3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗PCB Footprint
Open full view ↗Datasheet
Open in new tab ↗Contents
README
markdownM95160-DRDW3TP
The maker sells this part only as M95160-DRDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 19, p.40)). The DigiKey and Mouser numbers on this page are for M95160-DRDW3TP/K.
STMicroelectronics · EEPROM · TSSOP-8
M95160-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S | input | Chip Select, active low: driving it low selects the device and starts communication, driving it high deselects the device and puts Q in high impedance. |
| 2 | Q | tri_state | Serial Data output, shifts data out on the falling edge of C, MSB first, and is high impedance in all other cases. |
| 3 | W | input | Write Protect, active low, used to write-protect the Status Register. |
| 4 | VSS | power_in | Ground, the reference for all signals including the VCC supply voltage. |
| 5 | D | input | Serial Data input, receives instructions, addresses and data to be written, latched on the rising edge of C, MSB first. |
| 6 | C | input | Serial Clock, synchronizes the serial interface, with inputs latched on the rising edge and Q changing after the falling edge, up to 20 MHz for VCC ≥ 4.5 V. |
| 7 | HOLD | input | Hold, active low, pauses serial communication without deselecting the device or resetting the clocking sequence. |
| 8 | VCC | power_in | Supply voltage, 1.7 V to 5.5 V for voltage range R (up to 125 °C); decouple with 10 nF to 100 nF close to VCC/VSS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | TSTG | -65 | 150 | °C | 28 | ||
| Ambient operating temperature | TAMR | -40 | 150 | °C | 28 | ||
| Voltage on Q pin | VO | -0.5 | V | max printed as VCC+0.6 V | 28 | ||
| Input voltage | VI | -0.5 | 6.5 | V | 28 | ||
| DC output current (Q = 0) | IOL | 5 | mA | 28 | |||
| DC output current (Q = 1) | IOH | 5 | mA | 28 | |||
| Supply voltage | VCC | -0.5 | 6.5 | V | 28 | ||
| Electrostatic pulse (Human Body Model) | VESD | 4000 | V | AEC-Q100-002, C1=100 pF, R1=1500 Ω, R2=500 Ω | 28 | ||
| Write cycle endurance | Ncycle | 4e+06 | Write cycle | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 29 | ||
| Write cycle endurance | Ncycle | 1.2e+06 | Write cycle | TA = 85 °C, 1.7 V < VCC < 5.5 V | 29 | ||
| Write cycle endurance | Ncycle | 600000 | Write cycle | TA = 125 °C, 1.7 V < VCC < 5.5 V | 29 | ||
| Supply voltage | VCC | 1.7 | 5.5 | V | 29 | ||
| Ambient operating temperature | TA | -40 | 125 | °C | 29 | ||
| Operating clock frequency | fC | 10 | MHz | VCC ≥ 2.5 V, capacitive load on Q pin ≤100pF | 29 | ||
| Operating clock frequency | fC | 5 | MHz | VCC ≥ 1.7 V, capacitive load on Q pin ≤100pF | 29 | ||
| Output capacitance (Q) | COUT | 8 | pF | VOUT = 0 V | 31 | ||
| Input capacitance | CIN | 6 | pF | VIN = 0 V | 31 | ||
| Input leakage current | ILI | 2 | µA | VIN = VSS or VCC | 31 | ||
| Output leakage current | ILO | 3 | µA | S = VCC, VOUT = VSS or VCC | 31 | ||
| Supply current (Read) | ICC | 2 | mA | VCC = 1.7 V, C = 0.1 VCC/0.9 VCC, Q = open, fC = 5 MHz | 31 | ||
| Supply current (Read) | ICC | 5 | mA | VCC = 5.5 V, fC = 20 MHz, C = 0.1 VCC/0.9 VCC, Q = open; -40 °C < t° < 85 °C | 31 | ||
| Supply current (Write) | ICC0 | 2 | mA | 1.7 V ≤ VCC < 5.5 V during tW, S = VCC; average value during write cycle | 31 | ||
| Supply current (Standby mode) | ICC1 | 1 | µA | t° = 85 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 31 | ||
| Supply current (Standby mode) | ICC1 | 2 | µA | t° = 85 °C, VCC = 2.5 V, S = VCC, VIN = VSS or VCC | 31 | ||
| Supply current (Standby mode) | ICC1 | 3 | µA | t° = 85 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 31 | ||
| Supply current (Standby mode) | ICC1 | 15 | µA | t° = 125 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 31 | ||
| Supply current (Standby mode) | ICC1 | 20 | µA | t° = 125 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 31 | ||
| Input low voltage | VIL | -0.45 | 0.25 | V | 1.7 V ≤ VCC < 2.5 V; max printed as 0.25 VCC | 31 | |
| Input low voltage | VIL | -0.45 | 0.3 | V | 2.5 V ≤ VCC < 5.5 V; max printed as 0.3 VCC | 31 | |
| Input high voltage | VIH | 0.75 | V | 1.7 V ≤ VCC < 2.5 V; min printed as 0.75 VCC, max printed as VCC+1 | 31 | ||
| Input high voltage | VIH | 0.7 | V | 2.5 V ≤ VCC < 5.5 V; min printed as 0.7 VCC, max printed as VCC+1 | 31 | ||
| Output low voltage | VOL | 0.3 | V | VCC = 1.7 V, IOL = 1 mA | 31 | ||
| Output low voltage | VOL | 0.4 | V | VCC ≥ 2.5 V, IOL = 2 mA | 31 | ||
| Output high voltage | VOH | 0.8 | V | VCC = 1.7 V, IOH = 1 mA; min printed as 0.8 VCC | 31 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 31 | ||
| Clock frequency | fC | 5 | MHz | Test conditions specified in Table 11 | 32 | ||
| S active setup time | tSLCH | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| S not active setup time | tSHCH | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| S deselect time | tSHSL | 90 | ns | Test conditions specified in Table 11 | 32 | ||
| S active hold time | tCHSH | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| S not active hold time | tCHSL | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| Clock high time | tCH | 80 | ns | Test conditions specified in Table 11 | 32 | ||
| Clock low time | tCL | 80 | ns | Test conditions specified in Table 11 | 32 | ||
| Clock rise time | tCLCH | 2 | µs | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| Clock fall time | tCHCL | 2 | µs | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| Data in setup time | tDVCH | 20 | ns | Test conditions specified in Table 11 | 32 | ||
| Data in hold time | tCHDX | 20 | ns | Test conditions specified in Table 11 | 32 | ||
| Clock low hold time after HOLD not active | tHHCH | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| Clock low hold time after HOLD active | tHLCH | 60 | ns | Test conditions specified in Table 11 | 32 | ||
| Output disable time | tSHQZ | 80 | ns | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| Clock low to output valid | tCLQV | 80 | ns | Test conditions specified in Table 11 | 32 | ||
| Output hold time | tCLQX | 0 | ns | Test conditions specified in Table 11 | 32 | ||
| Output rise time | tQLQH | 20 | ns | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| Output fall time | tQHQL | 20 | ns | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| HOLD high to output valid | tHHQV | 80 | ns | Test conditions specified in Table 11 | 32 | ||
| HOLD low to output high-Z | tHLQZ | 80 | ns | Test conditions specified in Table 11; value guaranteed by characterization | 32 | ||
| Write time | tW | 4 | ms | Test conditions specified in Table 11 | 32 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering See note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 28 |
CAD (KiCad official)
- Symbol:
M95160-DRDW3TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m95160-drdw3tp-etched.step/m95160-drdw3tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m95160-drdw3tp.step/m95160-drdw3tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (43 pp, sha256
49916e39586de793, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).