main
Ray
Publish 0.1.0
15821ee
MAX3221EETE+
Maxim Integrated · RS232 ICs · TQFN-16(5x5)
MAX3221EETE+ from Maxim Integrated, in a TQFN-16(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1- | passive | Negative terminal of the voltage doubler charge-pump capacitor. |
| 2 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 3 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 4 | V- | power_out | -5.5V generated by the charge pump. |
| 5 | R1IN | input | RS-232 receiver input, protected to ±15kV ESD and with an input voltage range of -25V to +25V. |
| 6 | R1OUT | tri_state | TTL/CMOS receiver output that goes high-impedance when EN is driven high. |
| 7 | INVALID | output | Output of the valid signal detector, enabled high if a valid RS-232 level is present on any receiver input. |
| 8 | T1IN | input | TTL/CMOS transmitter input with no pull-up resistor. |
| 9 | FORCEON | input | Drive high to override the automatic circuitry that keeps the transmitters and charge pump on (FORCEOFF must be high). |
| 10 | T1OUT | output | RS-232 transmitter output, protected to ±15kV ESD, high-impedance when shut down and able to be driven to ±12V in that state. |
| 11 | GND | power_in | Ground. |
| 12 | VCC | power_in | +3.0V to +5.5V supply voltage. |
| 13 | FORCEOFF | input | Active-low force-off input that, when driven low, shuts down the transmitters and the on-board charge pump, overriding all automatic circuitry and FORCEON. |
| 14 | EN | input | Receiver enable control: drive low for normal operation, drive high to force the receiver output (R1OUT) into a high-impedance state. |
| 15 | V+ | power_out | +5.5V generated by the charge pump. |
| 16 | C1+ | passive | Positive terminal of the voltage doubler charge-pump capacitor. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | TQFN-16(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
MAX3221EETE+ - Footprint:
Package_DFN_QFN:QFN-16-1EP_5x5mm_P0.8mm_EP2.7x2.7mm - 3D model: TQFN-16(5x5) (KiCad packages3D, STEP)
- 3D model files:
max3221eete-etched.step/max3221eete-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3221eete.step/max3221eete.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Maxim Integrated datasheet (19 pp, sha256
05825bd0ffbc0555, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MAX3221EETE+
**Maxim Integrated** · RS232 ICs · TQFN-16(5x5)
MAX3221EETE+ from Maxim Integrated, in a TQFN-16(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1- | passive | Negative terminal of the voltage doubler charge-pump capacitor. |
| 2 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 3 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 4 | V- | power_out | -5.5V generated by the charge pump. |
| 5 | R1IN | input | RS-232 receiver input, protected to ±15kV ESD and with an input voltage range of -25V to +25V. |
| 6 | R1OUT | tri_state | TTL/CMOS receiver output that goes high-impedance when EN is driven high. |
| 7 | INVALID | output | Output of the valid signal detector, enabled high if a valid RS-232 level is present on any receiver input. |
| 8 | T1IN | input | TTL/CMOS transmitter input with no pull-up resistor. |
| 9 | FORCEON | input | Drive high to override the automatic circuitry that keeps the transmitters and charge pump on (FORCEOFF must be high). |
| 10 | T1OUT | output | RS-232 transmitter output, protected to ±15kV ESD, high-impedance when shut down and able to be driven to ±12V in that state. |
| 11 | GND | power_in | Ground. |
| 12 | VCC | power_in | +3.0V to +5.5V supply voltage. |
| 13 | FORCEOFF | input | Active-low force-off input that, when driven low, shuts down the transmitters and the on-board charge pump, overriding all automatic circuitry and FORCEON. |
| 14 | EN | input | Receiver enable control: drive low for normal operation, drive high to force the receiver output (R1OUT) into a high-impedance state. |
| 15 | V+ | power_out | +5.5V generated by the charge pump. |
| 16 | C1+ | passive | Positive terminal of the voltage doubler charge-pump capacitor. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | TQFN-16(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 17 |
## CAD (KiCad official)
- Symbol: `MAX3221EETE+`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_5x5mm_P0.8mm_EP2.7x2.7mm`
- 3D model: TQFN-16(5x5) (KiCad packages3D, STEP)
- 3D model files: `max3221eete-etched.step` / `max3221eete-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `max3221eete.step` / `max3221eete.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Maxim Integrated datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/max3221e-max3243e.pdf) (19 pp, sha256 `05825bd0ffbc0555`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/max3221eete-datasheet.pdf)