main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ltc7000imse-pbf: viewers · Ray
ltc7000imse-pbf-etched.glb Publish 0.1.0 · Ray
ltc7000imse-pbf-etched.step ltc7000imse-pbf: factory component page (tier=mfr) · Ray
ltc7000imse-pbf-hero.glb ltc7000imse-pbf: hero GLB from the etched model (keeps the MPN mark) · Ray
ltc7000imse-pbf-hero.overlay.json Publish 0.1.0 · Ray
ltc7000imse-pbf.glb Publish 0.1.0 · Ray
ltc7000imse-pbf.kicad_mod Publish 0.1.0 · Ray
ltc7000imse-pbf.kicad_sym Publish 0.1.0 · Ray
ltc7000imse-pbf.lbr Publish 0.1.0 · Ray
ltc7000imse-pbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 17 pins · Ray

LTC7000IMSE#PBF

Analog Devices · Gate Drive ICs · MSOP-16-EP

LTC7000IMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RUN input Run control input: above 1.21V enables normal operation, below 0.7V shuts down the part to about 1µA quiescent current, and it can be connected to the input supply through a resistive divider to set the undervoltage lockout.
2 VIN power_in Main supply pin, operating range 3.5V to 135V (150V abs max), requiring a bypass capacitor of at least 0.1µF to GND.
3 VCC power_out Internal LDO output and supply for the gate drivers and internal circuitry, decoupled with at least 1.0µF low ESR ceramic to GND, can be overdriven externally but never to a voltage greater than VIN.
4 VCCUV input VCC undervoltage lockout set pin: 0.4V to 1.5V is multiplied by 7 to set the gate drive UVLO, short to ground for 3.5V minimum, leave open for 7.0V.
5 FAULT output Open-drain fault output with about 200Ω typical pull-down that pulls low after TIMER reaches the 1.3V fault threshold, indicating an impending turn-off from overcurrent.
6 TIMER passive Fault timer input where a capacitor to GND sets fault warning, turn-off and retry periods; a voltage above 3.5V disables the timer and makes an overcurrent immediately pull TGDN to TS.
7 INP input CMOS compatible input referenced to GND that sets the state of TGDN and TGUP, with an internal 1MΩ pull-down to GND.
8 OVLO input Overvoltage lockout input: above 1.21V pulls TGDN to TS and normal operation resumes below 1.11V; tie to GND when not used.
9 ISET input Current trip threshold set: a resistor to GND sets the peak current threshold with the pin voltage (clamped 0.4V to 1.5V) divided by 20, short to GND for 20mV or leave open for 30mV ΔVTH.
10 IMON output Current monitor output whose voltage with respect to GND equals the sense resistor voltage multiplied by 20, ranging from 0V to 1.5V.
11 TGDN output High current gate driver pull-down to TS; tie directly to the gate of the external high side MOSFET for the fastest turn-off.
12 TGUP output High current gate driver pull-up to BST; tie to TGDN for maximum transition speed or use a series resistor to the MOSFET gate to control turn-on in-rush current.
13 TS passive Top (high side) source connection of the external MOSFET, or GND in ground referenced applications.
14 BST power_in High side bootstrapped supply requiring at least 0.1µF to TS, with a voltage swing of 12V to (VIN + 12V).
15 SNS- input Current sense comparator input, connected to the sense resistor through a minimum 100Ω resistor.
16 SNS+ input Current sense comparator input connected with a Kelvin connection to the sense resistor placed in series with the MOSFET drain; trip threshold is clamped between 20mV and 75mV.
17 GND power_in Ground exposed pad that must be soldered to the PCB for rated electrical and thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Input Voltage Operating Range VIN 3.5 150 V 5
TS Operating Voltage Range 0 135 V 5
SNS+/- Input Voltage Range 3.5 150 V Independent of VIN 5
VBST-TS VBST-TS 9 10 14 V VIN = VCC = VTS = 7V, IBST = 0µA 5
VBST-TS VBST-TS 10 11 14 V VIN = VCC = VTS = 10V, IBST = 0µA 5
VBST-TS VBST-TS 10 12 14 V VIN = VTS = 135V, IBST = 0µA 5
Charge Pump Output Current -30 -15 µA VTS = 20V, VBST-TS = 10V 5
TG Pull-Up Resistance 2.2 7 Ω VIN = VBST = 12V 5
TG Pull-Down Resistance 1 4 Ω VIN = VBST = 12V 5
Input to Output Propagation Delay tPLH 35 70 ns VINP Rising, CL = 1nF 5
Input Threshold Voltage Rising VIH 1.7 2 2.2 V VINP Rising 6
Input Threshold Voltage Falling VIL 1.3 1.6 1.8 V VINP Falling 6
RUN and OVLO Threshold Rising 1.16 1.21 1.26 V Rising 6
RUN and OVLO Threshold Falling 1.05 1.1 1.15 V Falling 6
RUN and OVLO Leakage Current -100 0 100 nA VRUN = 1.3V, VOVLO = 1.3V 6
TIMER Threshold Voltage 1.25 1.3 1.35 V VTIMER Rising to VFAULT Going Low 6
TIMER Early Warning Voltage 75 100 125 mV VFAULT Going Low to (TG-TS) Going Low 6
TIMER Pin Fault Pull-Up Current -115 -100 -80 µA VTIMER = 1.0V, ISET = OPEN 6
TIMER Pin Pull-Down Current 2 2.5 3 µA VTIMER = 0.6V ISET = OPEN, ΔVSNS = 0mV 6
FAULT Output Low Voltage 0.2 0.5 V IFAULT = 1mA 6
FAULT Leakage Current -100 0 100 nA VFAULT = 5V 6
Current Sense Threshold Voltage ΔVTH 22 30 36 mV ISET = OPEN 6
Current Sense Threshold Voltage ΔVTH 54 60 64 mV VISET = 1.2V (LTC7000 Only) 6
Current Sense Threshold Voltage ΔVTH 15 20 24 mV VISET = 0V (LTC7000 Only) 6
Retry Duty Cycle D 0.06 0.1 % ΔVSNS = 200mV, CTIMER = 1nF 6
ISET and VCCUV Pull-Up Current -11.3 -10 -8.7 µA VISET = 1.0V, VCCUV = 1.0V 6
IMON Output Voltage 1.12 1.2 1.28 V ΔVSNS = 60mV, VTIMER = 0V, VINP = 3.5V 6
IMON Output Voltage 0.52 0.6 0.68 V ΔVSNS = 30mV, VTIMER = 0V, VINP = 3.5V 6
IMON Output Voltage 0 0.1 V ΔVSNS = 0mV, VTIMER = 0V, VINP = 3.5V 6
VIN Voltage VIN -0.3 150 V 3
BST-TS Voltage BST-TS -0.3 15 V 3
VCC Voltage VCC -0.3 15 V 3
TS Voltage TS -6 150 V 3
BST, SNS+ and SNS- Voltages -0.3 150 V 3
SNS+ - SNS- Continuous -0.3 0.3 V Continuous 3
SNS+ - SNS- Current -100 100 mA <1ms 3
INP Voltage -6 15 V 3
TIMER, FAULT Voltages -0.3 15 V 3
VCCUV Voltage -0.3 6 V 3
RUN Voltage -0.3 150 V LTC7000 3
ISET, IMON, OVLO Voltages -0.3 6 V LTC7000 3
Operating Junction Temperature Range TJ -40 125 °C LTC7000I 3
Storage Temperature Range -65 150 °C 3
Maximum Junction Temperature TJMAX 150 °C 3
Junction-to-Ambient Thermal Resistance θJA 45 °C/W 3
Junction-to-Case Thermal Resistance θJC 10 °C/W 3

CAD (KiCad official)

  • Symbol: LTC7000IMSE#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: ltc7000imse-pbf-etched.step / ltc7000imse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc7000imse-pbf.step / ltc7000imse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 4afedeccf3f70dd9, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF