main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs m24c64-rmn6tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers pin 1: carry the footprint's marker into the .lbr, the viewer and page.json (silk-marker, drawn, top-left) · Ray
m24c64-rmn6tp-etched.fit.json m24c64-rmn6tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m24c64-rmn6tp-etched.glb m24c64-rmn6tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m24c64-rmn6tp-etched.step m24c64-rmn6tp: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
m24c64-rmn6tp.glb Publish 0.1.0 · Ray
m24c64-rmn6tp.kicad_mod Publish 0.1.0 · Ray
m24c64-rmn6tp.kicad_sym Publish 0.1.0 · Ray
m24c64-rmn6tp.lbr rebuild the library on adom-lbr 2.32.0. The published copy was built by 2.18.0, which imported every KiCad roundrect an… · Ray
m24c64-rmn6tp.step Publish 0.1.0 · Ray
package.json Publish 0.2.0 · Ray
pads.json pin 1: carry the footprint's marker into the .lbr, the viewer and page.json (silk-marker, drawn, top-left) · Ray
page.json m24c64-rmn6tp: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md m24c64-rmn6tp: laser-etched CAD + chip hero (factory 2.0.0 backfill) · Ray

M24C64-RMN6TP

STMicroelectronics · EEPROM · SOIC-8

M24C64-RMN6TP from STMicroelectronics, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip Enable address input bit 0. Sets bit b1 of the 7-bit I2C device select code, allowing up to 8 M24C64 devices to share a bus. Must be tied to VCC or VSS; if left floating, reads as 0.
2 E1 input Chip Enable address input bit 1. Sets bit b2 of the 7-bit I2C device select code. Must be tied to VCC or VSS; if left floating, reads as 0.
3 E2 input Chip Enable address input bit 2. Sets bit b3 of the 7-bit I2C device select code. Must be tied to VCC or VSS; if left floating, reads as 0.
4 VSS power_in Ground reference for VCC supply.
5 SDA bidirectional Serial Data input/output for the I2C bus. Open-drain output that must be pulled up to VCC through a resistor (value calculated per bus capacitance and speed). Used to transfer address, data-in, and data-out.
6 SCL input Serial Clock input for the I2C bus. Strobes data on SDA(in) and clocks out data on SDA(out). Supports 100 kHz, 400 kHz, and 1 MHz I2C bus modes.
7 WC input Write Control, active-low. When driven high, writes to the entire memory array are inhibited (address bytes are still acknowledged, data bytes are not). When driven low or left floating, write operations are enabled.
8 VCC power_in Supply voltage input. M24C64-R operating range: 1.8 V to 5.5 V over -40 C to +85 C. Decouple with a 10 nF to 100 nF capacitor between VCC and VSS close to the package.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SOIC-8
Category Memory
Pins 8

Ordering variants

Same part, different packaging or reel option.

  • M24C64-RMN6TP
  • M24C64-RMN6TPBN
  • M24C64-RMN6TPDW
  • M24C64-RMN6TPMC
  • M24C64-RMN6TPMH
  • M24C64-RMN6TPCU
  • M24C64-RMN6TPCS
  • M24C64-RMN6TPCT

CAD (KiCad official)

  • Symbol: M24C64-RMN6TP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: m24c64-rmn6tp-etched.step / m24c64-rmn6tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c64-rmn6tp.step / m24c64-rmn6tp.glb are the bare package body.

3D model downloads

Two STEP files. Same geometry, different body top:

File Size Use it when
m24c64-rmn6tp.step 122 KB You want the bare part, or you mark your own boards.
m24c64-rmn6tp-etched.step 2.3 MB You want the part with M24C64-RMN6TP already on it.

The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 584 faces against 147 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (53 pp, sha256 bc1cf4e678062294, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF