M24C08-DRDW3TP
The maker sells this part only as M24C08-DRDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 16, p.37)). The DigiKey and Mouser numbers on this page are for M24C08-DRDW3TP/K.
STMicroelectronics · EEPROM · TSSOP-8
M24C08-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect; the datasheet's 8-pin package connections figure shows this pin as NC with no function stated. |
| 2 | NC | unconnected | No connect; the datasheet's 8-pin package connections figure shows this pin as NC with no function stated. |
| 3 | E2 | input | Chip Enable input that sets the value looked for on bit b3 of the device select code, must be tied to VCC or VSS, and reads as low (0) when left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that can be wire-OR'ed on the bus and requires a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes the data on SDA in and out. |
| 7 | WC | input | Write Control input that disables write operations to the entire memory array when driven high, and enables them when driven low or left floating. |
| 8 | VCC | power_in | Supply voltage pin, operating range 1.7 V to 5.5 V, with a 10 nF to 100 nF decoupling capacitor recommended close to the VCC/VSS pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient operating temperature (absolute maximum) | -40 | 130 | °C | 24 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 24 | ||
| Input or output range | VIO | -0.5 | 6.5 | V | 24 | ||
| DC output current (SDA = 0) | IOL | 5 | mA | SDA = 0 | 24 | ||
| Supply voltage (absolute maximum) | VCC | -0.5 | 6.5 | V | 24 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | Human Body model | 24 | ||
| Supply voltage (operating) | VCC | 1.7 | 5.5 | V | 25 | ||
| Ambient operating temperature (operating) | TA | -40 | 125 | °C | 25 | ||
| Input capacitance (SDA) | CIN | 8 | pF | 26 | |||
| Input capacitance (other pins) | CIN | 6 | pF | 26 | |||
| Input impedance (WC) | ZL | 30 | kΩ | VIN < 0.3 VCC | 26 | ||
| Input impedance (WC) | ZH | 500 | kΩ | VIN > 0.7 VCC | 26 | ||
| Write cycle endurance | Ncycle | 4e+06 | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Write cycle endurance | Ncycle | 1.2e+06 | TA = 85 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Write cycle endurance | Ncycle | 600000 | TA = 125 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Input leakage current (SCL, SDA, Ei) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 27 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 27 | |
| Supply current (Read) | ICC | 2 | mA | fC = 400 kHz, VCC = 5.5 V | 27 | ||
| Supply current (Read) | ICC | 1 | mA | fC = 400 kHz, VCC = 1.7 V | 27 | ||
| Supply current (Write) | ICC0 | 2 | mA | During tW | 27 | ||
| Standby supply current | ICC1 | 1 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 | ||
| Standby supply current | ICC1 | 2 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V | 27 | ||
| Standby supply current | ICC1 | 3 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 | ||
| Standby supply current | ICC1 | 15 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 | ||
| Standby supply current | ICC1 | 20 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 | ||
| Input low voltage (SCL, SDA, WC, Ei) | VIL | -0.45 | V | 27 | |||
| Input low voltage (SCL, SDA, WC, Ei) | VIL | 0.3 | VCC | 27 | |||
| Input high voltage (SCL, SDA) | VIH | 0.7 | VCC | 27 | |||
| Input high voltage (SCL, SDA) | VIH | 6.5 | V | 27 | |||
| Input high voltage (WC, Ei) | VIH | 0.7 | VCC | 27 | |||
| Output low voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V | 27 | ||
| Output low voltage | VOL | 0.3 | V | IOL = 1 mA, VCC = 1.7 V | 27 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 27 | ||
| SCL clock frequency (400 kHz mode) | fC | 400 | kHz | 28 | |||
| Clock pulse width high (400 kHz mode) | tCHCL | 600 | ns | 28 | |||
| Clock pulse width low (400 kHz mode) | tCLCH | 1300 | ns | 28 | |||
| SDA (out) fall time (400 kHz mode) | tQL1QL2 | 20 | 120 | ns | CL = 10 pF | 28 | |
| Data in setup time (400 kHz mode) | tDXCH | 100 | ns | 28 | |||
| Data out hold time (400 kHz mode) | tCLQX | 100 | ns | 28 | |||
| Clock low to next data valid (access time, 400 kHz mode) | tCLQV | 900 | ns | 28 | |||
| Start condition setup time (400 kHz mode) | tCHDL | 600 | ns | 28 | |||
| Time between Stop condition and next Start condition (400 kHz mode) | tDHDL | 1300 | ns | 28 | |||
| Write time (400 kHz mode) | tW | 4 | ms | 28 | |||
| Pulse width ignored (input filter on SCL and SDA), 400 kHz mode | tNS | 80 | ns | single glitch | 28 | ||
| SCL clock frequency (1 MHz mode) | fC | 0 | 1 | MHz | 29 | ||
| Clock pulse width high (1 MHz mode) | tCHCL | 260 | ns | 29 | |||
| Clock pulse width low (1 MHz mode) | tCLCH | 500 | ns | 29 | |||
| SDA (out) fall time (1 MHz mode) | tQL1QL2 | 20 | 120 | ns | 29 | ||
| Data in setup time (1 MHz mode) | tDXCH | 50 | ns | 29 | |||
| Data out hold time (1 MHz mode) | tCLQX | 100 | ns | 29 | |||
| Clock low to next data valid (access time, 1 MHz mode) | tCLQV | 450 | ns | 29 | |||
| Start condition setup time (1 MHz mode) | tCHDL | 250 | ns | 29 | |||
| Time between Stop condition and next Start condition (1 MHz mode) | tDHDL | 500 | ns | 29 | |||
| Write time (1 MHz mode) | tW | 4 | ms | 29 | |||
| Pulse width ignored (input filter on SCL and SDA), 1 MHz mode | tNS | 80 | ns | 29 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 24 |
CAD (KiCad official)
- Symbol:
M24C08-DRDW3TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24c08-drdw3tp-etched.step/m24c08-drdw3tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24c08-drdw3tp.step/m24c08-drdw3tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (40 pp, sha256
03cd643d0d3bb938, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).