main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ltc7000armse-trpbf: viewers · Ray
ltc7000armse-trpbf-etched.glb Publish 0.1.0 · Ray
ltc7000armse-trpbf-etched.step ltc7000armse-trpbf: factory component page (tier=mfr) · Ray
ltc7000armse-trpbf-hero.glb ltc7000armse-trpbf: hero GLB from the etched model (keeps the MPN mark) · Ray
ltc7000armse-trpbf-hero.overlay.json Publish 0.1.0 · Ray
ltc7000armse-trpbf.glb Publish 0.1.0 · Ray
ltc7000armse-trpbf.kicad_mod Publish 0.1.0 · Ray
ltc7000armse-trpbf.kicad_sym Publish 0.1.0 · Ray
ltc7000armse-trpbf.lbr Publish 0.1.0 · Ray
ltc7000armse-trpbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 17 pins · Ray

LTC7000ARMSE#TRPBF

Analog Devices · Gate Drive ICs · MSOP-16-EP

LTC7000ARMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RUN input Run control input: above 1.21V enables normal operation, below 0.7V shuts down the part (about 1µA quiescent), and it can be tied to the input supply through a resistive divider to set the undervoltage lockout.
2 VIN power_in Main supply pin, which needs a bypass capacitor of at least 0.1µF to GND.
3 VCC power_out Output of the internal LDO and supply for the gate drivers and internal circuitry; decouple with at least 1.0µF low-ESR ceramic to GND, use it for nothing else, and do not connect it to a voltage above VIN.
4 VCCUV input VCC undervoltage lockout set pin: 0.4V to 1.5V is multiplied by 7 to set the gate-drive UVLO, shorting to ground sets 3.5V, and leaving it open sets 7.0V.
5 FAULT output Open-drain fault output with about 200Ω typical pull-down that goes low when TIMER reaches the 1.3V fault threshold, warning of an impending overcurrent turn-off.
6 TIMER bidirectional Fault timer pin where a capacitor to GND sets the fault warning, fault turn-off and retry periods, and pulling it above 3.5V disables the timer so an overcurrent immediately pulls TGDN to TS until INP toggles low then high.
7 INP input CMOS-compatible input referenced to GND that sets the state of TGDN and TGUP, with an internal 1MΩ pull-down to GND.
8 OVLO input Overvoltage lockout input: above 1.21V pulls TGDN to TS and normal operation resumes below 1.11V; connect it to the supply through a resistor divider, or tie it to GND when unused.
9 ISET input Current trip threshold set pin where a resistor to GND sets the peak current threshold (voltage clamped 0.4V to 1.5V and divided by 20); shorting to GND gives a 20mV minimum ΔVTH and leaving it open gives 30mV.
10 IMON output Current monitor output whose voltage relative to GND equals the sense resistor voltage multiplied by 20, over a range of 0V to 1.5V.
11 TGDN output High-current gate driver pull-down that pulls to TS; tie it directly to the external high-side MOSFET gate for the fastest turn-off.
12 TGUP output High-current gate driver pull-up that pulls to BST; tie it to TGDN for maximum speed, or add a series resistor to the MOSFET gate to control turn-on in-rush current.
13 TS passive Top (high side) source connection of the external MOSFET, or GND in ground-referenced applications.
14 BST power_in High-side bootstrapped supply that needs at least 0.1µF to TS, with a voltage swing of 12V to (VIN + 12V).
15 SNS- input Current sense comparator input, connected to the sense resistor through a minimum 100Ω resistor; the trip threshold is clamped between 20mV and 75mV.
16 SNS+ input Current sense comparator input, connected to the sense resistor with a Kelvin connection; the sense resistor sits in series with the drain of the external MOSFET.
17 GND power_in Ground at the exposed pad, which must be soldered to the PCB for rated electrical and thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Operating Range VIN 3.5 150 V 4
TS Operating Voltage Range 0 135 V 4
SNS+/- Input Voltage Range 3.5 150 V Independent of VIN 4
VBST-TS VBST-TS 9 11 14 V VIN = VCC = VTS = 7V, IBST = 0µA 4
VBST-TS VBST-TS 10 12 14 V VIN = VCC = VTS = 10V, IBST = 0µA 4
Charge Pump Output Current -30 -15 µA VTS = 20V, VBST-TS = 10V 4
TG Pull-Up Resistance 2.2 7 Ω VIN = VBST = 12V 5
TG Pull-Down Resistance 1 4 Ω VIN = VBST = 12V 5
Input to Output Propagation Delay (rising) tPLH 35 70 ns VINP Rising, CL = 1nF 5
Input to Output Propagation Delay (falling) tPHL 35 70 ns VINP Falling, CL = 1nF 5
Input Threshold Voltage Rising VIH 1.7 2 2.2 V VINP Rising 5
Input Threshold Voltage Falling VIL 1.3 1.6 1.8 V VINP Falling 5
RUN and OVLO Threshold Rising 1.16 1.21 1.26 V Rising 5
RUN and OVLO Threshold Falling 1.05 1.1 1.15 V Falling 5
RUN and OVLO Leakage Current -100 0 100 nA VRUN = 1.3V, VOVLO = 1.3V 5
TIMER Threshold Voltage 1.25 1.3 1.35 V VTIMER Rising to VFAULT Going Low 5
TIMER Early Warning Voltage 75 100 125 mV VFAULT Going Low to (TG-TS) Going Low 5
TIMER Pin Fault Pull-Up Current -115 -100 -80 µA VTIMER = 1.0V, ISET = OPEN 5
TIMER Pin Pull-Down Current 2 2.5 3 µA VTIMER = 0.6V ISET = OPEN, ΔVSNS = 0mV 5
FAULT Output Low Voltage 0.2 0.5 V IFAULT = 1mA 5
FAULT Leakage Current -100 0 100 nA VFAULT = 5V 5
Current Sense Threshold Voltage ΔVTH 22 30 36 mV ISET = OPEN or LTC7000A-1 5
Current Sense Threshold Voltage ΔVTH 54 60 64 mV VISET = 1.2V (LTC7000A Only) 5
Current Sense Threshold Voltage ΔVTH 15 20 24 mV VISET = 0V (LTC7000A Only) 5
ISET and VCCUV Pull-Up Current -11.3 -10 -8.7 µA VISET = 1.0V, VCCUV = 1.0V 5
IMON Output Voltage 1.12 1.2 1.28 V ΔVSNS = 60mV, VTIMER = 0V, VINP = 3.5V 5
IMON Output Voltage 0.52 0.6 0.68 V ΔVSNS = 30mV, VTIMER = 0V, VINP = 3.5V 5
IMON Output Voltage 0 0.1 V ΔVSNS = 0mV, VTIMER = 0V, VINP = 3.5V 5
Retry Duty Cycle D 0.06 0.1 % ΔVSNS = 200mV, CTIMER = 1nF 5
Output Rise Time tr 13 ns 10% to 90%, CL = 1nF 5
Output Rise Time tr 90 ns 10% to 90%, CL = 10nF 5
Output Fall Time tf 13 ns 10% to 90%, CL = 1nF 5
Output Fall Time tf 40 ns 10% to 90%, CL = 10nF 5
Over-Current to TG Low Propagation Delay 70 ns ΔVSNS Step 10mV to 50mV, ISET = OPEN, VTIMER = VCC, VINP = 3.5V 5
Abs Max VIN VIN -0.3 150 V 3
Abs Max BST-TS -0.3 15 V 3
Abs Max VCC VCC -0.3 15 V 3
Abs Max TS Voltage -6 150 V 3
Abs Max BST, SNS+, SNS- Voltages -0.3 150 V 3
Abs Max SNS+ - SNS- Continuous -0.3 0.3 V Continuous 3
Abs Max SNS+ - SNS- <1ms -100 100 mA <1ms 3
Abs Max INP Voltage -6 15 V 3
Abs Max TIMER, FAULT Voltages -0.3 15 V 3
Abs Max VCCUV Voltage -0.3 6 V 3
Abs Max RUN Voltage -0.3 150 V LTC7000A 3
Abs Max ISET, IMON, OVLO Voltages -0.3 6 V LTC7000A 3
Operating Junction Temperature Range TJ -40 150 °C LTC7000AR 3
Storage Temperature Range -65 150 °C 3
Lead Temperature (Soldering, 10 sec) 300 °C MSOP Package 3
Junction-to-Ambient Thermal Resistance θJA 45 °C/W MSE package 3
Junction-to-Case Thermal Resistance θJC 10 °C/W MSE package 3
Maximum Junction Temperature TJMAX 150 °C 3

CAD (KiCad official)

  • Symbol: LTC7000ARMSE#TRPBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: ltc7000armse-trpbf-etched.step / ltc7000armse-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc7000armse-trpbf.step / ltc7000armse-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 f10784a28de2d5c3, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF