main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs m93c66-rmn3tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers m93c66-rmn3tp: viewers · Ray
m93c66-rmn3tp-etched.fit.json m93c66-rmn3tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m93c66-rmn3tp-etched.glb m93c66-rmn3tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m93c66-rmn3tp-etched.step m93c66-rmn3tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m93c66-rmn3tp.glb Publish 0.1.0 · Ray
m93c66-rmn3tp.kicad_mod Publish 0.1.0 · Ray
m93c66-rmn3tp.kicad_sym Publish 0.1.0 · Ray
m93c66-rmn3tp.lbr Publish 0.1.0 · Ray
m93c66-rmn3tp.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json m93c66-rmn3tp: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md m93c66-rmn3tp: laser-etched CAD + chip hero (factory 2.0.0 backfill) · Ray

M93C66-RMN3TP

STMicroelectronics · EEPROM · SOIC-8

M93C66-RMN3TP from STMicroelectronics, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 S input Chip Select input. Active High; enables the device and frames each MICROWIRE instruction. Must be pulled to VSS at power-up (recommended external pull-down, typ. 100 kΩ) to prevent inadvertent selection.
2 C input Serial Clock input. Synchronous clock driven by the bus master; latches D on rising edges and shifts Q out. Maximum clock rate 2 MHz. External pull-down recommended so that C is low when S is deselected (meets tSLCH).
3 D input Serial Data input. Carries the start bit, op-code, address, and write data for MICROWIRE instructions; sampled on the rising edge of C while S is High.
4 Q tri_state Serial Data output. Push-pull output that shifts read data out on the rising edge of C; also drives the READY/BUSY status during a programming cycle when S is High. Goes high-impedance when the device is deselected.
5 VSS power_in Ground reference (0 V). Common return for supply and all logic signals.
6 ORG input Organization Select input. Tie to VCC (or leave open - internally pulled up) to configure the array as 256 x 16; tie to VSS to configure as 512 x 8. Must be driven to VCC or VSS (not left mid-rail) in Standby to minimize ICC.
7 DU unconnected Don't Use. Reserved for STMicroelectronics test purposes and must not be used in normal operation. May be left unconnected or tied to VCC or VSS.
8 VCC power_in Positive supply input, 1.8 V to 5.5 V. Decouple to VSS with a 10-100 nF capacitor close to the pin; must remain stable through the internal write cycle (tW).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SOIC-8
Category Memory
Pins 8

Ordering variants

  • M93C66-RMN3TP
  • M93C66-RMN3TPDW
  • M93C66-RMN3TPMF

CAD (KiCad official)

  • Symbol: M93C66-RMN3TP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: m93c66-rmn3tp-etched.step / m93c66-rmn3tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m93c66-rmn3tp.step / m93c66-rmn3tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (None pp, sha256 ea011e1cc0d30be7, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF