Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LV8961HUWR2G

onsemi · Motor Driver ICs · LQFP-48-EP(7x7)

LV8961HUWR2G from onsemi, in a LQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 V3RO power_out 3 V regulator output pin; connect a capacitor between this pin and AGND.
2 V3RI power_in 3 V regulator input pin (internally connected to control and logic circuits); connect to the V3RO pin.
3 NC unconnected No connection.
4 DIAG output Programmable open drain diagnostic output.
5 VCC power_out 5 V or 3.3 V regulator output (selected by internal register setting) powering the microcontroller; connect a capacitor to AGND for stability.
6 RXD output Open drain logic level output of HVPIN received data; use a pull-up to a voltage less than or equal to VS.
7 AGND power_in Analog GND pin.
8 CSB input Active low SPI interface chip selection pin.
9 SCLK input SPI interface clock input pin.
10 SI input Active high SPI interface serial data input pin.
11 SO output Open drain SPI interface serial data output pin.
12 FG output Open drain BEMF transition output pin; frequency division ratio is selectable via register settings.
13 IGND power_in HV PWMIN block GND pin; must be connected to AGND on the PCB.
14 NC unconnected No connection.
15 HVPIN input High voltage PWM input with a VVS/2 threshold.
16 NC unconnected No connection.
17 LVPIN input Digital level PWM input pin for direct drive or speed register selection; input polarity programmable active high or active low.
18 TH input Thermistor input for power stage temperature detection; an error is triggered if input voltage is below the programmable threshold, tie to V3RO to disable.
19 RFSENS input Shunt resistance reference pin; connect to the GND side of the shunt resistor with Kelvin leads.
20 NC unconnected No connection.
21 RF input Output current detect pin; connect to the higher terminal of the shunt resistor with Kelvin leads.
22 NC unconnected No connection.
23 COM input COM input pin; connect to the motor neutral point if available, which may be derived from a resistive network with 1 kΩ resistors to the phases.
24 NC unconnected No connection.
25 SWL passive Current return path for the W-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin.
26 WL output Predriver output pin for the W-phase low-side NFET; use gate resistors for wave-shaping.
27 WOUT passive Current return path for the W-phase high-side predriver and reference for high-side short-circuit shutoff.
28 WH output Predriver output pin for the W-phase high-side NFET; use gate resistors for wave-shaping.
29 SVL passive Current return path for the V-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin.
30 VL output Predriver output pin for the V-phase low-side NFET; use gate resistors for wave-shaping.
31 VOUT passive Current return path for the V-phase high-side predriver and reference for high-side short-circuit shutoff.
32 VH output Predriver output pin for the V-phase high-side NFET; use gate resistors for wave-shaping.
33 SUL passive Current return path for the U-phase low-side predriver; short-circuit shutoff level is measured between this pin and its phase pin.
34 UL output Predriver output pin for the U-phase low-side NFET; use gate resistors for wave-shaping.
35 UOUT passive Current return path for the U-phase high-side predriver and reference for high-side short-circuit shutoff.
36 UH output Predriver output pin for the U-phase high-side NFET; use gate resistors for wave-shaping.
37 VDH input Sense input for supply voltage and short-circuit detection of high-side power FETs; connect through a 100 Ω resistor to the common drain of the power bridge.
38 PGND power_in GND pin for the charge pump.
39 VGL power_out Power supply pin for the low-side predriver; connect a decoupling capacitor between this pin and GND.
40 CHP power_out Power supply pin for the high-side predriver; connect a decoupling capacitor between this pin and VS.
41 CP1N passive Charge transfer pin of the charge pump (1N); connect a capacitor between CP1P and CP1N.
42 CP1P passive Charge transfer pin of the charge pump (1P); connect a capacitor between CP1P and CP1N.
43 CP2P passive Charge transfer pin of the charge pump (2P); connect a capacitor between CP2P and CP2N.
44 CP2N passive Charge transfer pin of the charge pump (2N); connect a capacitor between CP2P and CP2N.
45 TEST input Factory test pin; connect to GND.
46 VS power_in Power supply pin.
47 WAKE input WAKE pin: H = operating mode, L or open = sleep mode in which all predrivers are high impedance.
48 EN input Motor stage enable pin: H = normal enabled mode, L or open = standby mode with all predrivers driven low (motor freewheeling).
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer onsemi
Package LQFP-48-EP(7x7)
Category Power Supply Chip
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VS -0.3 40 V 10
Sense Input for Supply Voltage VDH -0.3 40 V 10
Charge Pump Voltage (High Side) CHP -0.3 40 V 10
Charge Pump Voltage (Low Side) VGL -0.3 16 V 10
5 V Regulator Voltage VCC -0.3 5.5 V 10
HVPIN PWMIN Voltage HVPIN -10 40 V 10
Digital I/O Voltage1 -0.3 40 V WAKE, EN 10
Digital I/O Voltage2 -0.3 5.5 V CSB, SCLK, SI, LVPIN, TEST 10
Open Drain Output Current 10 mA DIAG, FG, SO, RXD 10
Thermal Resistance (RjA) RjA 47 °C/W with board, 76.2 × 114.3 × 1.6 mm glass epoxy 10
ESD HBM 2 kV AEC Q100-002 10
ESD CDM 750 V AEC Q100-011 10
Storage Temperature -55 150 °C 10
Junction Temperature -40 150 °C 10
Supply-voltage Range VS 6 12 28 V Normal mode 11
Supply-voltage Range VS 5.5 28 V Device fully functional 11
Supply-voltage Range VS 4.5 40 V Full logic functionality, driver stage off 11
Operational junction Temperature Topj -40 150 °C 11
Supply Current into VS Is1 15 25 mA V3RO = V3RI, EN = L 11
Supply Current into VS Is2 40 80 µA Sleep Mode 11
Low-side Output On-resistance 1 RON(L1) 6 15 Ω "L" level Io = 10mA 11
Low-side Output On-resistance 2 RON(L2) 12 22 Ω "H" level Io = -10mA 11
High-side Output On-resistance 1 RON(H1) 6 15 Ω "L" level Io = 10mA 11
High-side Output On-resistance 2 RON(H2) 12 22 Ω "H" level Io = -10mA 11
Drive Output PWM Frequency fPWMO 18.5 19.5 20.5 kHz 11
3 V Output Voltage V3RO 3.135 3.3 3.465 V 11
Voltage Regulation V3R1 50 mV VS = 6.0 to 28 V 11
Load Regulation V3REG2 50 mV Io = 5 mA to 25 mA 11
Current Limit IV3RO 50 mA Not for external loads > 5 mA 11
VCC 5 V Output Voltage VC5RO 4.75 5 5.25 V VS = 6.0 to 28 V 11
VCC 5 V Voltage Regulation VC5R1 50 mV VS = 6.0 to 28 V 11
VCC 5 V Load Regulation VC5R2 50 mV Io = 5 mA to 25 mA 11
VCC 5 V Current Limit IVCC5V 50 mA 11
VCC 3 V Output Voltage VC3RO 3.135 3.3 3.465 V 11
VCC 3 V Voltage Regulation VC3R1 50 mV VS = 6.0 to 28 V 11
VCC 3 V Load Regulation VC3R2 50 mV Io = 5 mA to 25 mA 11
VCC 3 V Current Limit IVCC3V3 50 mA 11
Low-side Output Voltage1 VGLH1 8 12 14 V 6.0 <VS ≤ 8.0 V Io = -10 mA 11
Low-side Output Voltage2 VGLH2 10 12 14 V 8.0 < VS ≤ 20 V Io = -10 mA 11
Low-side Output Voltage3 VGLH3 7 V 20 < VS ≤ 28V Io = -10mA 11
Charge Pump Oscillator frequency FCP 49.6 52.1 54.6 kHz SSCG = 0 12
CHP Voltage Limit VCHPLIM 34 36.5 38 V VS = 28 V 12
Input PWM Frequency Range (low freq) fLPWM 5.3 1000 Hz PWMF = 0, Low frequency mode 12
PWM Signal Timeout TLPWMIN 210 220 ms PWMF = 0, Low frequency mode 12
Input PWM Frequency Range (high freq) fHPWM 5.3 18500 Hz PWMF = 1, High frequency mode, PWMINSEL=1, LVPIN is used for PWM input 12
Current Limit Voltage 1 VRF11 40 50 60 mV Voltage between RF and RFSENS, CLSEL = 0 13
Current Limit Voltage 2 VRF12 90 100 110 mV Voltage between RF and RFSENS, CLSEL = 1 13
Overcurrent Detection Threshold 1 VRF21 15 25 35 mV OCSEL = 00 13
Overcurrent Detection Threshold 4 VRF24 90 100 110 mV OCSEL = 11 13
VS Undervoltage Detection VSLV 4.8 5.1 V 13
VS Overvoltage Detection VSHV 30.5 35.5 V 13
Digital Output Low Voltage VOL 0.2 V Io = 1 mA pull-up current 13
Output Leakage Current ILOLK 10 µA 13

CAD (KiCad official)

  • Symbol: LV8961HUWR2G
  • Footprint: Package_QFP:LQFP-48-1EP_7x7mm_P0.5mm_EP3.6x3.6mm
  • 3D model: LQFP-48-EP(7x7) (KiCad packages3D, STEP)
  • 3D model files: lv8961huwr2g-etched.step / lv8961huwr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lv8961huwr2g.step / lv8961huwr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (68 pp, sha256 234c481c4d4b3a7c, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF