Generated by kicad-footprint-generator · KiCad file format 20260206
LV8961HUWR2G
onsemi · Motor Driver ICs · LQFP-48-EP(7x7)
LV8961HUWR2G from onsemi, in a LQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V3RO | power_out | 3 V regulator output pin; connect a capacitor between this pin and AGND. |
| 2 | V3RI | power_in | 3 V regulator input pin (internally connected to control and logic circuits); connect to the V3RO pin. |
| 3 | NC | unconnected | No connection. |
| 4 | DIAG | output | Programmable open drain diagnostic output. |
| 5 | VCC | power_out | 5 V or 3.3 V regulator output (selected by internal register setting) powering the microcontroller; connect a capacitor to AGND for stability. |
| 6 | RXD | output | Open drain logic level output of HVPIN received data; use a pull-up to a voltage less than or equal to VS. |
| 7 | AGND | power_in | Analog GND pin. |
| 8 | CSB | input | Active low SPI interface chip selection pin. |
| 9 | SCLK | input | SPI interface clock input pin. |
| 10 | SI | input | Active high SPI interface serial data input pin. |
| 11 | SO | output | Open drain SPI interface serial data output pin. |
| 12 | FG | output | Open drain BEMF transition output pin; frequency division ratio is selectable via register settings. |
| 13 | IGND | power_in | HV PWMIN block GND pin; must be connected to AGND on the PCB. |
| 14 | NC | unconnected | No connection. |
| 15 | HVPIN | input | High voltage PWM input with a VVS/2 threshold. |
| 16 | NC | unconnected | No connection. |
| 17 | LVPIN | input | Digital level PWM input pin for direct drive or speed register selection; input polarity programmable active high or active low. |
| 18 | TH | input | Thermistor input for power stage temperature detection; an error is triggered if input voltage is below the programmable threshold, tie to V3RO to disable. |
| 19 | RFSENS | input | Shunt resistance reference pin; connect to the GND side of the shunt resistor with Kelvin leads. |
| 20 | NC | unconnected | No connection. |
| 21 | RF | input | Output current detect pin; connect to the higher terminal of the shunt resistor with Kelvin leads. |
| 22 | NC | unconnected | No connection. |
| 23 | COM | input | COM input pin; connect to the motor neutral point if available, which may be derived from a resistive network with 1 kΩ resistors to the phases. |
| 24 | NC | unconnected | No connection. |
| 25 | SWL | passive | Current return path for the W-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin. |
| 26 | WL | output | Predriver output pin for the W-phase low-side NFET; use gate resistors for wave-shaping. |
| 27 | WOUT | passive | Current return path for the W-phase high-side predriver and reference for high-side short-circuit shutoff. |
| 28 | WH | output | Predriver output pin for the W-phase high-side NFET; use gate resistors for wave-shaping. |
| 29 | SVL | passive | Current return path for the V-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin. |
| 30 | VL | output | Predriver output pin for the V-phase low-side NFET; use gate resistors for wave-shaping. |
| 31 | VOUT | passive | Current return path for the V-phase high-side predriver and reference for high-side short-circuit shutoff. |
| 32 | VH | output | Predriver output pin for the V-phase high-side NFET; use gate resistors for wave-shaping. |
| 33 | SUL | passive | Current return path for the U-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin. |
| 34 | UL | output | Predriver output pin for the U-phase low-side NFET; use gate resistors for wave-shaping. |
| 35 | UOUT | passive | Current return path for the U-phase high-side predriver and reference for high-side short-circuit shutoff. |
| 36 | UH | output | Predriver output pin for the U-phase high-side NFET; use gate resistors for wave-shaping. |
| 37 | VDH | input | Sense input for supply voltage and short-circuit detection of high-side power FETs; connect through a 100 Ω resistor to the common drain of the power bridge. |
| 38 | PGND | power_in | GND pin for the charge pump. |
| 39 | VGL | power_out | Power supply pin for the low-side predriver; connect a decoupling capacitor between this pin and GND. |
| 40 | CHP | power_out | Power supply pin for the high-side predriver; connect a decoupling capacitor between this pin and VS. |
| 41 | CP1N | passive | Charge transfer pin of the charge pump (1N); connect a capacitor between CP1P and CP1N. |
| 42 | CP1P | passive | Charge transfer pin of the charge pump (1P); connect a capacitor between CP1P and CP1N. |
| 43 | CP2P | passive | Charge transfer pin of the charge pump (2P); connect a capacitor between CP2P and CP2N. |
| 44 | CP2N | passive | Charge transfer pin of the charge pump (2N); connect a capacitor between CP2P and CP2N. |
| 45 | TEST | input | Factory test pin; connect to GND. |
| 46 | VS | power_in | Power supply pin. |
| 47 | WAKE | input | WAKE pin: H = operating mode, L or open = sleep mode in which all predrivers are high impedance. |
| 48 | EN | input | Motor stage enable pin: H = normal enabled mode, L or open = standby mode with all predrivers driven low (motor freewheeling). |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | LQFP-48-EP(7x7) |
| Category | Power Supply Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VS | -0.3 | 40 | V | 10 | ||
| Sense Input for Supply Voltage | VDH | -0.3 | 40 | V | 10 | ||
| Charge Pump Voltage (High Side) | CHP | -0.3 | 40 | V | 10 | ||
| Charge Pump Voltage (Low Side) | VGL | -0.3 | 16 | V | 10 | ||
| 5 V Regulator Voltage | VCC | -0.3 | 5.5 | V | 10 | ||
| HVPIN PWMIN Voltage | HVPIN | -10 | 40 | V | 10 | ||
| Digital I/O Voltage1 | -0.3 | 40 | V | WAKE, EN | 10 | ||
| Digital I/O Voltage2 | -0.3 | 5.5 | V | CSB, SCLK, SI, LVPIN, TEST | 10 | ||
| Open Drain Output Current | 10 | mA | DIAG, FG, SO, RXD | 10 | |||
| Thermal Resistance (RjA) | RjA | 47 | °C/W | with board, 76.2 × 114.3 × 1.6 mm glass epoxy | 10 | ||
| ESD HBM | 2 | kV | AEC Q100-002 | 10 | |||
| ESD CDM | 750 | V | AEC Q100-011 | 10 | |||
| Storage Temperature | -55 | 150 | °C | 10 | |||
| Junction Temperature | -40 | 150 | °C | 10 | |||
| Supply-voltage Range | VS | 6 | 12 | 28 | V | Normal mode | 11 |
| Supply-voltage Range | VS | 5.5 | 28 | V | Device fully functional | 11 | |
| Supply-voltage Range | VS | 4.5 | 40 | V | Full logic functionality, driver stage off | 11 | |
| Operational junction Temperature | Topj | -40 | 150 | °C | 11 | ||
| Supply Current into VS | Is1 | 15 | 25 | mA | V3RO = V3RI, EN = L | 11 | |
| Supply Current into VS | Is2 | 40 | 80 | µA | Sleep Mode | 11 | |
| Low-side Output On-resistance 1 | RON(L1) | 6 | 15 | Ω | "L" level Io = 10mA | 11 | |
| Low-side Output On-resistance 2 | RON(L2) | 12 | 22 | Ω | "H" level Io = -10mA | 11 | |
| High-side Output On-resistance 1 | RON(H1) | 6 | 15 | Ω | "L" level Io = 10mA | 11 | |
| High-side Output On-resistance 2 | RON(H2) | 12 | 22 | Ω | "H" level Io = -10mA | 11 | |
| Drive Output PWM Frequency | fPWMO | 18.5 | 19.5 | 20.5 | kHz | 11 | |
| 3 V Output Voltage | V3RO | 3.135 | 3.3 | 3.465 | V | 11 | |
| Voltage Regulation | V3R1 | 50 | mV | VS = 6.0 to 28 V | 11 | ||
| Load Regulation | V3REG2 | 50 | mV | Io = 5 mA to 25 mA | 11 | ||
| Current Limit | IV3RO | 50 | mA | Not for external loads > 5 mA | 11 | ||
| VCC 5 V Output Voltage | VC5RO | 4.75 | 5 | 5.25 | V | VS = 6.0 to 28 V | 11 |
| VCC 5 V Voltage Regulation | VC5R1 | 50 | mV | VS = 6.0 to 28 V | 11 | ||
| VCC 5 V Load Regulation | VC5R2 | 50 | mV | Io = 5 mA to 25 mA | 11 | ||
| VCC 5 V Current Limit | IVCC5V | 50 | mA | 11 | |||
| VCC 3 V Output Voltage | VC3RO | 3.135 | 3.3 | 3.465 | V | 11 | |
| VCC 3 V Voltage Regulation | VC3R1 | 50 | mV | VS = 6.0 to 28 V | 11 | ||
| VCC 3 V Load Regulation | VC3R2 | 50 | mV | Io = 5 mA to 25 mA | 11 | ||
| VCC 3 V Current Limit | IVCC3V3 | 50 | mA | 11 | |||
| Low-side Output Voltage1 | VGLH1 | 8 | 12 | 14 | V | 6.0 <VS ≤ 8.0 V Io = -10 mA | 11 |
| Low-side Output Voltage2 | VGLH2 | 10 | 12 | 14 | V | 8.0 < VS ≤ 20 V Io = -10 mA | 11 |
| Low-side Output Voltage3 | VGLH3 | 7 | V | 20 < VS ≤ 28V Io = -10mA | 11 | ||
| Charge Pump Oscillator frequency | FCP | 49.6 | 52.1 | 54.6 | kHz | SSCG = 0 | 12 |
| CHP Voltage Limit | VCHPLIM | 34 | 36.5 | 38 | V | VS = 28 V | 12 |
| Input PWM Frequency Range (low freq) | fLPWM | 5.3 | 1000 | Hz | PWMF = 0, Low frequency mode | 12 | |
| PWM Signal Timeout | TLPWMIN | 210 | 220 | ms | PWMF = 0, Low frequency mode | 12 | |
| Input PWM Frequency Range (high freq) | fHPWM | 5.3 | 18500 | Hz | PWMF = 1, High frequency mode, PWMINSEL=1, LVPIN is used for PWM input | 12 | |
| Current Limit Voltage 1 | VRF11 | 40 | 50 | 60 | mV | Voltage between RF and RFSENS, CLSEL = 0 | 13 |
| Current Limit Voltage 2 | VRF12 | 90 | 100 | 110 | mV | Voltage between RF and RFSENS, CLSEL = 1 | 13 |
| Overcurrent Detection Threshold 1 | VRF21 | 15 | 25 | 35 | mV | OCSEL = 00 | 13 |
| Overcurrent Detection Threshold 4 | VRF24 | 90 | 100 | 110 | mV | OCSEL = 11 | 13 |
| VS Undervoltage Detection | VSLV | 4.8 | 5.1 | V | 13 | ||
| VS Overvoltage Detection | VSHV | 30.5 | 35.5 | V | 13 | ||
| Digital Output Low Voltage | VOL | 0.2 | V | Io = 1 mA pull-up current | 13 | ||
| Output Leakage Current | ILOLK | 10 | µA | 13 |
CAD (KiCad official)
- Symbol:
LV8961HUWR2G - Footprint:
Package_QFP:LQFP-48-1EP_7x7mm_P0.5mm_EP3.6x3.6mm - 3D model: LQFP-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
lv8961huwr2g-etched.step/lv8961huwr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lv8961huwr2g.step/lv8961huwr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (68 pp, sha256
234c481c4d4b3a7c, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).