main
Ray
Publish 0.1.0
a4f612b
LTC6902IMS#TRPBF
Analog Devices · Timers / Clock Oscillators · MSOP-10
LTC6902IMS#TRPBF from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Positive supply pin, operating from 2.7V to 5.5V with absolute maximum supply of 6V to GND. |
| 2 | DIV | input | Programmable divider select: tie to GND for N=1, leave open for N=10, or tie to V+ for N=100, with logic high at V+ minus 0.4V minimum and logic low at 0.4V maximum. |
| 3 | PH | input | Multiphase mode select: tie to 0V for 2-phase, leave open for 3-phase, or tie to V+ for 4-phase, with logic high at V+ minus 0.4V minimum and logic low at 0.4V maximum. |
| 4 | OUT1 | output | CMOS clock output 1 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 5 | OUT2 | output | CMOS clock output 2 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 6 | OUT3 | output | CMOS clock output 3 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 7 | OUT4 | output | CMOS clock output 4 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 8 | GND | power_in | Ground reference pin for the device and the reference for all pin voltages. |
| 9 | MOD | input | Spread spectrum modulation control: a resistor RMOD to V+ sets the spreading percentage, and grounding this pin disables SSFM, which is the best method of disabling it. |
| 10 | SET | input | Oscillator frequency-setting pin: a resistor RSET connected from this pin to V+ sets the master oscillator frequency. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10 |
| Category | Clock and Timing |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Frequency Accuracy | ∆fOUT | -1.5 | 0.5 | 1.5 | % | V+ = 5V; 5kHz ≤ fOUT ≤ 10MHz | 2 |
| Frequency Accuracy | ∆fOUT | -2 | 2 | % | 1kHz ≤ fOUT ≤ 5kHz | 2 | |
| Frequency Accuracy | ∆fOUT | -4 | 3 | 4 | % | 10MHz ≤ fOUT ≤ 20MHz | 2 |
| Frequency Accuracy (LTC6902I) | ∆fOUT | -2.5 | 2.5 | % | 5kHz < fOUT ≤ 10MHz, LTC6902I | 2 | |
| RSET Frequency Setting Resistor Range | RSET | 20 | 400 | kΩ | ∆fOUT < 1.5%, V+ = 5V | 2 | |
| Frequency Drift Over Temperature | ∆fOUT/∆T | -0.004 | 0.004 | %/°C | RSET = 63.2k | 2 | |
| Frequency Drift Over Supply | ∆fOUT/∆V | 0.04 | 0.12 | %/V | V+ = 2.7V to 5V, RSET = 63.2k | 2 | |
| Duty Cycle | 49 | 50 | 51 | % | Pin 2 = V+ or Open (N = 100 or 10); Pin 3 = 0V (2-Phase, M = 1) | 2 | |
| Duty Cycle | 32.3 | 33.3 | 34.3 | % | Pin 2 = V+ or Open (N = 100 or 10); Pin 3 = Open (3-Phase, M = 3) | 2 | |
| Duty Cycle | 45 | 50 | 55 | % | Pin 2 = 0V (N = 1); Pin 3 = 0V (2-Phase, M = 1) | 2 | |
| Supply Voltage (V+) Operating Range | V+ | 2.7 | 5.5 | V | 3 | ||
| Power Supply Current | IS | 0.35 | 0.55 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), fOUT = 5kHz; V+ = 5V | 3 | |
| Power Supply Current | IS | 0.32 | 0.5 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), fOUT = 5kHz; V+ = 2.7V | 3 | |
| Power Supply Current | IS | 2.35 | 3.5 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), fOUT = 10MHz; V+ = 5V | 3 | |
| Power Supply Current | IS | 1.4 | 1.8 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), fOUT = 10MHz; V+ = 2.7V | 3 | |
| Power Supply Current | IS | 0.45 | 0.63 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), RMOD = 800k; V+ = 5V | 3 | |
| Power Supply Current | IS | 0.34 | 0.5 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), RMOD = 800k; V+ = 2.7V | 3 | |
| Power Supply Current | IS | 2.5 | 3.6 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), RMOD = 40k; V+ = 5V | 3 | |
| Power Supply Current | IS | 1.4 | 1.9 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), RMOD = 40k; V+ = 2.7V | 3 | |
| Low Level DIV Input Voltage | VIL_DIV | 0.4 | V | 3 | |||
| Low Level PH Input Voltage | VIL_PH | 0.4 | V | 3 | |||
| DIV Input Current | IDIV | 2 | 4 | µA | Pin 2 = V+, V+ = 5V | 3 | |
| DIV Input Current | IDIV | -4 | -2 | µA | Pin 2 = 0V, V+ = 5V | 3 | |
| PH Input Current | IPH | 2 | 4 | µA | Pin 3 = V+, V+ = 5V | 3 | |
| PH Input Current | IPH | -4 | -2 | µA | Pin 3 = 0V, V+ = 5V | 3 | |
| High Level Output Voltage | VOH | 4.75 | 4.9 | V | V+ = 5V, IOH = -1mA | 3 | |
| High Level Output Voltage | VOH | 4.4 | 4.7 | V | V+ = 5V, IOH = -4mA | 3 | |
| High Level Output Voltage | VOH | 2.35 | 2.6 | V | V+ = 2.7V, IOH = -1mA | 3 | |
| High Level Output Voltage | VOH | 1.85 | 2.2 | V | V+ = 2.7V, IOH = -4mA | 3 | |
| Low Level Output Voltage | VOL | 0.05 | 0.15 | V | V+ = 5V, IOL = 1mA | 3 | |
| Low Level Output Voltage | VOL | 0.2 | 0.4 | V | V+ = 5V, IOL = 4mA | 3 | |
| Low Level Output Voltage | VOL | 0.1 | 0.3 | V | V+ = 2.7V, IOL = 1mA | 3 | |
| Low Level Output Voltage | VOL | 0.4 | 0.7 | V | V+ = 2.7V, IOL = 4mA | 3 | |
| Spread Spectrum Frequency Modulation Spreading Percentage | 35 | 40 | 45 | % | V+ = 5V, N = 10, RSET = 20k, RMOD = 10k | 3 | |
| Spread Spectrum Frequency Modulation Spreading Percentage | 7.5 | 10 | 12.5 | % | V+ = 5V, N = 10, RSET = 20k, RMOD = 40k | 3 | |
| Supply Voltage (V+) to GND | V+ | -0.3 | 6 | V | Referred to GND | 2 | |
| Operating Temperature Range (LTC6902I) | -40 | 85 | °C | LTC6902I | 2 | ||
| Specified Temperature Range (LTC6902I) | -40 | 85 | °C | LTC6902I | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering) | 300 | °C | Soldering, 10 sec | 2 | |||
| Maximum Junction Temperature | TJMAX | 150 | °C | 2 | |||
| Thermal Resistance, Junction to Ambient | θJA | 250 | °C/W | 2 | |||
| Rise Time | tr | 14 | ns | V+ = 5V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 | ||
| Rise Time | tr | 7 | ns | V+ = 5V; Pin 2 = 0V (N = 1) | 3 | ||
| Rise Time | tr | 19 | ns | V+ = 2.7V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 | ||
| Rise Time | tr | 11 | ns | V+ = 2.7V; Pin 2 = 0V (N = 1) | 3 | ||
| Fall Time | tf | 13 | ns | V+ = 5V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 | ||
| Fall Time | tf | 6 | ns | V+ = 5V; Pin 2 = 0V (N = 1) | 3 | ||
| Fall Time | tf | 19 | ns | V+ = 2.7V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 | ||
| Fall Time | tf | 10 | ns | V+ = 2.7V; Pin 2 = 0V (N = 1) | 3 |
CAD (KiCad official)
- Symbol:
LTC6902IMS#TRPBF - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
ltc6902ims-trpbf-etched.step/ltc6902ims-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6902ims-trpbf.step/ltc6902ims-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
e4b39fe7ae1e50d9, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC6902IMS#TRPBF
**Analog Devices** · Timers / Clock Oscillators · MSOP-10
LTC6902IMS#TRPBF from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Positive supply pin, operating from 2.7V to 5.5V with absolute maximum supply of 6V to GND. |
| 2 | DIV | input | Programmable divider select: tie to GND for N=1, leave open for N=10, or tie to V+ for N=100, with logic high at V+ minus 0.4V minimum and logic low at 0.4V maximum. |
| 3 | PH | input | Multiphase mode select: tie to 0V for 2-phase, leave open for 3-phase, or tie to V+ for 4-phase, with logic high at V+ minus 0.4V minimum and logic low at 0.4V maximum. |
| 4 | OUT1 | output | CMOS clock output 1 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 5 | OUT2 | output | CMOS clock output 2 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 6 | OUT3 | output | CMOS clock output 3 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 7 | OUT4 | output | CMOS clock output 4 with ON resistance typically less than 100Ω, suitable for driving general logic and switching regulator clock inputs. |
| 8 | GND | power_in | Ground reference pin for the device and the reference for all pin voltages. |
| 9 | MOD | input | Spread spectrum modulation control: a resistor RMOD to V+ sets the spreading percentage, and grounding this pin disables SSFM, which is the best method of disabling it. |
| 10 | SET | input | Oscillator frequency-setting pin: a resistor RSET connected from this pin to V+ sets the master oscillator frequency. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10 |
| Category | Clock and Timing |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Frequency Accuracy | ∆fOUT | -1.5 | 0.5 | 1.5 | % | V+ = 5V; 5kHz ≤ fOUT ≤ 10MHz | 2 |
| Frequency Accuracy | ∆fOUT | -2 | | 2 | % | 1kHz ≤ fOUT ≤ 5kHz | 2 |
| Frequency Accuracy | ∆fOUT | -4 | 3 | 4 | % | 10MHz ≤ fOUT ≤ 20MHz | 2 |
| Frequency Accuracy (LTC6902I) | ∆fOUT | -2.5 | | 2.5 | % | 5kHz < fOUT ≤ 10MHz, LTC6902I | 2 |
| RSET Frequency Setting Resistor Range | RSET | 20 | | 400 | kΩ | ∆fOUT < 1.5%, V+ = 5V | 2 |
| Frequency Drift Over Temperature | ∆fOUT/∆T | -0.004 | | 0.004 | %/°C | RSET = 63.2k | 2 |
| Frequency Drift Over Supply | ∆fOUT/∆V | | 0.04 | 0.12 | %/V | V+ = 2.7V to 5V, RSET = 63.2k | 2 |
| Duty Cycle | | 49 | 50 | 51 | % | Pin 2 = V+ or Open (N = 100 or 10); Pin 3 = 0V (2-Phase, M = 1) | 2 |
| Duty Cycle | | 32.3 | 33.3 | 34.3 | % | Pin 2 = V+ or Open (N = 100 or 10); Pin 3 = Open (3-Phase, M = 3) | 2 |
| Duty Cycle | | 45 | 50 | 55 | % | Pin 2 = 0V (N = 1); Pin 3 = 0V (2-Phase, M = 1) | 2 |
| Supply Voltage (V+) Operating Range | V+ | 2.7 | | 5.5 | V | | 3 |
| Power Supply Current | IS | | 0.35 | 0.55 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), fOUT = 5kHz; V+ = 5V | 3 |
| Power Supply Current | IS | | 0.32 | 0.5 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), fOUT = 5kHz; V+ = 2.7V | 3 |
| Power Supply Current | IS | | 2.35 | 3.5 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), fOUT = 10MHz; V+ = 5V | 3 |
| Power Supply Current | IS | | 1.4 | 1.8 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), fOUT = 10MHz; V+ = 2.7V | 3 |
| Power Supply Current | IS | | 0.45 | 0.63 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), RMOD = 800k; V+ = 5V | 3 |
| Power Supply Current | IS | | 0.34 | 0.5 | mA | RSET = 400k, RL = ∞, Pin 2 = V+ (N = 100), RMOD = 800k; V+ = 2.7V | 3 |
| Power Supply Current | IS | | 2.5 | 3.6 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), RMOD = 40k; V+ = 5V | 3 |
| Power Supply Current | IS | | 1.4 | 1.9 | mA | RSET = 20k, RL = ∞, Pin 2 = 0V (N = 1), RMOD = 40k; V+ = 2.7V | 3 |
| Low Level DIV Input Voltage | VIL_DIV | | | 0.4 | V | | 3 |
| Low Level PH Input Voltage | VIL_PH | | | 0.4 | V | | 3 |
| DIV Input Current | IDIV | 2 | | 4 | µA | Pin 2 = V+, V+ = 5V | 3 |
| DIV Input Current | IDIV | -4 | | -2 | µA | Pin 2 = 0V, V+ = 5V | 3 |
| PH Input Current | IPH | 2 | | 4 | µA | Pin 3 = V+, V+ = 5V | 3 |
| PH Input Current | IPH | -4 | | -2 | µA | Pin 3 = 0V, V+ = 5V | 3 |
| High Level Output Voltage | VOH | 4.75 | 4.9 | | V | V+ = 5V, IOH = -1mA | 3 |
| High Level Output Voltage | VOH | 4.4 | 4.7 | | V | V+ = 5V, IOH = -4mA | 3 |
| High Level Output Voltage | VOH | 2.35 | 2.6 | | V | V+ = 2.7V, IOH = -1mA | 3 |
| High Level Output Voltage | VOH | 1.85 | 2.2 | | V | V+ = 2.7V, IOH = -4mA | 3 |
| Low Level Output Voltage | VOL | | 0.05 | 0.15 | V | V+ = 5V, IOL = 1mA | 3 |
| Low Level Output Voltage | VOL | | 0.2 | 0.4 | V | V+ = 5V, IOL = 4mA | 3 |
| Low Level Output Voltage | VOL | | 0.1 | 0.3 | V | V+ = 2.7V, IOL = 1mA | 3 |
| Low Level Output Voltage | VOL | | 0.4 | 0.7 | V | V+ = 2.7V, IOL = 4mA | 3 |
| Spread Spectrum Frequency Modulation Spreading Percentage | | 35 | 40 | 45 | % | V+ = 5V, N = 10, RSET = 20k, RMOD = 10k | 3 |
| Spread Spectrum Frequency Modulation Spreading Percentage | | 7.5 | 10 | 12.5 | % | V+ = 5V, N = 10, RSET = 20k, RMOD = 40k | 3 |
| Supply Voltage (V+) to GND | V+ | -0.3 | | 6 | V | Referred to GND | 2 |
| Operating Temperature Range (LTC6902I) | | -40 | | 85 | °C | LTC6902I | 2 |
| Specified Temperature Range (LTC6902I) | | -40 | | 85 | °C | LTC6902I | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Lead Temperature (Soldering) | | | | 300 | °C | Soldering, 10 sec | 2 |
| Maximum Junction Temperature | TJMAX | | | 150 | °C | | 2 |
| Thermal Resistance, Junction to Ambient | θJA | | 250 | | °C/W | | 2 |
| Rise Time | tr | | 14 | | ns | V+ = 5V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 |
| Rise Time | tr | | 7 | | ns | V+ = 5V; Pin 2 = 0V (N = 1) | 3 |
| Rise Time | tr | | 19 | | ns | V+ = 2.7V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 |
| Rise Time | tr | | 11 | | ns | V+ = 2.7V; Pin 2 = 0V (N = 1) | 3 |
| Fall Time | tf | | 13 | | ns | V+ = 5V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 |
| Fall Time | tf | | 6 | | ns | V+ = 5V; Pin 2 = 0V (N = 1) | 3 |
| Fall Time | tf | | 19 | | ns | V+ = 2.7V; Pin 2 = V+ or Open (N = 100 or N = 10) | 3 |
| Fall Time | tf | | 10 | | ns | V+ = 2.7V; Pin 2 = 0V (N = 1) | 3 |
## CAD (KiCad official)
- Symbol: `LTC6902IMS#TRPBF`
- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`
- 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files: `ltc6902ims-trpbf-etched.step` / `ltc6902ims-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc6902ims-trpbf.step` / `ltc6902ims-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/6902f.pdf) (16 pp, sha256 `e4b39fe7ae1e50d9`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc6902ims-trpbf-datasheet.pdf)