOP-20
MAX3223ECPWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Receiver enable input: when high, the receiver outputs (ROUT1, ROUT2) are placed in high impedance; input range is 0 V to 5.5 V. |
| 2 | C1+ | passive | Positive terminal of charge-pump capacitor C1, which must be connected per the recommended values (0.1 µF at VCC = 3.3 V; 0.047 µF at VCC = 5 V). |
| 3 | V+ | power_out | Positive charge-pump output rail generated from VCC; absolute maximum is -0.3 V to 7 V and it must be bypassed with a ceramic capacitor as shown in Figure 7-1. |
| 4 | C1− | passive | Negative terminal of charge-pump capacitor C1, which must be connected per the recommended values in Figure 7-1. |
| 5 | C2+ | passive | Positive terminal of charge-pump capacitor C2, which must be connected per the recommended values (0.33 µF at VCC = 5 V; 0.1 µF at VCC = 3.3 V). |
| 6 | C2− | passive | Negative terminal of charge-pump capacitor C2, which must be connected per the recommended values in Figure 7-1. |
| 7 | V− | power_out | Negative charge-pump output rail; absolute maximum is -7 V to 0.3 V and it must be bypassed with a ceramic capacitor as shown in Figure 7-1. |
| 8 | DOUT2 | output | RS-232 driver 2 output with ±15 kV HBM ESD protection; with RL = 3 kΩ to GND it swings to at least ±5 V (VOH/VOL), and the output is high impedance when FORCEOFF is low. |
| 9 | RIN2 | input | RS-232 receiver 2 input with ±15 kV HBM ESD protection; receiver input voltage range is -25 V to 25 V. |
| 10 | ROUT2 | output | CMOS-level receiver 2 output that goes high-impedance when EN is high; VOH is at least VCC - 0.6 V at IOH = -1 mA. |
| 11 | INVALID | output | Output that is high when any receiver input is a valid RS-232 level (above 2.7 V or below -2.7 V, or not held within ±0.3 V for more than 30 µs) and low when no valid signal is detected. |
| 12 | DIN2 | input | Logic input to driver 2 with a control/driver input range of 0 V to 5.5 V and a low-level input maximum of 0.8 V. |
| 13 | DIN1 | input | Logic input to driver 1 with a control/driver input range of 0 V to 5.5 V and a low-level input maximum of 0.8 V. |
| 14 | FORCEON | input | Auto-powerdown control: when low with FORCEOFF high, auto-powerdown is enabled; when high with FORCEOFF high, auto-powerdown is disabled. Input range is 0 V to 5.5 V. |
| 15 | ROUT1 | output | CMOS-level receiver 1 output that goes high-impedance when EN is high; VOH is at least VCC - 0.6 V at IOH = -1 mA. |
| 16 | RIN1 | input | RS-232 receiver 1 input with ±15 kV HBM ESD protection; receiver input voltage range is -25 V to 25 V. |
| 17 | DOUT1 | output | RS-232 driver 1 output with ±15 kV HBM ESD protection; with RL = 3 kΩ to GND it swings to at least ±5 V (VOH/VOL), and the output is high impedance when FORCEOFF is low. |
| 18 | GND | power_in | Network ground and reference for all device voltages. |
| 19 | VCC | power_in | Supply voltage of 3 V to 5.5 V (absolute maximum -0.3 V to 6 V); must be bypassed with at least 1 µF to GND to meet the IEC 61000-4-2 rating. |
| 20 | FORCEOFF | input | Active-low driver shutdown: when low, the device is powered off, the drivers are disabled and outputs are high impedance; input range is 0 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-20 |
| Category | Interface |
| Pins | 20 |
CAD (KiCad official)
- Symbol:
MAX3223ECPWR - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
max3223ecpwr-etched.step/max3223ecpwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3223ecpwr.step/max3223ecpwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (28 pp, sha256
45ca048c81e9b2a5, retrieved 2026-10-11, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MAX3223ECPWR
**Texas Instruments** · RS232 ICs · TSSOP-20
MAX3223ECPWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Receiver enable input: when high, the receiver outputs (ROUT1, ROUT2) are placed in high impedance; input range is 0 V to 5.5 V. |
| 2 | C1+ | passive | Positive terminal of charge-pump capacitor C1, which must be connected per the recommended values (0.1 µF at VCC = 3.3 V; 0.047 µF at VCC = 5 V). |
| 3 | V+ | power_out | Positive charge-pump output rail generated from VCC; absolute maximum is -0.3 V to 7 V and it must be bypassed with a ceramic capacitor as shown in Figure 7-1. |
| 4 | C1− | passive | Negative terminal of charge-pump capacitor C1, which must be connected per the recommended values in Figure 7-1. |
| 5 | C2+ | passive | Positive terminal of charge-pump capacitor C2, which must be connected per the recommended values (0.33 µF at VCC = 5 V; 0.1 µF at VCC = 3.3 V). |
| 6 | C2− | passive | Negative terminal of charge-pump capacitor C2, which must be connected per the recommended values in Figure 7-1. |
| 7 | V− | power_out | Negative charge-pump output rail; absolute maximum is -7 V to 0.3 V and it must be bypassed with a ceramic capacitor as shown in Figure 7-1. |
| 8 | DOUT2 | output | RS-232 driver 2 output with ±15 kV HBM ESD protection; with RL = 3 kΩ to GND it swings to at least ±5 V (VOH/VOL), and the output is high impedance when FORCEOFF is low. |
| 9 | RIN2 | input | RS-232 receiver 2 input with ±15 kV HBM ESD protection; receiver input voltage range is -25 V to 25 V. |
| 10 | ROUT2 | output | CMOS-level receiver 2 output that goes high-impedance when EN is high; VOH is at least VCC - 0.6 V at IOH = -1 mA. |
| 11 | INVALID | output | Output that is high when any receiver input is a valid RS-232 level (above 2.7 V or below -2.7 V, or not held within ±0.3 V for more than 30 µs) and low when no valid signal is detected. |
| 12 | DIN2 | input | Logic input to driver 2 with a control/driver input range of 0 V to 5.5 V and a low-level input maximum of 0.8 V. |
| 13 | DIN1 | input | Logic input to driver 1 with a control/driver input range of 0 V to 5.5 V and a low-level input maximum of 0.8 V. |
| 14 | FORCEON | input | Auto-powerdown control: when low with FORCEOFF high, auto-powerdown is enabled; when high with FORCEOFF high, auto-powerdown is disabled. Input range is 0 V to 5.5 V. |
| 15 | ROUT1 | output | CMOS-level receiver 1 output that goes high-impedance when EN is high; VOH is at least VCC - 0.6 V at IOH = -1 mA. |
| 16 | RIN1 | input | RS-232 receiver 1 input with ±15 kV HBM ESD protection; receiver input voltage range is -25 V to 25 V. |
| 17 | DOUT1 | output | RS-232 driver 1 output with ±15 kV HBM ESD protection; with RL = 3 kΩ to GND it swings to at least ±5 V (VOH/VOL), and the output is high impedance when FORCEOFF is low. |
| 18 | GND | power_in | Network ground and reference for all device voltages. |
| 19 | VCC | power_in | Supply voltage of 3 V to 5.5 V (absolute maximum -0.3 V to 6 V); must be bypassed with at least 1 µF to GND to meet the IEC 61000-4-2 rating. |
| 20 | FORCEOFF | input | Active-low driver shutdown: when low, the device is powered off, the drivers are disabled and outputs are high impedance; input range is 0 V to 5.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-20 |
| Category | Interface |
| Pins | 20 |
## CAD (KiCad official)
- Symbol: `MAX3223ECPWR`
- Footprint: `Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm`
- 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files: `max3223ecpwr-etched.step` / `max3223ecpwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `max3223ecpwr.step` / `max3223ecpwr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/max3223e) (28 pp, sha256 `45ca048c81e9b2a5`, retrieved 2026-10-11, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/max3223ecpwr-datasheet.pdf)