main
Ray
Publish 0.1.0
efcc11c
LTC7000ARMSE#TRPBF
Analog Devices · Gate Drive ICs · MSOP-16-EP
LTC7000ARMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RUN | input | Run control input: above 1.21V enables normal operation, below 0.7V shuts down the part (about 1µA quiescent), and it can be tied to the input supply through a resistive divider to set the undervoltage lockout. |
| 2 | VIN | power_in | Main supply pin, which needs a bypass capacitor of at least 0.1µF to GND. |
| 3 | VCC | power_out | Output of the internal LDO and supply for the gate drivers and internal circuitry; decouple with at least 1.0µF low-ESR ceramic to GND, use it for nothing else, and do not connect it to a voltage above VIN. |
| 4 | VCCUV | input | VCC undervoltage lockout set pin: 0.4V to 1.5V is multiplied by 7 to set the gate-drive UVLO, shorting to ground sets 3.5V, and leaving it open sets 7.0V. |
| 5 | FAULT | output | Open-drain fault output with about 200Ω typical pull-down that goes low when TIMER reaches the 1.3V fault threshold, warning of an impending overcurrent turn-off. |
| 6 | TIMER | bidirectional | Fault timer pin where a capacitor to GND sets the fault warning, fault turn-off and retry periods, and pulling it above 3.5V disables the timer so an overcurrent immediately pulls TGDN to TS until INP toggles low then high. |
| 7 | INP | input | CMOS-compatible input referenced to GND that sets the state of TGDN and TGUP, with an internal 1MΩ pull-down to GND. |
| 8 | OVLO | input | Overvoltage lockout input: above 1.21V pulls TGDN to TS and normal operation resumes below 1.11V; connect it to the supply through a resistor divider, or tie it to GND when unused. |
| 9 | ISET | input | Current trip threshold set pin where a resistor to GND sets the peak current threshold (voltage clamped 0.4V to 1.5V and divided by 20); shorting to GND gives a 20mV minimum ΔVTH and leaving it open gives 30mV. |
| 10 | IMON | output | Current monitor output whose voltage relative to GND equals the sense resistor voltage multiplied by 20, over a range of 0V to 1.5V. |
| 11 | TGDN | output | High-current gate driver pull-down that pulls to TS; tie it directly to the external high-side MOSFET gate for the fastest turn-off. |
| 12 | TGUP | output | High-current gate driver pull-up that pulls to BST; tie it to TGDN for maximum speed, or add a series resistor to the MOSFET gate to control turn-on in-rush current. |
| 13 | TS | passive | Top (high side) source connection of the external MOSFET, or GND in ground-referenced applications. |
| 14 | BST | power_in | High-side bootstrapped supply that needs at least 0.1µF to TS, with a voltage swing of 12V to (VIN + 12V). |
| 15 | SNS- | input | Current sense comparator input, connected to the sense resistor through a minimum 100Ω resistor; the trip threshold is clamped between 20mV and 75mV. |
| 16 | SNS+ | input | Current sense comparator input, connected to the sense resistor with a Kelvin connection; the sense resistor sits in series with the drain of the external MOSFET. |
| 17 | GND | power_in | Ground at the exposed pad, which must be soldered to the PCB for rated electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Operating Range | VIN | 3.5 | 150 | V | 4 | ||
| TS Operating Voltage Range | 0 | 135 | V | 4 | |||
| SNS+/- Input Voltage Range | 3.5 | 150 | V | Independent of VIN | 4 | ||
| VBST-TS | VBST-TS | 9 | 11 | 14 | V | VIN = VCC = VTS = 7V, IBST = 0µA | 4 |
| VBST-TS | VBST-TS | 10 | 12 | 14 | V | VIN = VCC = VTS = 10V, IBST = 0µA | 4 |
| Charge Pump Output Current | -30 | -15 | µA | VTS = 20V, VBST-TS = 10V | 4 | ||
| TG Pull-Up Resistance | 2.2 | 7 | Ω | VIN = VBST = 12V | 5 | ||
| TG Pull-Down Resistance | 1 | 4 | Ω | VIN = VBST = 12V | 5 | ||
| Input to Output Propagation Delay (rising) | tPLH | 35 | 70 | ns | VINP Rising, CL = 1nF | 5 | |
| Input to Output Propagation Delay (falling) | tPHL | 35 | 70 | ns | VINP Falling, CL = 1nF | 5 | |
| Input Threshold Voltage Rising | VIH | 1.7 | 2 | 2.2 | V | VINP Rising | 5 |
| Input Threshold Voltage Falling | VIL | 1.3 | 1.6 | 1.8 | V | VINP Falling | 5 |
| RUN and OVLO Threshold Rising | 1.16 | 1.21 | 1.26 | V | Rising | 5 | |
| RUN and OVLO Threshold Falling | 1.05 | 1.1 | 1.15 | V | Falling | 5 | |
| RUN and OVLO Leakage Current | -100 | 0 | 100 | nA | VRUN = 1.3V, VOVLO = 1.3V | 5 | |
| TIMER Threshold Voltage | 1.25 | 1.3 | 1.35 | V | VTIMER Rising to VFAULT Going Low | 5 | |
| TIMER Early Warning Voltage | 75 | 100 | 125 | mV | VFAULT Going Low to (TG-TS) Going Low | 5 | |
| TIMER Pin Fault Pull-Up Current | -115 | -100 | -80 | µA | VTIMER = 1.0V, ISET = OPEN | 5 | |
| TIMER Pin Pull-Down Current | 2 | 2.5 | 3 | µA | VTIMER = 0.6V ISET = OPEN, ΔVSNS = 0mV | 5 | |
| FAULT Output Low Voltage | 0.2 | 0.5 | V | IFAULT = 1mA | 5 | ||
| FAULT Leakage Current | -100 | 0 | 100 | nA | VFAULT = 5V | 5 | |
| Current Sense Threshold Voltage | ΔVTH | 22 | 30 | 36 | mV | ISET = OPEN or LTC7000A-1 | 5 |
| Current Sense Threshold Voltage | ΔVTH | 54 | 60 | 64 | mV | VISET = 1.2V (LTC7000A Only) | 5 |
| Current Sense Threshold Voltage | ΔVTH | 15 | 20 | 24 | mV | VISET = 0V (LTC7000A Only) | 5 |
| ISET and VCCUV Pull-Up Current | -11.3 | -10 | -8.7 | µA | VISET = 1.0V, VCCUV = 1.0V | 5 | |
| IMON Output Voltage | 1.12 | 1.2 | 1.28 | V | ΔVSNS = 60mV, VTIMER = 0V, VINP = 3.5V | 5 | |
| IMON Output Voltage | 0.52 | 0.6 | 0.68 | V | ΔVSNS = 30mV, VTIMER = 0V, VINP = 3.5V | 5 | |
| IMON Output Voltage | 0 | 0.1 | V | ΔVSNS = 0mV, VTIMER = 0V, VINP = 3.5V | 5 | ||
| Retry Duty Cycle | D | 0.06 | 0.1 | % | ΔVSNS = 200mV, CTIMER = 1nF | 5 | |
| Output Rise Time | tr | 13 | ns | 10% to 90%, CL = 1nF | 5 | ||
| Output Rise Time | tr | 90 | ns | 10% to 90%, CL = 10nF | 5 | ||
| Output Fall Time | tf | 13 | ns | 10% to 90%, CL = 1nF | 5 | ||
| Output Fall Time | tf | 40 | ns | 10% to 90%, CL = 10nF | 5 | ||
| Over-Current to TG Low Propagation Delay | 70 | ns | ΔVSNS Step 10mV to 50mV, ISET = OPEN, VTIMER = VCC, VINP = 3.5V | 5 | |||
