main
Ray Publish 0.1.0 131d483

M24C64-DRMN8TP

STMicroelectronics · EEPROM · SOP-8

M24C64-DRMN8TP from STMicroelectronics, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip Enable input setting bit b1 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
2 E1 input Chip Enable input setting bit b2 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
3 E2 input Chip Enable input setting bit b3 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial data input/output with an open-drain output that needs a pull-up resistor to VCC.
6 SCL input Serial clock input that strobes data in on SDA and clocks data out, supporting up to 1 MHz.
7 WC input Active-high Write Control input that disables writes to the entire memory array when driven high; writes are enabled when it is driven low or left floating.
8 VCC power_in Supply voltage pin, operating range 1.7 V to 5.5 V (absolute maximum 6.5 V), with a 10 nF to 100 nF decoupling capacitor recommended close to the pin.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient operating temperature -40 130 °C 26
Storage temperature TSTG -65 150 °C 26
Input or output range VIO -0.5 6.5 V 26
DC output current (SDA = 0) IOL 5 mA SDA = 0 26
Supply voltage VCC -0.5 6.5 V 26
Electrostatic pulse (Human Body model) VESD 4000 V Human Body model, AEC-Q100-002 26
Write cycle endurance Ncycle 4e+06 TA ≤ 25 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 900000 TA = 105 °C, 1.7 V < VCC < 5.5 V 27
Supply voltage (voltage range R) VCC 1.7 5.5 V voltage range R 27
Ambient operating temperature TA -40 105 °C 27
Input capacitance (SDA) CIN 8 pF 28
Input capacitance (other pins) CIN 6 pF 28
Input impedance (E2, E1, E0, WC) ZL 30 kΩ VIN < 0.3 VCC 28
Input impedance (E2, E1, E0, WC) ZH 500 kΩ VIN > 0.7 VCC 28
Input leakage current (SCL, SDA, E2, E1, E0) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 29
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 29
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 29
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 29
Supply current (Write) ICC0 2 mA During tW 29
Standby supply current ICC1 1 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 2 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V 29
Standby supply current ICC1 3 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Standby supply current ICC1 2.5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Input low voltage (SCL, SDA, WC) VIL -0.45 V 29
Input high voltage (SCL, SDA) VIH 6.5 V 29
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 29
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 29
Internal reset threshold voltage VRES 0.5 1.5 V 29
Clock frequency fC 400 kHz 400 kHz AC characteristics 30
Clock pulse width high tCHCL 600 ns 400 kHz AC characteristics 30
Clock pulse width low tCLCH 1300 ns 400 kHz AC characteristics 30
SDA (out) fall time tQL1QL2 20 120 ns 400 kHz AC characteristics, CL = 10 pF 30
Data in setup time tDXCH 100 ns 400 kHz AC characteristics 30
Data in hold time tCLDX 0 ns 400 kHz AC characteristics 30
Data out hold time tCLQX 100 ns 400 kHz AC characteristics 30
Clock low to next data valid (access time) tCLQV 900 ns 400 kHz AC characteristics 30
Start condition setup time tCHDL 600 ns 400 kHz AC characteristics 30
Start condition hold time tDLCL 600 ns 400 kHz AC characteristics 30
Stop condition set up time tCHDH 600 ns 400 kHz AC characteristics 30
Time between Stop condition and next Start condition tDHDL 1300 ns 400 kHz AC characteristics 30
Write time tW 4 ms 400 kHz AC characteristics 30
Clock frequency fC 0 1 MHz 1 MHz AC characteristics 31
Clock pulse width high tCHCL 260 ns 1 MHz AC characteristics 31
Clock pulse width low tCLCH 400 ns 1 MHz AC characteristics 31
SDA (out) fall time tQL1QL2 120 ns 1 MHz AC characteristics 31
Data in setup time tDXCH 50 ns 1 MHz AC characteristics 31
Data out hold time tCLQX 100 ns 1 MHz AC characteristics 31
Clock low to next data valid (access time) tCLQV 450 ns 1 MHz AC characteristics 31
Start condition setup time tCHDL 250 ns 1 MHz AC characteristics 31
Start condition hold time tDLCL 250 ns 1 MHz AC characteristics 31
Stop condition setup time tCHDH 250 ns 1 MHz AC characteristics 31
Time between Stop condition and next Start condition tDHDL 500 ns 1 MHz AC characteristics 31
Write time tW 4 ms 1 MHz AC characteristics 31

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST 26

CAD (KiCad official)

  • Symbol: M24C64-DRMN8TP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24c64-drmn8tp-k-etched.step / m24c64-drmn8tp-k-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c64-drmn8tp-k.step / m24c64-drmn8tp-k.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (42 pp, sha256 672dc8f58af2d187, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF