Generated by kicad-footprint-generator · KiCad file format 20260206
M93C86-WDW6TP
STMicroelectronics · EEPROM · TSSOP-8
M93C86-WDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S | input | Chip Select input; an instruction starts on a rising edge of S with C held low, and S must be driven to VSS (e.g. via a pull-down) during power-up. |
| 2 | C | input | Serial Clock input; clock frequency is DC to 2 MHz and C must be held low when S rises. |
| 3 | D | input | Serial Data input, sampled on the rising edge of Serial Clock C for the start bit, op-code, address and data bits. |
| 4 | Q | output | Serial Data output, which shifts out read data on rising edges of C and gives READY/BUSY status (Q=0 busy, Q=1 ready) during write or erase cycles; it is Hi-Z when the device is deselected. |
| 5 | VSS | power_in | Ground reference for the device. |
| 6 | ORG | input | Organization Select; connected to VSS selects x8, left unconnected or connected to VCC selects x16, and it should be tied to VSS or VCC in standby to minimize standby current. |
| 7 | DU | unconnected | Don't Use pin reserved for ST test sequences; it may be left unconnected or connected to VCC or VSS. |
| 8 | VCC | power_in | Supply voltage of 2.5 V to 5.5 V for the M93C86-W, which should be decoupled with 10 nF to 100 nF close to the VCC/VSS pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient operating temperature | -40 | 130 | °C | 19 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 19 | ||
| Output range (Q = VOH or Hi-Z), lower limit | VOUT | -0.5 | V | Q = VOH or Hi-Z | 19 | ||
| Input range, lower limit | VIN | -0.5 | V | 19 | |||
| Supply voltage | VCC | -0.5 | 6.5 | V | 19 | ||
| Electrostatic discharge voltage (human body model) | VESD | 4000 | V | Human body model | 19 | ||
| Supply voltage (M93Cx6-W) | VCC | 2.5 | 5.5 | V | M93Cx6-W | 20 | |
| Ambient operating temperature (device grade 6) | TA | -40 | 85 | °C | 20 | ||
| Write cycle endurance | Ncycle | 4e+06 | TA ≤ 25 °C, VCC(min) < VCC < VCC(max) | 20 | |||
| Write cycle endurance | Ncycle | 1.2e+06 | TA = 85 °C, VCC(min) < VCC < VCC(max) | 20 | |||
| Data retention | 200 | Year | TA = 55 °C | 20 | |||
| Input rise and fall times | 50 | ns | 20 | ||||
| Input voltage levels | 0.2 | 0.8 | VCC | 20 | |||
| Input timing reference voltages | 0.3 | 0.7 | VCC | 20 | |||
| Output timing reference voltages | 0.3 | 0.7 | VCC | 20 | |||
| Output capacitance | COUT | 8 | pF | VOUT = 0V | 21 | ||
| Input capacitance | CIN | 6 | pF | VIN = 0V | 21 | ||
| Input leakage current | ILI | -2.5 | 2.5 | µA | 0V ≤ VIN ≤ VCC | 21 | |
| Output leakage current | ILO | -2.5 | 2.5 | µA | 0V ≤ VOUT ≤ VCC, Q in Hi-Z | 21 | |
| Operating supply current | ICC | 2 | mA | VCC = 5 V, S = VIH, f = 2 MHz, Q = open | 21 | ||
| Operating supply current | ICC | 1 | mA | VCC = 2.5 V, S = VIH, f = 2 MHz, Q = open | 21 | ||
| Standby supply current | ICC1 | 2 | µA | VCC = 2.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z | 21 | ||
| Standby supply current | ICC1 | 3 | µA | VCC = 5.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z | 21 | ||
| Input low voltage (D, C, S), lower limit | VIL | -0.45 | V | 21 | |||
| Input low voltage (D, C, S), upper limit | VIL | 0.2 | VCC | 21 | |||
| Input high voltage (D, C, S), lower limit | VIH | 0.7 | VCC | 21 | |||
| Input high voltage (D, C, S), upper limit | VIH | 1 | V | 21 | |||
| Output low voltage (Q) | VOL | 0.4 | V | VCC = 5 V, IOL = 2.1 mA | 21 | ||
| Output low voltage (Q) | VOL | 0.2 | V | VCC = 2.5 V, IOL = 100 µA | 21 | ||
| Output high voltage (Q) | VOH | 0.8 | VCC | VCC = 5 V, IOH = -400 µA | 21 | ||
| Output high voltage (Q) | VOH | -0.2 | V | VCC = 2.5 V, IOH = -100 µA | 21 | ||
| Maximum clock frequency | fC | 2 | MHz | 22 | |||
| Chip Select low to Clock high | tSLCH | 50 | ns | 22 | |||
| Chip Select setup time | tSHCH | 50 | ns | 22 | |||
| Chip Select low to Chip Select high | tSLSH | 200 | ns | 22 | |||
| Clock high time | tCHCL | 200 | ns | 22 | |||
| Clock low time | tCLCH | 200 | ns | 22 | |||
| Data in setup time | tDVCH | 50 | ns | 22 | |||
| Data in hold time | tCHDX | 50 | ns | 22 | |||
| Clock setup time (relative to S) | tCLSH | 50 | ns | 22 | |||
| Chip Select hold time | tCLSL | 0 | ns | 22 | |||
| Chip Select to READY/BUSY status | tSHQV | 200 | ns | 22 | |||
| Chip Select low to output Hi-Z | tSLQZ | 100 | ns | 22 | |||
| Delay to output low | tCHQL | 200 | ns | 22 | |||
| Delay to output valid | tCHQV | 200 | ns | 22 | |||
| Erase or Write cycle time | tW | 5 | ms | 22 |
CAD (KiCad official)
- Symbol:
M93C86-WDW6TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m93c86-wdw6tp-etched.step/m93c86-wdw6tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m93c86-wdw6tp.step/m93c86-wdw6tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (35 pp, sha256
7b1f76e6c602697a, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).