| Abs Max VIN | VIN | -0.3 | 150 | V | 3 | ||
| Abs Max BST-TS | -0.3 | 15 | V | 3 | |||
| Abs Max VCC | VCC | -0.3 | 15 | V | 3 | ||
| Abs Max TS Voltage | -6 | 150 | V | 3 | |||
| Abs Max BST, SNS+, SNS- Voltages | -0.3 | 150 | V | 3 | |||
| Abs Max SNS+ - SNS- Continuous | -0.3 | 0.3 | V | Continuous | 3 | ||
| Abs Max SNS+ - SNS- <1ms | -100 | 100 | mA | <1ms | 3 | ||
| Abs Max INP Voltage | -6 | 15 | V | 3 | |||
| Abs Max TIMER, FAULT Voltages | -0.3 | 15 | V | 3 | |||
| Abs Max VCCUV Voltage | -0.3 | 6 | V | 3 | |||
| Abs Max RUN Voltage | -0.3 | 150 | V | LTC7000A | 3 | ||
| Abs Max ISET, IMON, OVLO Voltages | -0.3 | 6 | V | LTC7000A | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 150 | °C | LTC7000AR | 3 | |
| Storage Temperature Range | -65 | 150 | °C | 3 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | MSOP Package | 3 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 45 | °C/W | MSE package | 3 | ||
| Junction-to-Case Thermal Resistance | θJC | 10 | °C/W | MSE package | 3 | ||
| Maximum Junction Temperature | TJMAX | 150 | °C | 3 |
CAD (KiCad official)
- Symbol:
LTC7000ARMSE#TRPBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
ltc7000armse-trpbf-etched.step/ltc7000armse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc7000armse-trpbf.step/ltc7000armse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
f10784a28de2d5c3, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC7000ARMSE#TRPBF
**Analog Devices** · Gate Drive ICs · MSOP-16-EP
LTC7000ARMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RUN | input | Run control input: above 1.21V enables normal operation, below 0.7V shuts down the part (about 1µA quiescent), and it can be tied to the input supply through a resistive divider to set the undervoltage lockout. |
| 2 | VIN | power_in | Main supply pin, which needs a bypass capacitor of at least 0.1µF to GND. |
| 3 | VCC | power_out | Output of the internal LDO and supply for the gate drivers and internal circuitry; decouple with at least 1.0µF low-ESR ceramic to GND, use it for nothing else, and do not connect it to a voltage above VIN. |
| 4 | VCCUV | input | VCC undervoltage lockout set pin: 0.4V to 1.5V is multiplied by 7 to set the gate-drive UVLO, shorting to ground sets 3.5V, and leaving it open sets 7.0V. |
| 5 | FAULT | output | Open-drain fault output with about 200Ω typical pull-down that goes low when TIMER reaches the 1.3V fault threshold, warning of an impending overcurrent turn-off. |
| 6 | TIMER | bidirectional | Fault timer pin where a capacitor to GND sets the fault warning, fault turn-off and retry periods, and pulling it above 3.5V disables the timer so an overcurrent immediately pulls TGDN to TS until INP toggles low then high. |
| 7 | INP | input | CMOS-compatible input referenced to GND that sets the state of TGDN and TGUP, with an internal 1MΩ pull-down to GND. |
| 8 | OVLO | input | Overvoltage lockout input: above 1.21V pulls TGDN to TS and normal operation resumes below 1.11V; connect it to the supply through a resistor divider, or tie it to GND when unused. |
| 9 | ISET | input | Current trip threshold set pin where a resistor to GND sets the peak current threshold (voltage clamped 0.4V to 1.5V and divided by 20); shorting to GND gives a 20mV minimum ΔVTH and leaving it open gives 30mV. |
| 10 | IMON | output | Current monitor output whose voltage relative to GND equals the sense resistor voltage multiplied by 20, over a range of 0V to 1.5V. |
| 11 | TGDN | output | High-current gate driver pull-down that pulls to TS; tie it directly to the external high-side MOSFET gate for the fastest turn-off. |
| 12 | TGUP | output | High-current gate driver pull-up that pulls to BST; tie it to TGDN for maximum speed, or add a series resistor to the MOSFET gate to control turn-on in-rush current. |
| 13 | TS | passive | Top (high side) source connection of the external MOSFET, or GND in ground-referenced applications. |
| 14 | BST | power_in | High-side bootstrapped supply that needs at least 0.1µF to TS, with a voltage swing of 12V to (VIN + 12V). |
| 15 | SNS- | input | Current sense comparator input, connected to the sense resistor through a minimum 100Ω resistor; the trip threshold is clamped between 20mV and 75mV. |
| 16 | SNS+ | input | Current sense comparator input, connected to the sense resistor with a Kelvin connection; the sense resistor sits in series with the drain of the external MOSFET. |
| 17 | GND | power_in | Ground at the exposed pad, which must be soldered to the PCB for rated electrical and thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Operating Range | VIN | 3.5 | | 150 | V | | 4 |
| TS Operating Voltage Range | | 0 | | 135 | V | | 4 |
| SNS+/- Input Voltage Range | | 3.5 | | 150 | V | Independent of VIN | 4 |
| VBST-TS | VBST-TS | 9 | 11 | 14 | V | VIN = VCC = VTS = 7V, IBST = 0µA | 4 |
| VBST-TS | VBST-TS | 10 | 12 | 14 | V | VIN = VCC = VTS = 10V, IBST = 0µA | 4 |
| Charge Pump Output Current | | -30 | -15 | | µA | VTS = 20V, VBST-TS = 10V | 4 |
| TG Pull-Up Resistance | | | 2.2 | 7 | Ω | VIN = VBST = 12V | 5 |
| TG Pull-Down Resistance | | | 1 | 4 | Ω | VIN = VBST = 12V | 5 |
| Input to Output Propagation Delay (rising) | tPLH | | 35 | 70 | ns | VINP Rising, CL = 1nF | 5 |
| Input to Output Propagation Delay (falling) | tPHL | | 35 | 70 | ns | VINP Falling, CL = 1nF | 5 |
| Input Threshold Voltage Rising | VIH | 1.7 | 2 | 2.2 | V | VINP Rising | 5 |
| Input Threshold Voltage Falling | VIL | 1.3 | 1.6 | 1.8 | V | VINP Falling | 5 |
| RUN and OVLO Threshold Rising | | 1.16 | 1.21 | 1.26 | V | Rising | 5 |
| RUN and OVLO Threshold Falling | | 1.05 | 1.1 | 1.15 | V | Falling | 5 |
| RUN and OVLO Leakage Current | | -100 | 0 | 100 | nA | VRUN = 1.3V, VOVLO = 1.3V | 5 |
| TIMER Threshold Voltage | | 1.25 | 1.3 | 1.35 | V | VTIMER Rising to VFAULT Going Low | 5 |
| TIMER Early Warning Voltage | | 75 | 100 | 125 | mV | VFAULT Going Low to (TG-TS) Going Low | 5 |
| TIMER Pin Fault Pull-Up Current | | -115 | -100 | -80 | µA | VTIMER = 1.0V, ISET = OPEN | 5 |
| TIMER Pin Pull-Down Current | | 2 | 2.5 | 3 | µA | VTIMER = 0.6V ISET = OPEN, ΔVSNS = 0mV | 5 |
| FAULT Output Low Voltage | | | 0.2 | 0.5 | V | IFAULT = 1mA | 5 |
| FAULT Leakage Current | | -100 | 0 | 100 | nA | VFAULT = 5V | 5 |
| Current Sense Threshold Voltage | ΔVTH | 22 | 30 | 36 | mV | ISET = OPEN or LTC7000A-1 | 5 |
| Current Sense Threshold Voltage | ΔVTH | 54 | 60 | 64 | mV | VISET = 1.2V (LTC7000A Only) | 5 |
| Current Sense Threshold Voltage | ΔVTH | 15 | 20 | 24 | mV | VISET = 0V (LTC7000A Only) | 5 |
| ISET and VCCUV Pull-Up Current | | -11.3 | -10 | -8.7 | µA | VISET = 1.0V, VCCUV = 1.0V | 5 |
| IMON Output Voltage | | 1.12 | 1.2 | 1.28 | V | ΔVSNS = 60mV, VTIMER = 0V, VINP = 3.5V | 5 |
| IMON Output Voltage | | 0.52 | 0.6 | 0.68 | V | ΔVSNS = 30mV, VTIMER = 0V, VINP = 3.5V | 5 |
| IMON Output Voltage | | | 0 | 0.1 | V | ΔVSNS = 0mV, VTIMER = 0V, VINP = 3.5V | 5 |
| Retry Duty Cycle | D | | 0.06 | 0.1 | % | ΔVSNS = 200mV, CTIMER = 1nF | 5 |
| Output Rise Time | tr | | 13 | | ns | 10% to 90%, CL = 1nF | 5 |
| Output Rise Time | tr | | 90 | | ns | 10% to 90%, CL = 10nF | 5 |
| Output Fall Time | tf | | 13 | | ns | 10% to 90%, CL = 1nF | 5 |
| Output Fall Time | tf | | 40 | | ns | 10% to 90%, CL = 10nF | 5 |
| Over-Current to TG Low Propagation Delay | | | 70 | | ns | ΔVSNS Step 10mV to 50mV, ISET = OPEN, VTIMER = VCC, VINP = 3.5V | 5 |
| Abs Max VIN | VIN | -0.3 | | 150 | V | | 3 |
| Abs Max BST-TS | | -0.3 | | 15 | V | | 3 |
| Abs Max VCC | VCC | -0.3 | | 15 | V | | 3 |
| Abs Max TS Voltage | | -6 | | 150 | V | | 3 |
| Abs Max BST, SNS+, SNS- Voltages | | -0.3 | | 150 | V | | 3 |
| Abs Max SNS+ - SNS- Continuous | | -0.3 | | 0.3 | V | Continuous | 3 |
| Abs Max SNS+ - SNS- <1ms | | -100 | | 100 | mA | <1ms | 3 |
| Abs Max INP Voltage | | -6 | | 15 | V | | 3 |
| Abs Max TIMER, FAULT Voltages | | -0.3 | | 15 | V | | 3 |
| Abs Max VCCUV Voltage | | -0.3 | | 6 | V | | 3 |
| Abs Max RUN Voltage | | -0.3 | | 150 | V | LTC7000A | 3 |
| Abs Max ISET, IMON, OVLO Voltages | | -0.3 | | 6 | V | LTC7000A | 3 |
| Operating Junction Temperature Range | TJ | -40 | | 150 | °C | LTC7000AR | 3 |
| Storage Temperature Range | | -65 | | 150 | °C | | 3 |
| Lead Temperature (Soldering, 10 sec) | | | | 300 | °C | MSOP Package | 3 |
| Junction-to-Ambient Thermal Resistance | θJA | | 45 | | °C/W | MSE package | 3 |
| Junction-to-Case Thermal Resistance | θJC | | 10 | | °C/W | MSE package | 3 |
| Maximum Junction Temperature | TJMAX | | | 150 | °C | | 3 |
## CAD (KiCad official)
- Symbol: `LTC7000ARMSE#TRPBF`
- Footprint: `Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm`
- 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `ltc7000armse-trpbf-etched.step` / `ltc7000armse-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc7000armse-trpbf.step` / `ltc7000armse-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/ltc7000a.pdf) (30 pp, sha256 `f10784a28de2d5c3`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc7000armse-trpbf-datasheet.pdf)