main
Ray
Publish 0.1.0
a385cb6
M25P20-VMN6TPB
Micron Tech · NOR FLASH · SO-8
M25P20-VMN6TPB from Micron Tech, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S# | input | Chip select: when HIGH the device is deselected and DQ1 is high-impedance, and a falling edge on S# is required before any command after power-up (page 8). |
| 2 | DQ1 | bidirectional | Serial data output, shifting data out on the falling edge of C; it is high-impedance when S# is HIGH or during a hold condition (page 8). |
| 3 | W# | input | Write protect: freezes the size of the memory area protected against WRITE, PROGRAM and ERASE as set by the block protect bits in the status register (page 8). |
| 4 | VSS | power_in | Ground: reference for the VCC supply voltage (page 8). |
| 5 | DQ0 | bidirectional | Serial data input: commands, addresses and program data are latched on the rising edge of C (page 8). |
| 6 | C | input | Serial clock: provides the timing of the serial interface, with maximum clock frequency of 75 MHz on VCC 2.7V-3.6V (pages 6 and 8). |
| 7 | HOLD# | input | Hold: pauses serial communication without deselecting the device, with DQ1 high-impedance and DQ0 and C treated as don't care; the device must be selected with S# LOW to start a hold (page 8). |
| 8 | VCC | power_in | Device core power supply; operating voltage is 2.3V to 3.6V for this part (page 8 and page 44). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Micron Tech |
| Package | SO-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input leakage current | ILI | -2 | 2 | µA | 36 | ||
| Output leakage current | ILO | -2 | 2 | µA | 36 | ||
| Standby current | ICC1 | 50 | µA | S# = VCC, VIN = VSS or VCC | 36 | ||
| Deep power-down current | ICC2 | 5 | µA | S# = VCC, VIN = VSS or VCC | 36 | ||
| Operating current (READ) | ICC3 | 8 | mA | C = 0.1VCC / 0.9VCC at 40 MHz and 75 MHz, DQ1 = open | 36 | ||
| Operating current (READ) | ICC3 | 4 | mA | C = 0.1VCC / 0.9VCC at 20 MHz, DQ1 = open | 36 | ||
| Operating current (PAGE PROGRAM) | ICC4 | 15 | mA | S# = VCC | 36 | ||
| Operating current (WRITE STATUS REGISTER) | ICC5 | 15 | mA | S# = VCC | 36 | ||
| Operating current (SECTOR ERASE) | ICC6 | 15 | mA | S# = VCC | 36 | ||
| Operating current (BULK ERASE) | ICC7 | 15 | mA | S# = VCC | 36 | ||
| Input LOW voltage | VIL | -0.5 | V | 36 | |||
| Output LOW voltage | VOL | 0.4 | V | IOL = 1.6mA | 37 | ||
| WRITE STATUS REGISTER cycle time | tW | 1.3 | 15 | ms | Device grade 6 | 37 | |
| PAGE PROGRAM cycle time (256 bytes) | tPP | 0.8 | 5 | ms | Device grade 6, 256 bytes | 37 | |
| SECTOR ERASE cycle time | tSE | 0.6 | 3 | s | Device grade 6 | 37 | |
| BULK ERASE cycle time | tBE | 2.5 | 6 | s | Device grade 6 | 37 | |
| VCC(min) to S# LOW | tVSL | 10 | µs | Device grade 6 | 34 | ||
| Time delay to write instruction | tPUW | 1 | 10 | ms | Device grade 6 | 34 | |
| Write Inhibit voltage | VWI | 1 | 2.1 | V | Device grade 6 | 34 | |
| Supply voltage (operating) | VCC | 2.3 | 3.6 | V | 35 | ||
| Ambient operating temperature (grade 6) | TA | -40 | 85 | °C | Grade 6 | 35 | |
| Storage temperature | TSTG | -65 | 150 | °C | 35 | ||
| Input and output voltage (with respect to ground) | VIO | -0.6 | V | 35 | |||
| Supply voltage | VCC | -0.6 | 4 | V | 35 | ||
| Electrostatic discharge voltage (Human Body model) | VESD | -2000 | 2000 | V | JEDEC JESD22-A114A | 35 | |
| Program/Erase cycles | 100000 | cycles | Cycles per sector, grade 6 | 35 | |||
| Data retention | 20 | years | At 55°C | 35 | |||
| Output capacitance (DQ1) | COUT | 8 | pF | VOUT = 0 V | 38 | ||
| Input capacitance (other pins) | CIN | 6 | pF | VIN = 0 V | 38 | ||
| Load capacitance | CL | 30 | 30 | pF | AC measurement conditions | 38 | |
| Input rise and fall times | 5 | ns | AC measurement conditions | 38 | |||
| Clock frequency for all commands (except READ) | fC | 75 | MHz | VCCmin = 2.7V | 39 | ||
| Clock frequency for READ command | fR | 33 | MHz | VCCmin = 2.7V | 39 | ||
| Clock HIGH time | tCH | 6 | ns | VCCmin = 2.7V | 39 | ||
| Clock LOW time | tCL | 6 | ns | VCCmin = 2.7V | 39 | ||
| Clock rise time (peak-to-peak) | tCLCH | 0.1 | V/ns | VCCmin = 2.7V | 39 | ||
| Clock fall time (peak-to-peak) | tCHCL | 0.1 | V/ns | VCCmin = 2.7V | 39 | ||
| S# active setup time (relative to C) | tSLCH | 5 | ns | VCCmin = 2.7V | 39 | ||
| S# not active hold time (relative to C) | tCHSL | 5 | ns | VCCmin = 2.7V | 39 | ||
| Data In setup time | tDVCH | 2 | ns | VCCmin = 2.7V | 39 | ||
| Data In hold time | tCHDX | 5 | ns | VCCmin = 2.7V | 39 | ||
| S# active hold time (relative to C) | tCHSH | 5 | ns | VCCmin = 2.7V | 39 | ||
| S# not active setup time (relative to C) | tSHCH | 5 | ns | VCCmin = 2.7V | 39 | ||
| S# deselect time | tSHSL | 100 | ns | VCCmin = 2.7V | 39 | ||
| Output disable time | tSHQZ | 8 | ns | VCCmin = 2.7V | 39 | ||
| Output hold time | tCLQX | 0 | ns | VCCmin = 2.7V | 39 | ||
| HOLD# setup time (relative to C) | tHLCH | 5 | ns | VCCmin = 2.7V | 39 | ||
| HOLD# hold time (relative to C) | tCHHH | 5 | ns | VCCmin = 2.7V | 39 | ||
| HOLD# to output Low-Z | tHHQX | 8 | ns | VCCmin = 2.7V | 39 | ||
| HOLD# to output High-Z | tHLQZ | 8 | ns | VCCmin = 2.7V | 39 | ||
| WRITE PROTECT setup time | tWHSL | 20 | ns | VCCmin = 2.7V | 39 | ||
| WRITE PROTECT hold time | tSHWL | 100 | ns | VCCmin = 2.7V | 39 | ||
| S# HIGH to deep power-down mode | tDP | 3 | µs | VCCmin = 2.7V | 39 | ||
| S# HIGH to STANDBY without READ ELECTRONIC SIGNATURE | tRES1 | 30 | µs | VCCmin = 2.7V | 39 | ||
| S# HIGH to STANDBY with READ ELECTRONIC SIGNATURE | tRES2 | 30 | µs | VCCmin = 2.7V | 39 |
CAD (KiCad official)
- Symbol:
M25P20-VMN6TPB - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
m25p20-vmn6tpb-etched.step/m25p20-vmn6tpb-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m25p20-vmn6tpb.step/m25p20-vmn6tpb.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Micron Tech datasheet (46 pp, sha256
1b298df2f2fdd036, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M25P20-VMN6TPB
**Micron Tech** · NOR FLASH · SO-8
M25P20-VMN6TPB from Micron Tech, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S# | input | Chip select: when HIGH the device is deselected and DQ1 is high-impedance, and a falling edge on S# is required before any command after power-up (page 8). |
| 2 | DQ1 | bidirectional | Serial data output, shifting data out on the falling edge of C; it is high-impedance when S# is HIGH or during a hold condition (page 8). |
| 3 | W# | input | Write protect: freezes the size of the memory area protected against WRITE, PROGRAM and ERASE as set by the block protect bits in the status register (page 8). |
| 4 | VSS | power_in | Ground: reference for the VCC supply voltage (page 8). |
| 5 | DQ0 | bidirectional | Serial data input: commands, addresses and program data are latched on the rising edge of C (page 8). |
| 6 | C | input | Serial clock: provides the timing of the serial interface, with maximum clock frequency of 75 MHz on VCC 2.7V-3.6V (pages 6 and 8). |
| 7 | HOLD# | input | Hold: pauses serial communication without deselecting the device, with DQ1 high-impedance and DQ0 and C treated as don't care; the device must be selected with S# LOW to start a hold (page 8). |
| 8 | VCC | power_in | Device core power supply; operating voltage is 2.3V to 3.6V for this part (page 8 and page 44). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Micron Tech |
| Package | SO-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input leakage current | ILI | -2 | | 2 | µA | | 36 |
| Output leakage current | ILO | -2 | | 2 | µA | | 36 |
| Standby current | ICC1 | | | 50 | µA | S# = VCC, VIN = VSS or VCC | 36 |
| Deep power-down current | ICC2 | | | 5 | µA | S# = VCC, VIN = VSS or VCC | 36 |
| Operating current (READ) | ICC3 | | | 8 | mA | C = 0.1VCC / 0.9VCC at 40 MHz and 75 MHz, DQ1 = open | 36 |
| Operating current (READ) | ICC3 | | | 4 | mA | C = 0.1VCC / 0.9VCC at 20 MHz, DQ1 = open | 36 |
| Operating current (PAGE PROGRAM) | ICC4 | | | 15 | mA | S# = VCC | 36 |
| Operating current (WRITE STATUS REGISTER) | ICC5 | | | 15 | mA | S# = VCC | 36 |
| Operating current (SECTOR ERASE) | ICC6 | | | 15 | mA | S# = VCC | 36 |
| Operating current (BULK ERASE) | ICC7 | | | 15 | mA | S# = VCC | 36 |
| Input LOW voltage | VIL | -0.5 | | | V | | 36 |
| Output LOW voltage | VOL | | | 0.4 | V | IOL = 1.6mA | 37 |
| WRITE STATUS REGISTER cycle time | tW | | 1.3 | 15 | ms | Device grade 6 | 37 |
| PAGE PROGRAM cycle time (256 bytes) | tPP | | 0.8 | 5 | ms | Device grade 6, 256 bytes | 37 |
| SECTOR ERASE cycle time | tSE | | 0.6 | 3 | s | Device grade 6 | 37 |
| BULK ERASE cycle time | tBE | | 2.5 | 6 | s | Device grade 6 | 37 |
| VCC(min) to S# LOW | tVSL | 10 | | | µs | Device grade 6 | 34 |
| Time delay to write instruction | tPUW | 1 | | 10 | ms | Device grade 6 | 34 |
| Write Inhibit voltage | VWI | 1 | | 2.1 | V | Device grade 6 | 34 |
| Supply voltage (operating) | VCC | 2.3 | | 3.6 | V | | 35 |
| Ambient operating temperature (grade 6) | TA | -40 | | 85 | °C | Grade 6 | 35 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 35 |
| Input and output voltage (with respect to ground) | VIO | -0.6 | | | V | | 35 |
| Supply voltage | VCC | -0.6 | | 4 | V | | 35 |
| Electrostatic discharge voltage (Human Body model) | VESD | -2000 | | 2000 | V | JEDEC JESD22-A114A | 35 |
| Program/Erase cycles | | 100000 | | | cycles | Cycles per sector, grade 6 | 35 |
| Data retention | | 20 | | | years | At 55°C | 35 |
| Output capacitance (DQ1) | COUT | | | 8 | pF | VOUT = 0 V | 38 |
| Input capacitance (other pins) | CIN | | | 6 | pF | VIN = 0 V | 38 |
| Load capacitance | CL | 30 | | 30 | pF | AC measurement conditions | 38 |
| Input rise and fall times | | | | 5 | ns | AC measurement conditions | 38 |
| Clock frequency for all commands (except READ) | fC | | | 75 | MHz | VCCmin = 2.7V | 39 |
| Clock frequency for READ command | fR | | | 33 | MHz | VCCmin = 2.7V | 39 |
| Clock HIGH time | tCH | 6 | | | ns | VCCmin = 2.7V | 39 |
| Clock LOW time | tCL | 6 | | | ns | VCCmin = 2.7V | 39 |
| Clock rise time (peak-to-peak) | tCLCH | 0.1 | | | V/ns | VCCmin = 2.7V | 39 |
| Clock fall time (peak-to-peak) | tCHCL | 0.1 | | | V/ns | VCCmin = 2.7V | 39 |
| S# active setup time (relative to C) | tSLCH | 5 | | | ns | VCCmin = 2.7V | 39 |
| S# not active hold time (relative to C) | tCHSL | 5 | | | ns | VCCmin = 2.7V | 39 |
| Data In setup time | tDVCH | 2 | | | ns | VCCmin = 2.7V | 39 |
| Data In hold time | tCHDX | 5 | | | ns | VCCmin = 2.7V | 39 |
| S# active hold time (relative to C) | tCHSH | 5 | | | ns | VCCmin = 2.7V | 39 |
| S# not active setup time (relative to C) | tSHCH | 5 | | | ns | VCCmin = 2.7V | 39 |
| S# deselect time | tSHSL | 100 | | | ns | VCCmin = 2.7V | 39 |
| Output disable time | tSHQZ | | | 8 | ns | VCCmin = 2.7V | 39 |
| Output hold time | tCLQX | 0 | | | ns | VCCmin = 2.7V | 39 |
| HOLD# setup time (relative to C) | tHLCH | 5 | | | ns | VCCmin = 2.7V | 39 |
| HOLD# hold time (relative to C) | tCHHH | 5 | | | ns | VCCmin = 2.7V | 39 |
| HOLD# to output Low-Z | tHHQX | | | 8 | ns | VCCmin = 2.7V | 39 |
| HOLD# to output High-Z | tHLQZ | | | 8 | ns | VCCmin = 2.7V | 39 |
| WRITE PROTECT setup time | tWHSL | 20 | | | ns | VCCmin = 2.7V | 39 |
| WRITE PROTECT hold time | tSHWL | 100 | | | ns | VCCmin = 2.7V | 39 |
| S# HIGH to deep power-down mode | tDP | | | 3 | µs | VCCmin = 2.7V | 39 |
| S# HIGH to STANDBY without READ ELECTRONIC SIGNATURE | tRES1 | | | 30 | µs | VCCmin = 2.7V | 39 |
| S# HIGH to STANDBY with READ ELECTRONIC SIGNATURE | tRES2 | | | 30 | µs | VCCmin = 2.7V | 39 |
## CAD (KiCad official)
- Symbol: `M25P20-VMN6TPB`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `m25p20-vmn6tpb-etched.step` / `m25p20-vmn6tpb-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m25p20-vmn6tpb.step` / `m25p20-vmn6tpb.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Micron Tech datasheet](docs/m25p20-vmn6tpb-datasheet.pdf) (46 pp, sha256 `1b298df2f2fdd036`, retrieved 2026-10-30, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m25p20-vmn6tpb-datasheet.pdf)