component
M95160-RMN6TP
Public Made by Adomby adom
STMicroelectronics EEPROM, SO-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+44@@ -0,0 +1,44 @@+# M95160-RMN6TP++**STMicroelectronics** · EEPROM · SO-8++M95160-RMN6TP from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | S | input | Chip Select: driven low to select the device and enter Active Power mode, driven high to deselect it (Serial Data Output Q goes high impedance and the device enters Standby Power mode unless a write cycle is in progress); a falling edge is required after power-up before any instruction. |+| 2 | Q | output | Serial Data Output: data is shifted out on the falling edge of Serial Clock C, and the output is high impedance when the device is deselected or in the Hold condition. |+| 3 | W | input | Write Protect: must be driven either high or low and kept stable during all Write instructions; with the SRWD bit set to 1 and W low, the Status Register is hardware write-protected. |+| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |+| 5 | D | input | Serial Data Input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock C. |+| 6 | C | input | Serial Clock: provides the timing of the serial interface, with instructions, addresses and data latched on its rising edge and output data changing from its falling edge; the M95160-R clock frequency is up to 5 MHz (Table 18). |+| 7 | HOLD | input | Hold: when driven low while the device is selected (S low) and C is low, serial communication is paused, Q goes high impedance, and D and C are don't care. |+| 8 | VCC | power_in | Supply voltage: for the M95160-R it must be within 1.8 V to 5.5 V and remain stable during instruction transmission and internal write cycles. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SO-8 |+| Category | Memory |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `M95160-RMN6TP`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SO-8 (KiCad packages3D, STEP)+- 3D model files: `m95160-rmn6tp-etched.step` / `m95160-rmn6tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m95160-rmn6tp.step` / `m95160-rmn6tp.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590227408873304064) (53 pp, sha256 `a67ad92b7c7416f4`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/m95160-rmn6tp-datasheet.pdf)
page.jsonadded+200@@ -0,0 +1,200 @@+{+ "slug": "m95160-rmn6tp",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics EEPROM, SO-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "memory",+ "m95160-rmn6tp",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "m95160-rmn6tp.kicad_sym",+ "m95160-rmn6tp.kicad_mod",+ "m95160-rmn6tp.glb",+ "m95160-rmn6tp.step",+ "m95160-rmn6tp.lbr",+ "docs/hero.png",+ "docs/m95160-rmn6tp-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "m95160-rmn6tp-hero.glb",+ "m95160-rmn6tp-hero.overlay.json"+ ],+ "component": {+ "mpn": "M95160-RMN6TP",+ "manufacturer": "STMicroelectronics",+ "package": "SO-8",+ "pin_count": 8,+ "category": "Memory",+ "subcategory": "EEPROM",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590227408873304064",+ "parts": {+ "symbol": "m95160-rmn6tp.kicad_sym",+ "footprint": "m95160-rmn6tp.kicad_mod",+ "model_3d": "m95160-rmn6tp-hero.glb",+ "model_3d_plain": "m95160-rmn6tp.glb",+ "model_3d_step": "m95160-rmn6tp-etched.step",+ "model_3d_step_plain": "m95160-rmn6tp.step",+ "lbr": "m95160-rmn6tp.lbr"+ },+ "distributor_links": {+ "lcsc": "C2970232",+ "digikey": "497-8688-2-ND",+ "mouser": "511-M95160-RMN6TP"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T03:43:21Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-8688-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "511-M95160-RMN6TP",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "S",+ "type": "input",+ "description": "Chip Select: driven low to select the device and enter Active Power mode, driven high to deselect it (Serial Data Output Q goes high impedance and the device enters Standby Power mode unless a write cycle is in progress); a falling edge is required after power-up before any instruction."+ },+ {+ "number": "2",+ "name": "Q",+ "type": "output",+ "description": "Serial Data Output: data is shifted out on the falling edge of Serial Clock C, and the output is high impedance when the device is deselected or in the Hold condition."+ },+ {+ "number": "3",+ "name": "W",+ "type": "input",+ "description": "Write Protect: must be driven either high or low and kept stable during all Write instructions; with the SRWD bit set to 1 and W low, the Status Register is hardware write-protected."+ },+ {+ "number": "4",+ "name": "VSS",+ "type": "power_in",+ "description": "Ground: the reference for all signals, including the VCC supply voltage."+ },+ {+ "number": "5",+ "name": "D",+ "type": "input",+ "description": "Serial Data Input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock C."+ },+ {+ "number": "6",+ "name": "C",+ "type": "input",+ "description": "Serial Clock: provides the timing of the serial interface, with instructions, addresses and data latched on its rising edge and output data changing from its falling edge; the M95160-R clock frequency is up to 5 MHz (Table 18)."+ },+ {+ "number": "7",+ "name": "HOLD",+ "type": "input",+ "description": "Hold: when driven low while the device is selected (S low) and C is low, serial communication is paused, Q goes high impedance, and D and C are don't care."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Supply voltage: for the M95160-R it must be within 1.8 V to 5.5 V and remain stable during instruction transmission and internal write cycles."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet's Figure 2 (8-pin package connections, top view) is an image and its pin numbers did n; The datasheet covers several variants (M95160-W, -R, -DF). The M95160-RMN6TP uses the M95160-R opera; The datasheet gives no separate pinout for the MN (SO8N) package beyond Figure 2, and the package me"+ ],+ "pages_sent": 53,+ "cost_usd": 0.426,+ "at": "2026-10-08T03:43:06"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590227408873304064",+ "pages": 53,+ "sha256": "a67ad92b7c7416f4",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "m95160-rmn6tp.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "m95160-rmn6tp-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "ad26ee8d29ab98493b8c8c851070f6b6a40ac1c2501466ba68f59c62be859853",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}