main
Ray Publish 0.1.0 d9bb108

M24C08-DRDW3TP

The maker sells this part only as M24C08-DRDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 16, p.37)). The DigiKey and Mouser numbers on this page are for M24C08-DRDW3TP/K.

STMicroelectronics · EEPROM · TSSOP-8

M24C08-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect; the datasheet's 8-pin package connections figure shows this pin as NC with no function stated.
2 NC unconnected No connect; the datasheet's 8-pin package connections figure shows this pin as NC with no function stated.
3 E2 input Chip Enable input that sets the value looked for on bit b3 of the device select code, must be tied to VCC or VSS, and reads as low (0) when left floating.
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial data input/output with an open-drain output that can be wire-OR'ed on the bus and requires a pull-up resistor to VCC.
6 SCL input Serial clock input that strobes the data on SDA in and out.
7 WC input Write Control input that disables write operations to the entire memory array when driven high, and enables them when driven low or left floating.
8 VCC power_in Supply voltage pin, operating range 1.7 V to 5.5 V, with a 10 nF to 100 nF decoupling capacitor recommended close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient operating temperature (absolute maximum) -40 130 °C 24
Storage temperature TSTG -65 150 °C 24
Input or output range VIO -0.5 6.5 V 24
DC output current (SDA = 0) IOL 5 mA SDA = 0 24
Supply voltage (absolute maximum) VCC -0.5 6.5 V 24
Electrostatic pulse (Human Body model) VESD 4000 V Human Body model 24
Supply voltage (operating) VCC 1.7 5.5 V 25
Ambient operating temperature (operating) TA -40 125 °C 25
Input capacitance (SDA) CIN 8 pF 26
Input capacitance (other pins) CIN 6 pF 26
Input impedance (WC) ZL 30 kΩ VIN < 0.3 VCC 26
Input impedance (WC) ZH 500 kΩ VIN > 0.7 VCC 26
Write cycle endurance Ncycle 4e+06 TA ≤ 25 °C, 1.7 V < VCC < 5.5 V 26
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, 1.7 V < VCC < 5.5 V 26
Write cycle endurance Ncycle 600000 TA = 125 °C, 1.7 V < VCC < 5.5 V 26
Input leakage current (SCL, SDA, Ei) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 27
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 27
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 27
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 27
Supply current (Write) ICC0 2 mA During tW 27
Standby supply current ICC1 1 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V 27
Standby supply current ICC1 2 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V 27
Standby supply current ICC1 3 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V 27
Standby supply current ICC1 15 µA Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 1.7 V 27
Standby supply current ICC1 20 µA Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 5.5 V 27
Input low voltage (SCL, SDA, WC, Ei) VIL -0.45 V 27
Input low voltage (SCL, SDA, WC, Ei) VIL 0.3 VCC 27
Input high voltage (SCL, SDA) VIH 0.7 VCC 27
Input high voltage (SCL, SDA) VIH 6.5 V 27
Input high voltage (WC, Ei) VIH 0.7 VCC 27
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 27
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 27
Internal reset threshold voltage VRES 0.5 1.5 V 27
SCL clock frequency (400 kHz mode) fC 400 kHz 28
Clock pulse width high (400 kHz mode) tCHCL 600 ns 28
Clock pulse width low (400 kHz mode) tCLCH 1300 ns 28
SDA (out) fall time (400 kHz mode) tQL1QL2 20 120 ns CL = 10 pF 28
Data in setup time (400 kHz mode) tDXCH 100 ns 28
Data out hold time (400 kHz mode) tCLQX 100 ns 28
Clock low to next data valid (access time, 400 kHz mode) tCLQV 900 ns 28
Start condition setup time (400 kHz mode) tCHDL 600 ns 28
Time between Stop condition and next Start condition (400 kHz mode) tDHDL 1300 ns 28
Write time (400 kHz mode) tW 4 ms 28
Pulse width ignored (input filter on SCL and SDA), 400 kHz mode tNS 80 ns single glitch 28
SCL clock frequency (1 MHz mode) fC 0 1 MHz 29
Clock pulse width high (1 MHz mode) tCHCL 260 ns 29
Clock pulse width low (1 MHz mode) tCLCH 500 ns 29
SDA (out) fall time (1 MHz mode) tQL1QL2 20 120 ns 29
Data in setup time (1 MHz mode) tDXCH 50 ns 29
Data out hold time (1 MHz mode) tCLQX 100 ns 29
Clock low to next data valid (access time, 1 MHz mode) tCLQV 450 ns 29
Start condition setup time (1 MHz mode) tCHDL 250 ns 29
Time between Stop condition and next Start condition (1 MHz mode) tDHDL 500 ns 29
Write time (1 MHz mode) tW 4 ms 29
Pulse width ignored (input filter on SCL and SDA), 1 MHz mode tNS 80 ns 29

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® 24

CAD (KiCad official)

  • Symbol: M24C08-DRDW3TP
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24c08-drdw3tp-etched.step / m24c08-drdw3tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c08-drdw3tp.step / m24c08-drdw3tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (40 pp, sha256 03cd643d0d3bb938, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF