main
Ray
Publish 0.1.0
be7367f
M0G3507QRGZRQ1
Texas Instruments · IC · VQFN-48(7x7)
M0G3507QRGZRQ1 from Texas Instruments, in a VQFN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0 | bidirectional | General-purpose 5 V-tolerant open-drain I/O with wake from SHUTDOWN, default BSL I2C_SDA, and FCC_IN, UART0_TX, I2C0_SDA and TIMA0_C0 as alternates; an external pull-up is required for output high. |
| 2 | PA1 | bidirectional | General-purpose 5 V-tolerant open-drain I/O with default BSL I2C_SCL, and UART0_RX, I2C0_SCL and TIMA0_C1 as alternates; an external pull-up is required for output high. |
| 3 | PA28 | bidirectional | High-drive GPIO with wake from SHUTDOWN, with UART0_TX, I2C0_SDA and TIMA0_C3 as alternate functions; the high-drive IO is rated for 20 mA sink or source. |
| 4 | NRST | input | Active-low reset input that must be pulled high to VDD for the device to release from reset and start the boot process. |
| 5 | PA31 | bidirectional | High-drive GPIO with wake from SHUTDOWN, with UART0_RX, I2C0_SCL, TIMA0_C3N and CLK_OUT as alternate functions; the high-drive IO is rated for 20 mA. |
| 6 | VDD | power_in | Power supply, 1.62 V to 3.6 V per recommended operating conditions, with a 10 µF capacitor from VDD to VSS required. |
| 7 | VSS | power_in | Ground supply for the device; TI recommends connecting the QFN exposed thermal pad to VSS. |
| 8 | PA2 | bidirectional | General-purpose I/O that is also the ROSC pin; when the SYSOSC frequency correction loop is used, a 100 kΩ ±0.1% resistor to VSS is required on this pin. |
| 9 | PA3 | bidirectional | General-purpose I/O that also serves as the LFXIN input for the 32 kHz low-frequency crystal oscillator (LFXT). |
| 10 | PA4 | bidirectional | General-purpose I/O that also serves as the LFXOUT crystal output or LFCLK_IN digital low-frequency clock input. |
| 11 | PA5 | bidirectional | General-purpose I/O that also serves as the HFXIN input for the high-frequency crystal oscillator (HFXT) or FCC_IN. |
| 12 | PA6 | bidirectional | General-purpose I/O that also serves as the HFXOUT crystal output for HFXT or the HFCLK_IN digital high-frequency clock input. |
| 13 | PA7 | bidirectional | Standard general-purpose I/O with CLK_OUT (configurable clock output), COMP0_OUT, and TIMA0_C2 as alternate functions. |
| 14 | PB2 | bidirectional | Standard general-purpose I/O with UART3_TX, I2C1_SCL and TIMA0_C3 as alternate functions. |
| 15 | PB3 | bidirectional | Standard general-purpose I/O with UART3_RX, I2C1_SDA and TIMA0_C3N as alternate functions. |
| 16 | PA8 | bidirectional | Standard general-purpose I/O with UART1_TX, SPI0_CS0 and TIMA0_C0 as alternate functions. |
| 17 | PA9 | bidirectional | High-speed general-purpose I/O with UART1_RX, SPI0_PICO, RTC_OUT and CLK_OUT as alternate functions. |
| 18 | PA10 | bidirectional | High-drive general-purpose I/O (rated 20 mA) with default BSL UART_TX, UART0_TX, I2C0_SDA and CLK_OUT as alternate functions. |
| 19 | PA11 | bidirectional | High-drive general-purpose I/O (rated 20 mA) with default BSL UART_RX, UART0_RX, I2C0_SCL and COMP0_OUT as alternate functions. |
| 20 | PB6 | bidirectional | Standard general-purpose I/O with UART1_TX, SPI1_CS0 and TIMG8_C0 as alternate functions. |
| 21 | PB7 | bidirectional | Standard general-purpose I/O with UART1_RX, SPI1_POCI and TIMG8_C1 as alternate functions. |
| 22 | PB8 | bidirectional | Standard general-purpose I/O with UART1_CTS, SPI1_PICO, TIMA0_C0 and COMP1_OUT as alternate functions. |
| 23 | PB9 | bidirectional | Standard general-purpose I/O with UART1_RTS, SPI1_SCK and TIMA0_C1 as alternate functions. |
| 24 | PB14 | bidirectional | Standard general-purpose I/O with SPI1_CS3, SPI1_POCI and TIMA0_C0 as alternate functions. |
| 25 | PB15 | bidirectional | Standard general-purpose I/O with UART2_TX, SPI1_PICO and UART3_CTS as alternate functions. |
| 26 | PB16 | bidirectional | Standard general-purpose I/O with UART2_RX, SPI1_SCK and UART3_RTS as alternate functions. |
| 27 | PA12 | bidirectional | High-speed general-purpose I/O with UART3_CTS, SPI0_SCK, CAN_TX and FCC_IN as alternate functions. |
| 28 | PA13 | bidirectional | High-speed general-purpose I/O with COMP0_IN2- analog input, UART3_RTS, SPI0_POCI and CAN_RX as alternate functions. |
| 29 | PA14 | bidirectional | High-speed general-purpose I/O that is also the COMP0_IN2+ analog input and ADC0 analog input A0_12. |
| 30 | PA15 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_0 and DAC_OUT; when DAC_OUT is used, A1_0 cannot sample external signals and external circuitry should be avoided on this pin. |
| 31 | PA16 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_1 and OPA1_OUT, with COMP2_OUT and FCC_IN as alternates. |
| 32 | PA17 | bidirectional | Standard general-purpose I/O with wake from SHUTDOWN that is also ADC1 analog input A1_2, OPA1_IN1- and COMP0_IN1-. |
| 33 | PA18 | bidirectional | Standard general-purpose I/O with wake from SHUTDOWN that is also ADC1 analog input A1_3, OPA1_IN1+, COMP0_IN1+ and GPAMP_IN-, and serves as the default BSL_invoke input. |
| 34 | PA19 | bidirectional | High-speed general-purpose I/O that serves as the SWDIO serial wire debug data input/output. |
| 35 | PA20 | bidirectional | Standard general-purpose I/O that serves as the SWCLK serial wire debug clock input. |
| 36 | PB17 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_4 and COMP1_IN2-, with UART2_TX and SPI0_PICO as alternates. |
| 37 | PB18 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_5 and COMP1_IN2+, with UART2_RX and SPI0_SCK as alternates. |
| 38 | PB19 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_6, COMP2_IN1+ and OPA1_IN0+, with COMP2_OUT as an alternate. |
| 39 | PA21 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_7, COMP2_IN1- and the VREF- reference ground; this pin has an internal test connection and no injection current is allowed on it. |
| 40 | PA22 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_7, GPAMP_OUT and OPA0_OUT, with CLK_OUT as an alternate. |
| 41 | PB20 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_6 and OPA1_IN0-, with SPI0_CS2 and TIMA0_C2 as alternates. |
| 42 | PB24 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_5 and COMP1_IN1+, with SPI0_CS3 and TIMA0_C3 as alternates. |
| 43 | PA23 | bidirectional | Standard general-purpose I/O that serves as the VREF+ voltage reference input (external reference) or internal reference output, and is also COMP1_IN1-. |
| 44 | PA24 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_3 and OPA0_IN1-, with UART2_RX and SPI0_CS2 as alternates. |
| 45 | PA25 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_2 and OPA0_IN1+, with UART3_RX and SPI1_CS3 as alternates. |
| 46 | PA26 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_1, COMP0_IN0+, OPA0_IN0+ and GPAMP_IN+, with UART3_TX and SPI1_CS0 as alternates. |
| 47 | PA27 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_0, COMP0_IN0- and OPA0_IN0-, with RTC_OUT and SPI1_CS1 as alternates. |
| 48 | VCORE | power_out | Regulated core power supply output that requires a 470 nF capacitor to VSS placed close to the device; do not supply any voltage or apply any external load to this pin. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48(7x7) |
| Category | |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage at VDD pin | VDD | -0.3 | 4.1 | V | At VDD pin | 27 | |
| Input voltage, 5-V tolerant open-drain pins | VI | -0.3 | 5.5 | V | Applied to any 5-V tolerant open-drain pins | 27 | |
| Input voltage, common tolerance pins | VI | -0.3 | 4.1 | V | Applied to any common tolerance pins; printed as VDD + 0.3 (4.1 MAX) | 27 | |
| Current into VDD pin (source) | IVDD | 80 | mA | -40℃ ≤ Tj ≤ 130℃ | 27 | ||
| Current into VDD pin (source) | IVDD | 100 | mA | -40℃ ≤ Tj ≤ 90℃ | 27 | ||
| Current out of VSS pin (sink) | IVSS | 80 | mA | -40℃ ≤ Tj≤ 130℃ | 27 | ||
| Current out of VSS pin (sink) | IVSS | 100 | mA | -40℃ ≤ Tj≤ 90℃ | 27 | ||
| Current of SDIO pin | IIO | 6 | mA | Current sunk or sourced by SDIO pin | 27 | ||
| Current of HSIO pin | IIO | 6 | mA | Current sunk or sourced by HSIO pin | 27 | ||
| Current of HDIO pin | IIO | 20 | mA | Current sunk or sourced by HDIO pin | 27 | ||
| Current of ODIO pin | IIO | 20 | mA | Current sunk by ODIO pin | 27 | ||
| Supported diode current | ID | -2 | 2 | mA | Diode current at any device pin | 27 | |
| Ambient temperature | TA | -40 | 125 | °C | 27 | ||
| Junction temperature | TJ | -40 | 130 | °C | 27 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 27 | ||
| Supply voltage | VDD | 1.62 | 3.6 | V | 27 | ||
| Ambient temperature, Q version | TA | -40 | 125 | °C | Q version | 27 | |
| Max junction temperature, Q version | TJ | 130 | °C | Q version | 27 | ||
| MCLK, CPUCLK frequency with 2 flash wait states | fMCLK | 80 | MHz | MCLK, CPUCLK frequency with 2 flash wait states | 28 | ||
| MCLK, CPUCLK frequency with 1 flash wait state | fMCLK | 48 | MHz | MCLK, CPUCLK frequency with 1 flash wait state | 28 | ||
| MCLK, CPUCLK frequency with 0 flash wait states | fMCLK | 24 | MHz | MCLK, CPUCLK frequency with 0 flash wait states | 28 | ||
| ULPCLK frequency (PD0 bus clock) | fULPCLK | 40 | MHz | 28 | |||
| High level input voltage, ODIO | VIH | 5.5 | V | VDD≥1.62V; printed min is 0.7*VDD | 37 | ||
| High level input voltage, ODIO | VIH | 2 | 5.5 | V | VDD≥2.7V | 37 | |
| Low level input voltage, ODIO | VIL | -0.3 | V | VDD≥1.62V; printed max is 0.3*VDD | 37 | ||
| Low level input voltage, ODIO | VIL | -0.3 | 0.8 | V | VDD≥2.7V | 37 | |
| Low level input voltage, all I/O except ODIO & Reset | VIL | -0.3 | V | VDD≥1.62V; printed max is 0.3*VDD | 37 | ||
| High-Z leakage current (All packages except PM) SDIO | Ilkg | 50 | nA | 1.62V ≤ VDD ≤ 3.6V, -40 ℃ ≤ Ta ≤ 125 ℃ | 37 | ||
| Low level output voltage, SDIO | VOL | 0.4 | V | VDD≥2.7V, /IIO/,max=6mA; VDD≥1.71V, /IIO/,max=2mA; VDD≥1.62V, /IIO/,max=1.5mA; -40 °C ≤Ta≤25 °C | 39 | ||
| Low level output voltage, SDIO | VOL | 0.45 | V | VDD≥2.7V, /IIO/,max=6mA; VDD≥1.71V, /IIO/,max=2mA; VDD≥1.62V, /IIO/,max=1.5mA; -40 °C ≤Ta≤125 °C | 39 | ||
| Low level output voltage, ODIO | VOL | 0.4 | V | VDD≥2.7V, IOL,max=8mA; VDD≥1.71V, IOL,max=4mA; -40 °C ≤Ta≤25 °C | 39 | ||
| Low level output voltage, ODIO | VOL | 0.45 | V | VDD≥2.7V, IOL,max=8mA; VDD≥1.71V, IOL,max=4mA; -40 °C ≤Ta≤125 °C | 39 | ||
| Output fall time, ODIO | tf | 120 | ns | VDD ≥ 1.71V, FM+, CL= 20pF-100pF; printed min is 20*VDD/5.5 | 40 | ||
| STOP mode supply current, IDDSTOP0 | IDDSTOP0 | 450 | uA | VDD=3.3V; 25°C; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; ULPCLK 4MHz | 30 | ||
| STOP mode supply current, IDDSTOP0 | IDDSTOP0 | 577 | uA | VDD=3.3V; 125°C; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; ULPCLK 4MHz | 30 | ||
| STOP mode supply current, IDDSTOP2 | IDDSTOP2 | 67 | uA | VDD=3.3V; 25°C; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz | 30 | ||
| STOP mode supply current, IDDSTOP2 | IDDSTOP2 | 170 | uA | VDD=3.3V; 125°C; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz | 30 | ||
| SLEEP mode supply current, IDDSLEEP | IDDSLEEP | 3400 | uA | VDD=3.3V; 25°C; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted, 80MHz | 30 | ||
| SLEEP mode supply current, IDDSLEEP | IDDSLEEP | 5509 | uA | VDD=3.3V; 125°C; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted, 80MHz | 30 | ||
| STANDBY mode supply current, IDDSTBY0 | IDDSTBY0 | 7 | uA | VDD=3.3V; 25°C; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, 32kHz | 31 | ||
| STANDBY mode supply current, IDDSTBY0 | IDDSTBY0 | 105 | uA | VDD=3.3V; 125°C; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, 32kHz | 31 | ||
| VREF output voltage | VREF | 1.38 | 1.4 | 1.42 | V | BUFCONFIG = 1 | 43 |
| VREF output voltage | VREF | 2.46 | 2.5 | 2.54 | V | BUFCONFIG = 0 | 43 |
| Power-on reset voltage level, rising | VPOR+ | 0.95 | 1.3 | 1.59 | V | Rising | 31 |
| Power-on reset voltage level, falling | VPOR- | 0.9 | 1.25 | 1.54 | V | Falling | 31 |
| Brown-out reset voltage level 0, rising | VBOR0+ | 1.56 | 1.59 | 1.62 | V | Rising; device operating in RUN, SLEEP, or STOP mode | 32 |
| Integral linearity error (INL) | EI | -2 | 2 | LSB | External reference | 42 | |
| Differential linearity error (DNL) | ED | -1 | 1 | LSB | Guaranteed no missing codes; External reference | 42 | |
| Offset error | EO | -5 | 5 | mV | Internal or External reference | 42 | |
| Gain error | EG | -4 | 4 | LSB | External reference | 42 | |
| Temperature coefficient | TSc | -2.1 | -1.8 | -1.7 | mV/℃ | -40℃ ≤ Tj ≤ 130℃ | 43 |
| Core voltage on VCORE pin | VCORE | 1.35 | V | 27 | |||
| Capacitor connected between VDD and VSS | CVDD | 10 | uF | 27 | |||
| Capacitor connected between VCORE and VSS | CVCORE | 470 | nF | 27 | |||
| Junction-to-ambient thermal resistance (VQFN-48 RGZ) | RθJA | 29.9 | °C/W | 28 | |||
| Junction-to-case (top) thermal resistance (VQFN-48 RGZ) | RθJC(top) | 20.5 | °C/W | 28 | |||
| Junction-to-board thermal resistance (VQFN-48 RGZ) | RθJB | 12.3 | °C/W | 28 | |||
| Junction-to-top characterization parameter (VQFN-48 RGZ) | ΨJT | 0.4 | °C/W | 28 | |||
| Junction-to-board characterization parameter (VQFN-48 RGZ) | ΨJB | 12.2 | °C/W | 28 | |||
| Junction-to-case (bottom) thermal resistance (VQFN-48 RGZ) | RθJC(bot) | 4.1 | °C/W | 28 |
CAD (KiCad official)
- Symbol:
M0G3507QRGZRQ1 - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
m0g3507qrgzrq1-etched.step/m0g3507qrgzrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m0g3507qrgzrq1.step/m0g3507qrgzrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (126 pp, sha256
c44df29a9981ebcd, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M0G3507QRGZRQ1
**Texas Instruments** · IC · VQFN-48(7x7)
M0G3507QRGZRQ1 from Texas Instruments, in a VQFN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0 | bidirectional | General-purpose 5 V-tolerant open-drain I/O with wake from SHUTDOWN, default BSL I2C_SDA, and FCC_IN, UART0_TX, I2C0_SDA and TIMA0_C0 as alternates; an external pull-up is required for output high. |
| 2 | PA1 | bidirectional | General-purpose 5 V-tolerant open-drain I/O with default BSL I2C_SCL, and UART0_RX, I2C0_SCL and TIMA0_C1 as alternates; an external pull-up is required for output high. |
| 3 | PA28 | bidirectional | High-drive GPIO with wake from SHUTDOWN, with UART0_TX, I2C0_SDA and TIMA0_C3 as alternate functions; the high-drive IO is rated for 20 mA sink or source. |
| 4 | NRST | input | Active-low reset input that must be pulled high to VDD for the device to release from reset and start the boot process. |
| 5 | PA31 | bidirectional | High-drive GPIO with wake from SHUTDOWN, with UART0_RX, I2C0_SCL, TIMA0_C3N and CLK_OUT as alternate functions; the high-drive IO is rated for 20 mA. |
| 6 | VDD | power_in | Power supply, 1.62 V to 3.6 V per recommended operating conditions, with a 10 µF capacitor from VDD to VSS required. |
| 7 | VSS | power_in | Ground supply for the device; TI recommends connecting the QFN exposed thermal pad to VSS. |
| 8 | PA2 | bidirectional | General-purpose I/O that is also the ROSC pin; when the SYSOSC frequency correction loop is used, a 100 kΩ ±0.1% resistor to VSS is required on this pin. |
| 9 | PA3 | bidirectional | General-purpose I/O that also serves as the LFXIN input for the 32 kHz low-frequency crystal oscillator (LFXT). |
| 10 | PA4 | bidirectional | General-purpose I/O that also serves as the LFXOUT crystal output or LFCLK_IN digital low-frequency clock input. |
| 11 | PA5 | bidirectional | General-purpose I/O that also serves as the HFXIN input for the high-frequency crystal oscillator (HFXT) or FCC_IN. |
| 12 | PA6 | bidirectional | General-purpose I/O that also serves as the HFXOUT crystal output for HFXT or the HFCLK_IN digital high-frequency clock input. |
| 13 | PA7 | bidirectional | Standard general-purpose I/O with CLK_OUT (configurable clock output), COMP0_OUT, and TIMA0_C2 as alternate functions. |
| 14 | PB2 | bidirectional | Standard general-purpose I/O with UART3_TX, I2C1_SCL and TIMA0_C3 as alternate functions. |
| 15 | PB3 | bidirectional | Standard general-purpose I/O with UART3_RX, I2C1_SDA and TIMA0_C3N as alternate functions. |
| 16 | PA8 | bidirectional | Standard general-purpose I/O with UART1_TX, SPI0_CS0 and TIMA0_C0 as alternate functions. |
| 17 | PA9 | bidirectional | High-speed general-purpose I/O with UART1_RX, SPI0_PICO, RTC_OUT and CLK_OUT as alternate functions. |
| 18 | PA10 | bidirectional | High-drive general-purpose I/O (rated 20 mA) with default BSL UART_TX, UART0_TX, I2C0_SDA and CLK_OUT as alternate functions. |
| 19 | PA11 | bidirectional | High-drive general-purpose I/O (rated 20 mA) with default BSL UART_RX, UART0_RX, I2C0_SCL and COMP0_OUT as alternate functions. |
| 20 | PB6 | bidirectional | Standard general-purpose I/O with UART1_TX, SPI1_CS0 and TIMG8_C0 as alternate functions. |
| 21 | PB7 | bidirectional | Standard general-purpose I/O with UART1_RX, SPI1_POCI and TIMG8_C1 as alternate functions. |
| 22 | PB8 | bidirectional | Standard general-purpose I/O with UART1_CTS, SPI1_PICO, TIMA0_C0 and COMP1_OUT as alternate functions. |
| 23 | PB9 | bidirectional | Standard general-purpose I/O with UART1_RTS, SPI1_SCK and TIMA0_C1 as alternate functions. |
| 24 | PB14 | bidirectional | Standard general-purpose I/O with SPI1_CS3, SPI1_POCI and TIMA0_C0 as alternate functions. |
| 25 | PB15 | bidirectional | Standard general-purpose I/O with UART2_TX, SPI1_PICO and UART3_CTS as alternate functions. |
| 26 | PB16 | bidirectional | Standard general-purpose I/O with UART2_RX, SPI1_SCK and UART3_RTS as alternate functions. |
| 27 | PA12 | bidirectional | High-speed general-purpose I/O with UART3_CTS, SPI0_SCK, CAN_TX and FCC_IN as alternate functions. |
| 28 | PA13 | bidirectional | High-speed general-purpose I/O with COMP0_IN2- analog input, UART3_RTS, SPI0_POCI and CAN_RX as alternate functions. |
| 29 | PA14 | bidirectional | High-speed general-purpose I/O that is also the COMP0_IN2+ analog input and ADC0 analog input A0_12. |
| 30 | PA15 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_0 and DAC_OUT; when DAC_OUT is used, A1_0 cannot sample external signals and external circuitry should be avoided on this pin. |
| 31 | PA16 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_1 and OPA1_OUT, with COMP2_OUT and FCC_IN as alternates. |
| 32 | PA17 | bidirectional | Standard general-purpose I/O with wake from SHUTDOWN that is also ADC1 analog input A1_2, OPA1_IN1- and COMP0_IN1-. |
| 33 | PA18 | bidirectional | Standard general-purpose I/O with wake from SHUTDOWN that is also ADC1 analog input A1_3, OPA1_IN1+, COMP0_IN1+ and GPAMP_IN-, and serves as the default BSL_invoke input. |
| 34 | PA19 | bidirectional | High-speed general-purpose I/O that serves as the SWDIO serial wire debug data input/output. |
| 35 | PA20 | bidirectional | Standard general-purpose I/O that serves as the SWCLK serial wire debug clock input. |
| 36 | PB17 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_4 and COMP1_IN2-, with UART2_TX and SPI0_PICO as alternates. |
| 37 | PB18 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_5 and COMP1_IN2+, with UART2_RX and SPI0_SCK as alternates. |
| 38 | PB19 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_6, COMP2_IN1+ and OPA1_IN0+, with COMP2_OUT as an alternate. |
| 39 | PA21 | bidirectional | Standard general-purpose I/O that is also ADC1 analog input A1_7, COMP2_IN1- and the VREF- reference ground; this pin has an internal test connection and no injection current is allowed on it. |
| 40 | PA22 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_7, GPAMP_OUT and OPA0_OUT, with CLK_OUT as an alternate. |
| 41 | PB20 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_6 and OPA1_IN0-, with SPI0_CS2 and TIMA0_C2 as alternates. |
| 42 | PB24 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_5 and COMP1_IN1+, with SPI0_CS3 and TIMA0_C3 as alternates. |
| 43 | PA23 | bidirectional | Standard general-purpose I/O that serves as the VREF+ voltage reference input (external reference) or internal reference output, and is also COMP1_IN1-. |
| 44 | PA24 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_3 and OPA0_IN1-, with UART2_RX and SPI0_CS2 as alternates. |
| 45 | PA25 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_2 and OPA0_IN1+, with UART3_RX and SPI1_CS3 as alternates. |
| 46 | PA26 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_1, COMP0_IN0+, OPA0_IN0+ and GPAMP_IN+, with UART3_TX and SPI1_CS0 as alternates. |
| 47 | PA27 | bidirectional | Standard general-purpose I/O that is also ADC0 analog input A0_0, COMP0_IN0- and OPA0_IN0-, with RTC_OUT and SPI1_CS1 as alternates. |
