3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownM24C64-DRMN8TP
STMicroelectronics · EEPROM · SOP-8
M24C64-DRMN8TP from STMicroelectronics, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | E0 | input | Chip Enable input setting bit b1 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating. |
| 2 | E1 | input | Chip Enable input setting bit b2 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating. |
| 3 | E2 | input | Chip Enable input setting bit b3 of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that needs a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes data in on SDA and clocks data out, supporting up to 1 MHz. |
| 7 | WC | input | Active-high Write Control input that disables writes to the entire memory array when driven high; writes are enabled when it is driven low or left floating. |
| 8 | VCC | power_in | Supply voltage pin, operating range 1.7 V to 5.5 V (absolute maximum 6.5 V), with a 10 nF to 100 nF decoupling capacitor recommended close to the pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient operating temperature | -40 | 130 | °C | 26 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 26 | ||
| Input or output range | VIO | -0.5 | 6.5 | V | 26 | ||
| DC output current (SDA = 0) | IOL | 5 | mA | SDA = 0 | 26 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 26 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | Human Body model, AEC-Q100-002 | 26 | ||
| Write cycle endurance | Ncycle | 4e+06 | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 27 | |||
| Write cycle endurance | Ncycle | 1.2e+06 | TA = 85 °C, 1.7 V < VCC < 5.5 V | 27 | |||
| Write cycle endurance | Ncycle | 900000 | TA = 105 °C, 1.7 V < VCC < 5.5 V | 27 | |||
| Supply voltage (voltage range R) | VCC | 1.7 | 5.5 | V | voltage range R | 27 | |
| Ambient operating temperature | TA | -40 | 105 | °C | 27 | ||
| Input capacitance (SDA) | CIN | 8 | pF | 28 | |||
| Input capacitance (other pins) | CIN | 6 | pF | 28 | |||
| Input impedance (E2, E1, E0, WC) | ZL | 30 | kΩ | VIN < 0.3 VCC | 28 | ||
| Input impedance (E2, E1, E0, WC) | ZH | 500 | kΩ | VIN > 0.7 VCC | 28 | ||
| Input leakage current (SCL, SDA, E2, E1, E0) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 29 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 29 | |
| Supply current (Read) | ICC | 2 | mA | fC = 400 kHz, VCC = 5.5 V | 29 | ||
| Supply current (Read) | ICC | 1 | mA | fC = 400 kHz, VCC = 1.7 V | 29 | ||
| Supply current (Write) | ICC0 | 2 | mA | During tW | 29 | ||
| Standby supply current | ICC1 | 1 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V | 29 | ||
| Standby supply current | ICC1 | 2 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V | 29 | ||
| Standby supply current | ICC1 | 3 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V | 29 | ||
| Standby supply current | ICC1 | 2.5 | µA | Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V | 29 | ||
| Standby supply current | ICC1 | 5 | µA | Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V | 29 | ||
| Input low voltage (SCL, SDA, WC) | VIL | -0.45 | V | 29 | |||
| Input high voltage (SCL, SDA) | VIH | 6.5 | V | 29 | |||
| Output low voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V | 29 | ||
| Output low voltage | VOL | 0.3 | V | IOL = 1 mA, VCC = 1.7 V | 29 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 29 | ||
| Clock frequency | fC | 400 | kHz | 400 kHz AC characteristics | 30 | ||
| Clock pulse width high | tCHCL | 600 | ns | 400 kHz AC characteristics | 30 | ||
| Clock pulse width low | tCLCH | 1300 | ns | 400 kHz AC characteristics | 30 | ||
| SDA (out) fall time | tQL1QL2 | 20 | 120 | ns | 400 kHz AC characteristics, CL = 10 pF | 30 | |
| Data in setup time | tDXCH | 100 | ns | 400 kHz AC characteristics | 30 | ||
| Data in hold time | tCLDX | 0 | ns | 400 kHz AC characteristics | 30 | ||
| Data out hold time | tCLQX | 100 | ns | 400 kHz AC characteristics | 30 | ||
| Clock low to next data valid (access time) | tCLQV | 900 | ns | 400 kHz AC characteristics | 30 | ||
| Start condition setup time | tCHDL | 600 | ns | 400 kHz AC characteristics | 30 | ||
| Start condition hold time | tDLCL | 600 | ns | 400 kHz AC characteristics | 30 | ||
| Stop condition set up time | tCHDH | 600 | ns | 400 kHz AC characteristics | 30 | ||
| Time between Stop condition and next Start condition | tDHDL | 1300 | ns | 400 kHz AC characteristics | 30 | ||
| Write time | tW | 4 | ms | 400 kHz AC characteristics | 30 | ||
| Clock frequency | fC | 0 | 1 | MHz | 1 MHz AC characteristics | 31 | |
| Clock pulse width high | tCHCL | 260 | ns | 1 MHz AC characteristics | 31 | ||
| Clock pulse width low | tCLCH | 400 | ns | 1 MHz AC characteristics | 31 | ||
| SDA (out) fall time | tQL1QL2 | 120 | ns | 1 MHz AC characteristics | 31 | ||
| Data in setup time | tDXCH | 50 | ns | 1 MHz AC characteristics | 31 | ||
| Data out hold time | tCLQX | 100 | ns | 1 MHz AC characteristics | 31 | ||
| Clock low to next data valid (access time) | tCLQV | 450 | ns | 1 MHz AC characteristics | 31 | ||
| Start condition setup time | tCHDL | 250 | ns | 1 MHz AC characteristics | 31 | ||
| Start condition hold time | tDLCL | 250 | ns | 1 MHz AC characteristics | 31 | ||
| Stop condition setup time | tCHDH | 250 | ns | 1 MHz AC characteristics | 31 | ||
| Time between Stop condition and next Start condition | tDHDL | 500 | ns | 1 MHz AC characteristics | 31 | ||
| Write time | tW | 4 | ms | 1 MHz AC characteristics | 31 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST | 26 |
CAD (KiCad official)
- Symbol:
M24C64-DRMN8TP - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24c64-drmn8tp-k-etched.step/m24c64-drmn8tp-k-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24c64-drmn8tp-k.step/m24c64-drmn8tp-k.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (42 pp, sha256
672dc8f58af2d187, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).