component
M95160-RMN6TP
Public Made by Adomby adom
STMicroelectronics EEPROM, SO-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
M95160-RMN6TP
STMicroelectronics · EEPROM · SO-8
M95160-RMN6TP from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S | input | Chip Select: driven low to select the device and enter Active Power mode, driven high to deselect it (Serial Data Output Q goes high impedance and the device enters Standby Power mode unless a write cycle is in progress); a falling edge is required after power-up before any instruction. |
| 2 | Q | output | Serial Data Output: data is shifted out on the falling edge of Serial Clock C, and the output is high impedance when the device is deselected or in the Hold condition. |
| 3 | W | input | Write Protect: must be driven either high or low and kept stable during all Write instructions; with the SRWD bit set to 1 and W low, the Status Register is hardware write-protected. |
| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |
| 5 | D | input | Serial Data Input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock C. |
| 6 | C | input | Serial Clock: provides the timing of the serial interface, with instructions, addresses and data latched on its rising edge and output data changing from its falling edge; the M95160-R clock frequency is up to 5 MHz (Table 18). |
| 7 | HOLD | input | Hold: when driven low while the device is selected (S low) and C is low, serial communication is paused, Q goes high impedance, and D and C are don't care. |
| 8 | VCC | power_in | Supply voltage: for the M95160-R it must be within 1.8 V to 5.5 V and remain stable during instruction transmission and internal write cycles. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-8 |
| Category | Memory |
| Pins | 8 |
CAD (KiCad official)
- Symbol:
M95160-RMN6TP - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
m95160-rmn6tp-etched.step/m95160-rmn6tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m95160-rmn6tp.step/m95160-rmn6tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (53 pp, sha256
a67ad92b7c7416f4, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M95160-RMN6TP
**STMicroelectronics** · EEPROM · SO-8
M95160-RMN6TP from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S | input | Chip Select: driven low to select the device and enter Active Power mode, driven high to deselect it (Serial Data Output Q goes high impedance and the device enters Standby Power mode unless a write cycle is in progress); a falling edge is required after power-up before any instruction. |
| 2 | Q | output | Serial Data Output: data is shifted out on the falling edge of Serial Clock C, and the output is high impedance when the device is deselected or in the Hold condition. |
| 3 | W | input | Write Protect: must be driven either high or low and kept stable during all Write instructions; with the SRWD bit set to 1 and W low, the Status Register is hardware write-protected. |
| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |
| 5 | D | input | Serial Data Input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock C. |
| 6 | C | input | Serial Clock: provides the timing of the serial interface, with instructions, addresses and data latched on its rising edge and output data changing from its falling edge; the M95160-R clock frequency is up to 5 MHz (Table 18). |
| 7 | HOLD | input | Hold: when driven low while the device is selected (S low) and C is low, serial communication is paused, Q goes high impedance, and D and C are don't care. |
| 8 | VCC | power_in | Supply voltage: for the M95160-R it must be within 1.8 V to 5.5 V and remain stable during instruction transmission and internal write cycles. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-8 |
| Category | Memory |
| Pins | 8 |
## CAD (KiCad official)
- Symbol: `M95160-RMN6TP`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `m95160-rmn6tp-etched.step` / `m95160-rmn6tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m95160-rmn6tp.step` / `m95160-rmn6tp.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590227408873304064) (53 pp, sha256 `a67ad92b7c7416f4`, retrieved 2026-10-08, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m95160-rmn6tp-datasheet.pdf)