| 48 | VCORE | power_out | Regulated core power supply output that requires a 470 nF capacitor to VSS placed close to the device; do not supply any voltage or apply any external load to this pin. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48(7x7) |
| Category | |
| Pins | 49 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage at VDD pin | VDD | -0.3 | | 4.1 | V | At VDD pin | 27 |
| Input voltage, 5-V tolerant open-drain pins | VI | -0.3 | | 5.5 | V | Applied to any 5-V tolerant open-drain pins | 27 |
| Input voltage, common tolerance pins | VI | -0.3 | | 4.1 | V | Applied to any common tolerance pins; printed as VDD + 0.3 (4.1 MAX) | 27 |
| Current into VDD pin (source) | IVDD | | | 80 | mA | -40℃ ≤ Tj ≤ 130℃ | 27 |
| Current into VDD pin (source) | IVDD | | | 100 | mA | -40℃ ≤ Tj ≤ 90℃ | 27 |
| Current out of VSS pin (sink) | IVSS | | | 80 | mA | -40℃ ≤ Tj≤ 130℃ | 27 |
| Current out of VSS pin (sink) | IVSS | | | 100 | mA | -40℃ ≤ Tj≤ 90℃ | 27 |
| Current of SDIO pin | IIO | | | 6 | mA | Current sunk or sourced by SDIO pin | 27 |
| Current of HSIO pin | IIO | | | 6 | mA | Current sunk or sourced by HSIO pin | 27 |
| Current of HDIO pin | IIO | | | 20 | mA | Current sunk or sourced by HDIO pin | 27 |
| Current of ODIO pin | IIO | | | 20 | mA | Current sunk by ODIO pin | 27 |
| Supported diode current | ID | -2 | | 2 | mA | Diode current at any device pin | 27 |
| Ambient temperature | TA | -40 | | 125 | °C | | 27 |
| Junction temperature | TJ | -40 | | 130 | °C | | 27 |
| Storage temperature | Tstg | -40 | | 150 | °C | | 27 |
| Supply voltage | VDD | 1.62 | | 3.6 | V | | 27 |
| Ambient temperature, Q version | TA | -40 | | 125 | °C | Q version | 27 |
| Max junction temperature, Q version | TJ | | | 130 | °C | Q version | 27 |
| MCLK, CPUCLK frequency with 2 flash wait states | fMCLK | | | 80 | MHz | MCLK, CPUCLK frequency with 2 flash wait states | 28 |
| MCLK, CPUCLK frequency with 1 flash wait state | fMCLK | | | 48 | MHz | MCLK, CPUCLK frequency with 1 flash wait state | 28 |
| MCLK, CPUCLK frequency with 0 flash wait states | fMCLK | | | 24 | MHz | MCLK, CPUCLK frequency with 0 flash wait states | 28 |
| ULPCLK frequency (PD0 bus clock) | fULPCLK | | | 40 | MHz | | 28 |
| High level input voltage, ODIO | VIH | | | 5.5 | V | VDD≥1.62V; printed min is 0.7*VDD | 37 |
| High level input voltage, ODIO | VIH | 2 | | 5.5 | V | VDD≥2.7V | 37 |
| Low level input voltage, ODIO | VIL | -0.3 | | | V | VDD≥1.62V; printed max is 0.3*VDD | 37 |
| Low level input voltage, ODIO | VIL | -0.3 | | 0.8 | V | VDD≥2.7V | 37 |
| Low level input voltage, all I/O except ODIO & Reset | VIL | -0.3 | | | V | VDD≥1.62V; printed max is 0.3*VDD | 37 |
| High-Z leakage current (All packages except PM) SDIO | Ilkg | | | 50 | nA | 1.62V ≤ VDD ≤ 3.6V, -40 ℃ ≤ Ta ≤ 125 ℃ | 37 |
| Low level output voltage, SDIO | VOL | | | 0.4 | V | VDD≥2.7V, /IIO/,max=6mA; VDD≥1.71V, /IIO/,max=2mA; VDD≥1.62V, /IIO/,max=1.5mA; -40 °C ≤Ta≤25 °C | 39 |
| Low level output voltage, SDIO | VOL | | | 0.45 | V | VDD≥2.7V, /IIO/,max=6mA; VDD≥1.71V, /IIO/,max=2mA; VDD≥1.62V, /IIO/,max=1.5mA; -40 °C ≤Ta≤125 °C | 39 |
| Low level output voltage, ODIO | VOL | | | 0.4 | V | VDD≥2.7V, IOL,max=8mA; VDD≥1.71V, IOL,max=4mA; -40 °C ≤Ta≤25 °C | 39 |
| Low level output voltage, ODIO | VOL | | | 0.45 | V | VDD≥2.7V, IOL,max=8mA; VDD≥1.71V, IOL,max=4mA; -40 °C ≤Ta≤125 °C | 39 |
| Output fall time, ODIO | tf | | | 120 | ns | VDD ≥ 1.71V, FM+, CL= 20pF-100pF; printed min is 20*VDD/5.5 | 40 |
| STOP mode supply current, IDDSTOP0 | IDDSTOP0 | | | 450 | uA | VDD=3.3V; 25°C; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; ULPCLK 4MHz | 30 |
| STOP mode supply current, IDDSTOP0 | IDDSTOP0 | | | 577 | uA | VDD=3.3V; 125°C; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; ULPCLK 4MHz | 30 |
| STOP mode supply current, IDDSTOP2 | IDDSTOP2 | | | 67 | uA | VDD=3.3V; 25°C; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz | 30 |
| STOP mode supply current, IDDSTOP2 | IDDSTOP2 | | | 170 | uA | VDD=3.3V; 125°C; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz | 30 |
| SLEEP mode supply current, IDDSLEEP | IDDSLEEP | | | 3400 | uA | VDD=3.3V; 25°C; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted, 80MHz | 30 |
| SLEEP mode supply current, IDDSLEEP | IDDSLEEP | | | 5509 | uA | VDD=3.3V; 125°C; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted, 80MHz | 30 |
| STANDBY mode supply current, IDDSTBY0 | IDDSTBY0 | | | 7 | uA | VDD=3.3V; 25°C; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, 32kHz | 31 |
| STANDBY mode supply current, IDDSTBY0 | IDDSTBY0 | | | 105 | uA | VDD=3.3V; 125°C; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, 32kHz | 31 |
| VREF output voltage | VREF | 1.38 | 1.4 | 1.42 | V | BUFCONFIG = 1 | 43 |
| VREF output voltage | VREF | 2.46 | 2.5 | 2.54 | V | BUFCONFIG = 0 | 43 |
| Power-on reset voltage level, rising | VPOR+ | 0.95 | 1.3 | 1.59 | V | Rising | 31 |
| Power-on reset voltage level, falling | VPOR- | 0.9 | 1.25 | 1.54 | V | Falling | 31 |
| Brown-out reset voltage level 0, rising | VBOR0+ | 1.56 | 1.59 | 1.62 | V | Rising; device operating in RUN, SLEEP, or STOP mode | 32 |
| Integral linearity error (INL) | EI | -2 | | 2 | LSB | External reference | 42 |
| Differential linearity error (DNL) | ED | -1 | | 1 | LSB | Guaranteed no missing codes; External reference | 42 |
| Offset error | EO | -5 | | 5 | mV | Internal or External reference | 42 |
| Gain error | EG | -4 | | 4 | LSB | External reference | 42 |
| Temperature coefficient | TSc | -2.1 | -1.8 | -1.7 | mV/℃ | -40℃ ≤ Tj ≤ 130℃ | 43 |
| Core voltage on VCORE pin | VCORE | | 1.35 | | V | | 27 |
| Capacitor connected between VDD and VSS | CVDD | | 10 | | uF | | 27 |
| Capacitor connected between VCORE and VSS | CVCORE | | 470 | | nF | | 27 |
| Junction-to-ambient thermal resistance (VQFN-48 RGZ) | RθJA | | 29.9 | | °C/W | | 28 |
| Junction-to-case (top) thermal resistance (VQFN-48 RGZ) | RθJC(top) | | 20.5 | | °C/W | | 28 |
| Junction-to-board thermal resistance (VQFN-48 RGZ) | RθJB | | 12.3 | | °C/W | | 28 |
| Junction-to-top characterization parameter (VQFN-48 RGZ) | ΨJT | | 0.4 | | °C/W | | 28 |
| Junction-to-board characterization parameter (VQFN-48 RGZ) | ΨJB | | 12.2 | | °C/W | | 28 |
| Junction-to-case (bottom) thermal resistance (VQFN-48 RGZ) | RθJC(bot) | | 4.1 | | °C/W | | 28 |
## CAD (KiCad official)
- Symbol: `M0G3507QRGZRQ1`
- Footprint: `Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm`
- 3D model: VQFN-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `m0g3507qrgzrq1-etched.step` / `m0g3507qrgzrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m0g3507qrgzrq1.step` / `m0g3507qrgzrq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/mspm0g3507-q1.pdf) (126 pp, sha256 `c44df29a9981ebcd`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m0g3507qrgzrq1-datasheet.pdf)