main
History Download
Ray Publish 0.1.0 28218c6

M93C86-WDW6TP

STMicroelectronics · EEPROM · TSSOP-8

M93C86-WDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 S input Chip Select input; an instruction starts on a rising edge of S with C held low, and S must be driven to VSS (e.g. via a pull-down) during power-up.
2 C input Serial Clock input; clock frequency is DC to 2 MHz and C must be held low when S rises.
3 D input Serial Data input, sampled on the rising edge of Serial Clock C for the start bit, op-code, address and data bits.
4 Q output Serial Data output, which shifts out read data on rising edges of C and gives READY/BUSY status (Q=0 busy, Q=1 ready) during write or erase cycles; it is Hi-Z when the device is deselected.
5 VSS power_in Ground reference for the device.
6 ORG input Organization Select; connected to VSS selects x8, left unconnected or connected to VCC selects x16, and it should be tied to VSS or VCC in standby to minimize standby current.
7 DU unconnected Don't Use pin reserved for ST test sequences; it may be left unconnected or connected to VCC or VSS.
8 VCC power_in Supply voltage of 2.5 V to 5.5 V for the M93C86-W, which should be decoupled with 10 nF to 100 nF close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient operating temperature -40 130 °C 19
Storage temperature TSTG -65 150 °C 19
Output range (Q = VOH or Hi-Z), lower limit VOUT -0.5 V Q = VOH or Hi-Z 19
Input range, lower limit VIN -0.5 V 19
Supply voltage VCC -0.5 6.5 V 19
Electrostatic discharge voltage (human body model) VESD 4000 V Human body model 19
Supply voltage (M93Cx6-W) VCC 2.5 5.5 V M93Cx6-W 20
Ambient operating temperature (device grade 6) TA -40 85 °C 20
Write cycle endurance Ncycle 4e+06 TA ≤ 25 °C, VCC(min) < VCC < VCC(max) 20
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, VCC(min) < VCC < VCC(max) 20
Data retention 200 Year TA = 55 °C 20
Input rise and fall times 50 ns 20
Input voltage levels 0.2 0.8 VCC 20
Input timing reference voltages 0.3 0.7 VCC 20
Output timing reference voltages 0.3 0.7 VCC 20
Output capacitance COUT 8 pF VOUT = 0V 21
Input capacitance CIN 6 pF VIN = 0V 21
Input leakage current ILI -2.5 2.5 µA 0V ≤ VIN ≤ VCC 21
Output leakage current ILO -2.5 2.5 µA 0V ≤ VOUT ≤ VCC, Q in Hi-Z 21
Operating supply current ICC 2 mA VCC = 5 V, S = VIH, f = 2 MHz, Q = open 21
Operating supply current ICC 1 mA VCC = 2.5 V, S = VIH, f = 2 MHz, Q = open 21
Standby supply current ICC1 2 µA VCC = 2.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z 21
Standby supply current ICC1 3 µA VCC = 5.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z 21
Input low voltage (D, C, S), lower limit VIL -0.45 V 21
Input low voltage (D, C, S), upper limit VIL 0.2 VCC 21
Input high voltage (D, C, S), lower limit VIH 0.7 VCC 21
Input high voltage (D, C, S), upper limit VIH 1 V 21
Output low voltage (Q) VOL 0.4 V VCC = 5 V, IOL = 2.1 mA 21
Output low voltage (Q) VOL 0.2 V VCC = 2.5 V, IOL = 100 µA 21
Output high voltage (Q) VOH 0.8 VCC VCC = 5 V, IOH = -400 µA 21
Output high voltage (Q) VOH -0.2 V VCC = 2.5 V, IOH = -100 µA 21
Maximum clock frequency fC 2 MHz 22
Chip Select low to Clock high tSLCH 50 ns 22
Chip Select setup time tSHCH 50 ns 22
Chip Select low to Chip Select high tSLSH 200 ns 22
Clock high time tCHCL 200 ns 22
Clock low time tCLCH 200 ns 22
Data in setup time tDVCH 50 ns 22
Data in hold time tCHDX 50 ns 22
Clock setup time (relative to S) tCLSH 50 ns 22
Chip Select hold time tCLSL 0 ns 22
Chip Select to READY/BUSY status tSHQV 200 ns 22
Chip Select low to output Hi-Z tSLQZ 100 ns 22
Delay to output low tCHQL 200 ns 22
Delay to output valid tCHQV 200 ns 22
Erase or Write cycle time tW 5 ms 22

CAD (KiCad official)

  • Symbol: M93C86-WDW6TP
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m93c86-wdw6tp-etched.step / m93c86-wdw6tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m93c86-wdw6tp.step / m93c86-wdw6tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (35 pp, sha256 7b1f76e6c602697a, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF