3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC7000IMSE#PBF
Analog Devices · Gate Drive ICs · MSOP-16-EP
LTC7000IMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RUN | input | Run control input: above 1.21V enables normal operation, below 0.7V shuts down the part to about 1µA quiescent current, and it can be connected to the input supply through a resistive divider to set the undervoltage lockout. |
| 2 | VIN | power_in | Main supply pin, operating range 3.5V to 135V (150V abs max), requiring a bypass capacitor of at least 0.1µF to GND. |
| 3 | VCC | power_out | Internal LDO output and supply for the gate drivers and internal circuitry, decoupled with at least 1.0µF low ESR ceramic to GND, can be overdriven externally but never to a voltage greater than VIN. |
| 4 | VCCUV | input | VCC undervoltage lockout set pin: 0.4V to 1.5V is multiplied by 7 to set the gate drive UVLO, short to ground for 3.5V minimum, leave open for 7.0V. |
| 5 | FAULT | output | Open-drain fault output with about 200Ω typical pull-down that pulls low after TIMER reaches the 1.3V fault threshold, indicating an impending turn-off from overcurrent. |
| 6 | TIMER | passive | Fault timer input where a capacitor to GND sets fault warning, turn-off and retry periods; a voltage above 3.5V disables the timer and makes an overcurrent immediately pull TGDN to TS. |
| 7 | INP | input | CMOS compatible input referenced to GND that sets the state of TGDN and TGUP, with an internal 1MΩ pull-down to GND. |
| 8 | OVLO | input | Overvoltage lockout input: above 1.21V pulls TGDN to TS and normal operation resumes below 1.11V; tie to GND when not used. |
| 9 | ISET | input | Current trip threshold set: a resistor to GND sets the peak current threshold with the pin voltage (clamped 0.4V to 1.5V) divided by 20, short to GND for 20mV or leave open for 30mV ΔVTH. |
| 10 | IMON | output | Current monitor output whose voltage with respect to GND equals the sense resistor voltage multiplied by 20, ranging from 0V to 1.5V. |
| 11 | TGDN | output | High current gate driver pull-down to TS; tie directly to the gate of the external high side MOSFET for the fastest turn-off. |
| 12 | TGUP | output | High current gate driver pull-up to BST; tie to TGDN for maximum transition speed or use a series resistor to the MOSFET gate to control turn-on in-rush current. |
| 13 | TS | passive | Top (high side) source connection of the external MOSFET, or GND in ground referenced applications. |
| 14 | BST | power_in | High side bootstrapped supply requiring at least 0.1µF to TS, with a voltage swing of 12V to (VIN + 12V). |
| 15 | SNS- | input | Current sense comparator input, connected to the sense resistor through a minimum 100Ω resistor. |
| 16 | SNS+ | input | Current sense comparator input connected with a Kelvin connection to the sense resistor placed in series with the MOSFET drain; trip threshold is clamped between 20mV and 75mV. |
| 17 | GND | power_in | Ground exposed pad that must be soldered to the PCB for rated electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Input Voltage Operating Range | VIN | 3.5 | 150 | V | 5 | ||
| TS Operating Voltage Range | 0 | 135 | V | 5 | |||
| SNS+/- Input Voltage Range | 3.5 | 150 | V | Independent of VIN | 5 | ||
| VBST-TS | VBST-TS | 9 | 10 | 14 | V | VIN = VCC = VTS = 7V, IBST = 0µA | 5 |
| VBST-TS | VBST-TS | 10 | 11 | 14 | V | VIN = VCC = VTS = 10V, IBST = 0µA | 5 |
| VBST-TS | VBST-TS | 10 | 12 | 14 | V | VIN = VTS = 135V, IBST = 0µA | 5 |
| Charge Pump Output Current | -30 | -15 | µA | VTS = 20V, VBST-TS = 10V | 5 | ||
| TG Pull-Up Resistance | 2.2 | 7 | Ω | VIN = VBST = 12V | 5 | ||
| TG Pull-Down Resistance | 1 | 4 | Ω | VIN = VBST = 12V | 5 | ||
| Input to Output Propagation Delay | tPLH | 35 | 70 | ns | VINP Rising, CL = 1nF | 5 | |
| Input Threshold Voltage Rising | VIH | 1.7 | 2 | 2.2 | V | VINP Rising | 6 |
| Input Threshold Voltage Falling | VIL | 1.3 | 1.6 | 1.8 | V | VINP Falling | 6 |
| RUN and OVLO Threshold Rising | 1.16 | 1.21 | 1.26 | V | Rising | 6 | |
| RUN and OVLO Threshold Falling | 1.05 | 1.1 | 1.15 | V | Falling | 6 | |
| RUN and OVLO Leakage Current | -100 | 0 | 100 | nA | VRUN = 1.3V, VOVLO = 1.3V | 6 | |
| TIMER Threshold Voltage | 1.25 | 1.3 | 1.35 | V | VTIMER Rising to VFAULT Going Low | 6 | |
| TIMER Early Warning Voltage | 75 | 100 | 125 | mV | VFAULT Going Low to (TG-TS) Going Low | 6 | |
| TIMER Pin Fault Pull-Up Current | -115 | -100 | -80 | µA | VTIMER = 1.0V, ISET = OPEN | 6 | |
| TIMER Pin Pull-Down Current | 2 | 2.5 | 3 | µA | VTIMER = 0.6V ISET = OPEN, ΔVSNS = 0mV | 6 | |
| FAULT Output Low Voltage | 0.2 | 0.5 | V | IFAULT = 1mA | 6 | ||
| FAULT Leakage Current | -100 | 0 | 100 | nA | VFAULT = 5V | 6 | |
| Current Sense Threshold Voltage | ΔVTH | 22 | 30 | 36 | mV | ISET = OPEN | 6 |
| Current Sense Threshold Voltage | ΔVTH | 54 | 60 | 64 | mV | VISET = 1.2V (LTC7000 Only) | 6 |
| Current Sense Threshold Voltage | ΔVTH | 15 | 20 | 24 | mV | VISET = 0V (LTC7000 Only) | 6 |
| Retry Duty Cycle | D | 0.06 | 0.1 | % | ΔVSNS = 200mV, CTIMER = 1nF | 6 | |
| ISET and VCCUV Pull-Up Current | -11.3 | -10 | -8.7 | µA | VISET = 1.0V, VCCUV = 1.0V | 6 | |
| IMON Output Voltage | 1.12 | 1.2 | 1.28 | V | ΔVSNS = 60mV, VTIMER = 0V, VINP = 3.5V | 6 | |
| IMON Output Voltage | 0.52 | 0.6 | 0.68 | V | ΔVSNS = 30mV, VTIMER = 0V, VINP = 3.5V | 6 | |
| IMON Output Voltage | 0 | 0.1 | V | ΔVSNS = 0mV, VTIMER = 0V, VINP = 3.5V | 6 | ||
| VIN Voltage | VIN | -0.3 | 150 | V | 3 | ||
| BST-TS Voltage | BST-TS | -0.3 | 15 | V | 3 | ||
| VCC Voltage | VCC | -0.3 | 15 | V | 3 | ||
| TS Voltage | TS | -6 | 150 | V | 3 | ||
| BST, SNS+ and SNS- Voltages | -0.3 | 150 | V | 3 | |||
| SNS+ - SNS- Continuous | -0.3 | 0.3 | V | Continuous | 3 | ||
| SNS+ - SNS- Current | -100 | 100 | mA | <1ms | 3 | ||
| INP Voltage | -6 | 15 | V | 3 | |||
| TIMER, FAULT Voltages | -0.3 | 15 | V | 3 | |||
| VCCUV Voltage | -0.3 | 6 | V | 3 | |||
| RUN Voltage | -0.3 | 150 | V | LTC7000 | 3 | ||
| ISET, IMON, OVLO Voltages | -0.3 | 6 | V | LTC7000 | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LTC7000I | 3 | |
| Storage Temperature Range | -65 | 150 | °C | 3 | |||
| Maximum Junction Temperature | TJMAX | 150 | °C | 3 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 45 | °C/W | 3 | |||
| Junction-to-Case Thermal Resistance | θJC | 10 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
LTC7000IMSE#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
ltc7000imse-pbf-etched.step/ltc7000imse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc7000imse-pbf.step/ltc7000imse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
4afedeccf3f70dd9, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).