main
Ray m93c66-rmn3tp: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) cae52cc
{
  "slug": "m93c66-rmn3tp",
  "version": "0.1.0",
  "type": "component",
  "description": "STMicroelectronics EEPROM, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "memory",
    "m93c66-rmn3tp"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "m93c66-rmn3tp.kicad_sym",
    "m93c66-rmn3tp.kicad_mod",
    "m93c66-rmn3tp.glb",
    "m93c66-rmn3tp.step",
    "m93c66-rmn3tp.lbr",
    "docs/hero.png",
    "docs/m93c66-rmn3tp-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "m93c66-rmn3tp-etched.step"
  ],
  "visibility": {
    "public": true
  },
  "author": {
    "name": "Ray"
  },
  "component": {
    "mpn": "M93C66-RMN3TP",
    "manufacturer": "STMicroelectronics",
    "package": "SOIC-8",
    "pin_count": 8,
    "category": "EEPROM",
    "datasheet": "https://www.st.com/resource/en/datasheet/m93c66-rmn3tp.pdf",
    "parts": {
      "symbol": "m93c66-rmn3tp.kicad_sym",
      "footprint": "m93c66-rmn3tp.kicad_mod",
      "model_3d": "m93c66-rmn3tp-etched.glb",
      "model_3d_plain": "m93c66-rmn3tp.glb",
      "model_3d_step": "m93c66-rmn3tp-etched.step",
      "model_3d_step_plain": "m93c66-rmn3tp.step",
      "lbr": "m93c66-rmn3tp.lbr"
    },
    "pins": [
      {
        "number": "1",
        "name": "S",
        "type": "input",
        "description": "Chip Select input. Active High; enables the device and frames each MICROWIRE instruction. Must be pulled to VSS at power-up (recommended external pull-down, typ. 100 kΩ) to prevent inadvertent selection."
      },
      {
        "number": "2",
        "name": "C",
        "type": "input",
        "description": "Serial Clock input. Synchronous clock driven by the bus master; latches D on rising edges and shifts Q out. Maximum clock rate 2 MHz. External pull-down recommended so that C is low when S is deselected (meets tSLCH)."
      },
      {
        "number": "3",
        "name": "D",
        "type": "input",
        "description": "Serial Data input. Carries the start bit, op-code, address, and write data for MICROWIRE instructions; sampled on the rising edge of C while S is High."
      },
      {
        "number": "4",
        "name": "Q",
        "type": "tri_state",
        "description": "Serial Data output. Push-pull output that shifts read data out on the rising edge of C; also drives the READY/BUSY status during a programming cycle when S is High. Goes high-impedance when the device is deselected."
      },
      {
        "number": "5",
        "name": "VSS",
        "type": "power_in",
        "description": "Ground reference (0 V). Common return for supply and all logic signals."
      },
      {
        "number": "6",
        "name": "ORG",
        "type": "input",
        "description": "Organization Select input. Tie to VCC (or leave open - internally pulled up) to configure the array as 256 x 16; tie to VSS to configure as 512 x 8. Must be driven to VCC or VSS (not left mid-rail) in Standby to minimize ICC."
      },
      {
        "number": "7",
        "name": "DU",
        "type": "unconnected",
        "description": "Don't Use. Reserved for STMicroelectronics test purposes and must not be used in normal operation. May be left unconnected or tied to VCC or VSS."
      },
      {
        "number": "8",
        "name": "VCC",
        "type": "power_in",
        "description": "Positive supply input, 1.8 V to 5.5 V. Decouple to VSS with a 10-100 nF capacitor close to the pin; must remain stable through the internal write cycle (tW)."
      }
    ],
    "provenance": {
      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "distributor_links": {
      "digikey": false,
      "mouser": false
    },
    "distributor_check": {
      "checked_at": "2026-10-05T19:07:05Z",
      "source": "Component Ocean /api/assign-pns + lcsc_map",
      "digikey": {
        "pn": null,
        "status": "no match"
      },
      "mouser": {
        "pn": null,
        "status": "no match"
      }
    },
    "models_3d": [
      {
        "file": "m93c66-rmn3tp.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6,
          4.9,
          1.75
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "m93c66-rmn3tp-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6,
          4.9,
          1.75
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "c94e12c1d61e71525835baa67abc1972aca6a2aaddbee98e381e76f104978d9c",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}