3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLTC7819RUJ#TRPBF
Analog Devices · DC-DC Converters · QFN-40(6x6)
LTC7819RUJ#TRPBF from Analog Devices, in a QFN-40(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Mode select input acting on all three channels: grounding it selects Burst Mode, tying it to INTVCC selects forced continuous mode, and a 100k resistor from it to INTVCC selects pulse-skipping; it is Burst Mode when floating because of an internal 100k pull-down. |
| 2 | TRACK/SS1 | input | Channel 1 external tracking and soft-start input, with a 12.5µA internal pull-up that charges an external capacitor to set the startup ramp (0.65ms per 10nF), and the EA− reference is the lesser of 0.8V or this pin's voltage. |
| 3 | SENSE1- | input | Negative input to the channel 1 differential current comparator; when it is 3.2V or greater it supplies most of the sleep-mode quiescent current instead of VIN, and it supplies comparator current when above INTVCC. |
| 4 | SENSE1+ | input | Positive input to the channel 1 differential current comparator, where the ITH voltage and controlled offsets between SENSE− and SENSE+ set the current trip threshold in conjunction with RSENSE. |
| 5 | VFB1 | input | Channel 1 feedback input: when VPRG1 is floating, an external resistor divider from the output sets the regulated voltage; when VPRG1 is tied to GND or INTVCC, VFB1 is tied directly to the output. |
| 6 | ITH1 | passive | Channel 1 error amplifier output and regulator compensation point, where the control voltage sets the channel's current comparator trip point and compensation components are placed between ITH and ground. |
| 7 | PGOOD2 | output | Open-drain power good output for channel 2, pulled low when VFB2 is not within ±10% of its regulation point. |
| 8 | RUN3 | input | Run control input for channel 3: forcing it below 1.1V disables that channel's switching, and it can be tied to VIN for always-on operation. |
| 9 | RUN2 | input | Run control input for channel 2: forcing it below 1.1V disables that channel's switching, and forcing all three RUN pins below 0.7V shuts down the entire LTC7819 to about 1.5µA quiescent current. |
| 10 | RUN1 | input | Run control input for channel 1: forcing it below 1.1V disables that channel's switching, and forcing all three RUN pins below 0.7V shuts down the entire LTC7819 to about 1.5µA quiescent current. |
| 11 | SENSE2- | input | Negative input to the channel 2 differential current comparator, which supplies comparator current when its voltage is above INTVCC. |
| 12 | SENSE2+ | input | Positive input to the channel 2 differential current comparator, where the ITH voltage and controlled offsets between SENSE− and SENSE+ set the current trip threshold in conjunction with RSENSE. |
| 13 | VFB2 | input | Channel 2 feedback input for an external resistor divider from the output; tying it to INTVCC configures channel 2 as a slave to channel 1 in a multi-phase single output application. |
| 14 | ITH2 | passive | Channel 2 error amplifier output and regulator compensation point, where the control voltage sets the channel's current comparator trip point and compensation components are placed between ITH and ground. |
| 15 | TRACK/SS2 | input | Channel 2 external tracking and soft-start input, with a 12.5µA internal pull-up that charges an external capacitor to set the startup ramp, and the EA− reference is the lesser of 0.8V or this pin's voltage. |
| 16 | VPRG1 | input | Channel 1 voltage programming pin: floating allows adjustable output through VFB1 to the 0.8V reference, while GND or INTVCC programs the output to 3.3V or 5V respectively with VFB1 connected directly to the output. |
| 17 | PGOOD1 | output | Open-drain power good output for channel 1, pulled low when VFB1 is not within ±10% of its regulation point. |
| 18 | TG2 | output | High-current gate drive for the channel 2 top N-channel MOSFET, a floating driver output with a voltage swing of INTVCC superimposed on the SW2 node. |
| 19 | SW2 | passive | Channel 2 switch node connection to the inductor. |
| 20 | BOOST2 | power_out | Bootstrapped supply for the channel 2 top-side floating driver, with a capacitor to SW2 and a Schottky diode from INTVCC; the swing runs from INTVCC to (VIN+INTVCC). |
| 21 | BG2 | output | High-current gate drive for the channel 2 bottom N-channel MOSFET, swinging from ground to INTVCC. |
| 22 | INTVCC | power_out | Output of the internal 5.1V low dropout regulator that powers the drivers and control circuits, which must be decoupled to ground with a minimum of 4.7µF ceramic or tantalum capacitor. |
| 23 | EXTVCC | power_in | External power input to an internal LDO connected to INTVCC that bypasses the VIN LDO when EXTVCC is higher than 4.7V; do not exceed 30V on this pin, and connect it to ground if the EXTVCC LDO is not used. |
| 24 | VIN | power_in | Main bias input supply pin, with a bypass capacitor tied between this pin and ground. |
| 25 | BG1 | output | High-current gate drive for the channel 1 bottom N-channel MOSFET, swinging from ground to INTVCC. |
| 26 | BOOST1 | power_out | Bootstrapped supply for the channel 1 top-side floating driver, with a capacitor to SW1 and a Schottky diode from INTVCC; the swing runs from INTVCC to (VIN+INTVCC). |
| 27 | TG1 | output | High-current gate drive for the channel 1 top N-channel MOSFET, a floating driver output with a voltage swing of INTVCC superimposed on the SW1 node. |
| 28 | SW1 | passive | Channel 1 switch node connection to the inductor. |
| 29 | BG3 | output | High-current gate drive for the channel 3 bottom N-channel MOSFET, swinging from ground to INTVCC. |
| 30 | BOOST3 | power_out | Bootstrapped supply for the channel 3 top-side floating driver, with a capacitor to SW3 and a Schottky diode from INTVCC; the swing runs from INTVCC to (VIN+INTVCC). |
| 31 | SW3 | passive | Channel 3 switch node connection to the inductor. |
| 32 | TG3 | output | High-current gate drive for the channel 3 top N-channel MOSFET, a floating driver output with a voltage swing of INTVCC superimposed on the SW3 node. |
| 33 | PGOOD3 | output | Open-drain power good output for channel 3, pulled low when VFB3 is not within ±10% of its regulation point. |
| 34 | PLLIN/SPREAD | input | External synchronization input and spread spectrum select: an applied external clock synchronizes the rising TG1 edge, while tying it to INTVCC enables spread spectrum dithering and tying it to ground disables spread spectrum when not synchronizing. |
| 35 | TRACK/SS3 | input | Channel 3 external tracking and soft-start input, with a 12.5µA internal pull-up that charges an external capacitor to set the startup ramp, and the EA− reference is the lesser of 0.8V or this pin's voltage. |
| 36 | ITH3 | passive | Channel 3 error amplifier output and regulator compensation point, where the control voltage sets the channel's current comparator trip point and compensation components are placed between ITH and ground. |
| 37 | VFB3 | input | Channel 3 feedback input for an external resistor divider from the output; tying it to INTVCC configures channel 3 as a slave to channel 1 in a multi-phase single output application. |
| 38 | SENSE3+ | input | Positive input to the channel 3 differential current comparator, where the ITH voltage and controlled offsets between SENSE− and SENSE+ set the current trip threshold in conjunction with RSENSE. |
| 39 | SENSE3- | input | Negative input to the channel 3 differential current comparator, which supplies comparator current when its voltage is above INTVCC. |
| 40 | FREQ | input | Frequency control pin for the internal oscillator: GND sets 380kHz, INTVCC sets 2.25MHz, a resistor to GND programs 100kHz to 3MHz, and the capacitance on this pin should be minimized. |
| 41 | GND | power_in | Exposed pad ground that connects to the sources of the bottom N-channel MOSFETs and the negative terminals of decoupling capacitors, and must be soldered to PCB ground for rated electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-40(6x6) |
| Category | Power Management |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage (VIN) absolute maximum | -0.3 | 40 | V | 2 | |||
| BOOST1, BOOST2, BOOST3 voltage | -0.3 | 46 | V | 2 | |||
| Switch voltage (SW1, SW2, SW3) | -5 | 40 | V | 2 | |||
| RUN1, RUN2, RUN3 voltages | -0.3 | 40 | V | 2 | |||
| EXTVCC voltage | -0.3 | 30 | V | 2 | |||
| INTVCC voltage | -0.3 | 6 | V | 2 | |||
| (BOOST1-SW1), (BOOST2-SW2), (BOOST3-SW3) voltage | -0.3 | 6 | V | 2 | |||
| SENSE1+, SENSE1-, SENSE2+, SENSE2-, SENSE3+, SENSE3- voltages | -0.3 | 40 | V | 2 | |||
| TRACK/SS1,2,3 and VFB1,2,3 voltages | -0.3 | 6 | V | 2 | |||
| ITH1, ITH2, ITH3 voltages | -0.3 | 2 | V | 2 | |||
| MODE, PGOOD1, PGOOD2 voltages | -0.3 | 6 | V | 2 | |||
| PGOOD3, VPRG1 voltages | -0.3 | 6 | V | 2 | |||
| PLLIN/SPREAD, FREQ voltages | -0.3 | 6 | V | 2 | |||
| Operating junction temperature range (LTC7819R) | -40 | 150 | °C | 2 | |||
| Storage temperature range | -65 | 150 | °C | 2 | |||
| Maximum junction temperature (TJ) | TJ | 150 | °C | 2 | |||
| VIN input supply operating range | VIN | 4.5 | 40 | V | 3 | ||
| VOUT1,2,3 output voltage operating range | VOUT1,2,3 | 0.8 | 40 | V | 3 | ||
| VFB1,2,3 regulated adjustable output feedback voltage | VFB1,2,3 | 0.788 | 0.8 | 0.812 | V | VIN = 4.5V to 40V, ITH1,2,3 Voltage = 0.6V to 1.2V, 0°C to 85°C | 3 |
| VFB1,2,3 regulated adjustable output feedback voltage (second row) | VFB1,2,3 | 0.792 | 0.8 | 0.808 | V | VIN = 4.5V to 40V, ITH1,2,3 Voltage = 0.6V to 1.2V | 3 |
| VFB1 regulated fixed output feedback voltage (VPRG1 = 0V, 3.3V) | VFB1 | 3.23 | 3.3 | 3.37 | V | VIN = 4.5V to 40V, ITH1 Voltage = 0.6V to 1.2V, VPRG1 = 0V | 3 |
| VFB1 regulated fixed output feedback voltage (VPRG1 = INTVCC, 5V) | VFB1 | 4.9 | 5 | 5.1 | V | VIN = 4.5V to 40V, ITH1 Voltage = 0.6V to 1.2V, VPRG1 = INTVCC | 3 |
| Feedback current (channels 2 and 3) | -50 | 5 | 50 | nA | 3 | ||
| Feedback current (channel 1), VPRG1 = FLOAT | -50 | 5 | 50 | nA | VPRG1 = FLOAT | 3 | |
| Feedback overvoltage protection threshold | 7 | 10 | 13 | % | Measured at VFB1,2,3 relative to regulated VFB1,2,3 | 3 | |
| Maximum current sense threshold VSENSE(MAX) | VSENSE(MAX) | 45 | 50 | 55 | mV | VFB1,2,3 = 0.7V, VSENSE1,2,3- = 3.3V | 3 |
| Matching between channels | -3.5 | 0 | 3.5 | mV | VSENSE1,2,3- = 3.3V | 3 | |
| ISENSE1,2,3+ pin current | ISENSE1,2,3+ | -1 | 1 | µA | VSENSE1,2,3+ = 3.3V | 3 | |
| Soft-start charge current | 10 | 12.5 | 15 | µA | VTRACK/SS1,2,3 = 0V | 3 | |
| RUN pin ON threshold | VRUN1,2,3 | 1.15 | 1.2 | 1.25 | V | VRUN1,2,3 rising | 3 |
| VIN sleep mode current, one channel on | 15 | 24 | µA | VSENSE1- < 3.2V, EXTVCC = 0V, one channel on | 3 | ||
| VIN sleep mode current, all channels on | 18 | 30 | µA | VSENSE1- < 3.2V, EXTVCC = 0V, all channels on | 3 | ||
| Sleep mode current, only channel 1 on: VIN current | 5 | 9 | µA | VSENSE1- ≥ 3.2V, EXTVCC = 0V | 3 | ||
| Sleep mode current, only channel 1 on: VIN current | 1 | 4 | µA | VSENSE1- ≥ 3.2V, EXTVCC ≥ 4.8V | 3 | ||
| Sleep mode current, only channel 1 on: EXTVCC current | 5 | 10 | µA | VSENSE1- ≥ 3.2V, EXTVCC ≥ 4.8V | 3 | ||
| Sleep mode current, only channel 1 on: SENSE1- current | 10 | 18 | µA | VSENSE1- ≥ 3.2V | 3 | ||
| Sleep mode current, all channels on: VIN current | 1 | 4 | µA | VSENSE1- ≥ 3.2V, EXTVCC ≥ 4.8V | 3 | ||
| Sleep mode current, all channels on: EXTVCC current | 8 | 14 | µA | VSENSE1- ≥ 3.2V, EXTVCC ≥ 4.8V | 3 | ||
| Sleep mode current, all channels on: SENSE1- current | 16 | 26 | µA | VSENSE1- ≥ 3.2V, EXTVCC ≥ 4.8V | 3 | ||
| INTVCC regulation point | 4.9 | 5.1 | 5.3 | V | 4 | ||
| INTVCC load regulation (VIN ≥ 6V) | 1.2 | 2 | % | ICC = 0mA to 100mA, VIN ≥ 6V | 4 | ||
| INTVCC load regulation (VEXTVCC ≥ 6V) | 1.2 | 2 | % | ICC = 0mA to 100mA, VEXTVCC ≥ 6V | 4 | ||
| EXTVCC LDO switchover voltage | 4.5 | 4.7 | 4.8 | V | EXTVCC rising | 4 | |
| UVLO threshold, INTVCC rising | 4.1 | 4.2 | 4.35 | V | INTVCC rising | 4 | |
| UVLO threshold, INTVCC falling | 3.75 | 3.9 | 4 | V | INTVCC falling | 4 | |
| Low fixed oscillator frequency fOSC | fOSC | 330 | 380 | 430 | kHz | VFREQ = 0V, PLLIN/SPREAD = 0V | 4 |
| High fixed oscillator frequency fOSC | fOSC | 2 | 2.25 | 2.5 | MHz | VFREQ = INTVCC, PLLIN/SPREAD = 0V | 4 |
| Programmable oscillator frequency | fOSC | 450 | 500 | 550 | kHz | RFREQ = 75kΩ, PLLIN/SPREAD = 0V | 4 |
| Synchronizable frequency range | 0.1 | 3 | MHz | PLLIN/SPREAD = external clock | 4 | ||
| PLLIN input high level | 2.2 | V | 4 | ||||
| PLLIN input low level | 0.5 | V | 4 | ||||
| Spread spectrum minimum frequency (relative to fOSC) | 0 | % | PLLIN/SPREAD = INTVCC | 4 | |||
| Spread spectrum maximum frequency (relative to fOSC) | 20 | % | PLLIN/SPREAD = INTVCC | 4 | |||
| PGOOD voltage low | 0.2 | 0.4 | V | IPGOOD = 2mA | 4 | ||
| PGOOD leakage current | -1 | 1 | µA | VPGOOD = 5V | 4 | ||
| PGOOD trip level, VFB rising | 7 | 10 | 13 | % | VFB relative to set regulation point, VFB rising | 4 | |
| PGOOD trip level, VFB falling | -13 | -10 | -7 | % | VFB relative to set regulation point, VFB falling | 4 | |
| Thermal resistance junction-to-ambient θJA (UJ package) | θJA | 33 | °C/W | 2 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
LTC7819RUJ#TRPBF - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: QFN-40(6x6), generated on the KiCad land (body 6 x 6 mm, terminals on the pads, 0.7 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ltc7819ruj-etched.step/ltc7819ruj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc7819ruj.step/ltc7819ruj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (36 pp, sha256
31e56a534f080048, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).