Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LTC4415EDHC#PBF
Analog Devices · Switching Diodes · DFN-16(3x5)
LTC4415EDHC#PBF from Analog Devices, in a DFN-16(3x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | power_in | Diode 1 anode and positive supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 2, and may be grounded when unused. |
| 2 | IN1 | power_in | Diode 1 anode and positive supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 1, and may be grounded when unused. |
| 3 | EN1 | input | Enable input for Diode 1; a high signal greater than VENTH enables Diode 1, with VENTH typically 800mV. |
| 4 | CLIM1 | passive | Current limit adjust and monitor for Diode 1; a resistor to ground sets the limit (RCLIM allowed 125Ω to 1000Ω), a fixed 6A limit applies when shorted to ground, and the pin must not be left open. |
| 5 | CLIM2 | passive | Current limit adjust and monitor for Diode 2; a resistor to ground sets the limit (RCLIM allowed 125Ω to 1000Ω), a fixed 6A limit applies when shorted to ground, and the pin must not be left open. |
| 6 | EN2 | input | Enable input for Diode 2; a low signal less than VENTH enables Diode 2, with VENTH typically 800mV. |
| 7 | IN2 | power_in | Diode 2 anode and positive supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 8, and may be grounded when unused. |
| 8 | IN2 | power_in | Diode 2 anode and positive supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 7, and may be grounded when unused. |
| 9 | OUT2 | power_out | Diode 2 cathode and output; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 10, and left open when unused. |
| 10 | OUT2 | power_out | Diode 2 cathode and output; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 9, and left open when unused. |
| 11 | STAT2 | output | Open-drain status output that pulls down during Diode 2 forward conduction; may be left open or grounded when unused. |
| 12 | WARN2 | output | Open-drain overcurrent and thermal warning output for Diode 2 that pulls low when its current exceeds the current limit or die temperature nears thermal shutdown (160°C typical threshold). |
| 13 | WARN1 | output | Open-drain overcurrent and thermal warning output for Diode 1 that pulls low when its current exceeds the current limit or die temperature nears thermal shutdown (160°C typical threshold). |
| 14 | STAT1 | output | Open-drain status output that pulls down during Diode 1 forward conduction; may be left open or grounded when unused. |
| 15 | OUT1 | power_out | Diode 1 cathode and output; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 16, and left open when unused. |
| 16 | OUT1 | power_out | Diode 1 cathode and output; bypass with a ceramic capacitor of at least 4.7µF, fused to pin 15, and left open when unused. |
| 17 | GND | power_in | Exposed pad is device ground and must be soldered to PCB ground for both electrical connection and thermal conductivity. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-16(3x5) |
| Category | Diodes |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Range | VIN1, VOUT1, VIN2, VOUT2 | 1.7 | 5.5 | V | At Least One Input/Output Must Be in This Range | 3 | |
| Undervoltage Lockout VINx Rising | VUVLO | 1.63 | 1.7 | V | VINx Rising | 3 | |
| Quiescent Current In Forward Regulation | IQF | 44 | 80 | µA | VIN1 = VEN1 = VEN2 = 3.6V, IOUT1 = -1mA, VIN2 = VOUT2 = 0V, Measured Through GND Pin | 3 | |
| Quiescent Current In Shutdown | IQOFF | 13 | 28 | µA | VIN1 = VIN2 = VEN2 = 3.6V, VEN1 = 0V, VOUT1 = VOUT2 = 0V, Measured Through GND Pin | 3 | |
| Reverse Turn-Off Current: OUT1 OUT2 | IQR(OUT) | 18 | 40 | µA | VIN1 = 3.6V, VOUT1 = 3.7V, VIN2 = 3.5V, VOUT2 = 3.6V (VOUT1 > VOUT2) | 3 | |
| Reverse Turn-Off Current: OUT1 OUT2 (second row) | IQR(OUT) | 5 | 11 | µA | 3 | ||
| INx Pin Current In Reverse Turn-Off | IQR(IN) | 4 | 10 | µA | VOUT1 = VOUT2 = 5.5V | 3 | |
| INx Pin Leakage Current | ILEAK(IN) | -1 | 1 | µA | VIN1 = VIN2 = 0V, VOUT1 = VOUT2 = 5.5V | 3 | |
| Forward Regulation Voltage (VINx, VOUTx) | VFR | 5 | 15 | 25 | mV | IOUTx = -1mA | 3 |
| Reverse Turn-Off Voltage (VINx, VOUTx) | VRTO | -50 | -30 | -10 | mV | 3 | |
| Forward Dynamic Resistance in Regulation | RFR | 18 | 30 | mΩ | IOUTx = -100mA to -300mA | 3 | |
| On-Resistance in Constant Resistance Mode | RON | 50 | 70 | mΩ | IOUTx = -1A | 3 | |
| Current Monitor Ratio | ICLIMx /IOUTx | 0.9 | 1 | 1.1 | mA/A | When IOUTx = -4A | 3 |
| Current Monitor Ratio | ICLIMx /IOUTx | 0.8 | 1 | 1.2 | mA/A | When IOUTx = -2A | 3 |
| Current Limit Adjustability | ILIM(ADJ) | 0.5 | 4 | A | 3 | ||
| Accuracy of Adjustable Current Limit Threshold | -8 | 8 | % | VOUTx = VINx, 0.5V, Current Limit = 4A | 3 | ||
| Accuracy of Adjustable Current Limit Threshold | -15 | 15 | % | VOUTx = VINx, 0.5V, Current Limit = 2A | 3 | ||
| Internal Current Limit | ILIM(INT) | 4 | 6 | 9 | A | RCLIMx = 0Ω, VOUTx = 0V | 3 |
| Open-Drain Output Low Voltage | VOL | 0.05 | 0.4 | V | Current Into Open-Drain Output = 3mA | 3 | |
| Open-Drain Output High Leakage Current | 0 | 1 | µA | Open-Drain Output Voltage = 5.5V | 3 | ||
| Enable Pin Current When Pulled High | 0 | 1 | µA | VEN1 = VEN2 = 3.6V | 4 | ||
| EN1 Rising and EN2 Falling Thresholds | VENTH | 760 | 800 | 840 | mV | 4 | |
| PowerPath Turn-On Time Before Enable VOUT1 = 1.5V Diode 1 | tON | 10 | µs | Before Enable VOUT1 = 1.5V, Diode 1 | 3 | ||
| PowerPath Turn-On Time Before Enable VOUT2 = 1.5V Diode 2 | tON | 23 | µs | Before Enable VOUT2 = 1.5V, Diode 2 | 3 | ||
| PowerPath Turn-On Time Before Enable VOUTx = 0V | tON | 250 | µs | Before Enable VOUTx = 0V | 3 | ||
| PowerPath Turn-On from Shutdown Both Diodes Disabled VOUTx = 1.5V | tON(SD) | 70 | µs | Both Diodes Disabled and VOUTx = 1.5V Before Enable | 3 | ||
| PowerPath Turn-On from Shutdown Both Diodes Disabled VOUTx = 0V | tON(SD) | 320 | µs | Both Diodes Disabled and VOUTx = 0V Before Enable | 3 | ||
| PowerPath Switchover Time | tSWITCH | 9 | µs | VINx ↑ (2.6V to 4.6V) to VOUTx Starts Rising, Both Diodes Enabled, OUT1 and OUT2 Tied Together | 3 | ||
| PowerPath Turn-Off Time | tOFF | 2 | µs | Disable to IIN Falling from 100mA to 1mA | 3 | ||
| Soft-Start Duration | tSS | 2 | ms | VOUTx = 0V | 3 | ||
| Thermal Warning Threshold | TWARN | 130 | °C | Rising Temperature | 3 | ||
| Thermal Warning Hysteresis | TWARN | 15 | °C | 3 | |||
| Thermal Shutdown Threshold | TSD | 160 | °C | Rising Temperature | 3 | ||
| Thermal Shutdown Hysteresis | TSD | 20 | °C | 3 | |||
| STAT Turn-On Time EN1 Rising to STAT1 Pull-Down | tSTAT(ON) | 5 | µs | EN1 Rising to STAT1 Pull-Down | 3 | ||
| STAT Turn-On Time EN2 Falling to STAT2 Pull-Down | tSTAT(ON) | 18 | µs | EN2 Falling to STAT2 Pull-Down | 3 | ||
| STAT Turn-Off Time | tSTAT(OFF) | 2 | µs | Disable to STAT Pull-Up | 4 | ||
| WARN Turn-On Time | tWARN(ON) | 500 | µs | Current Limit to WARN Pull-Down | 4 | ||
| WARN Turn-Off Time | tWARN(OFF) | 5 | µs | Out of Current Limit to WARN Pull-Up | 4 | ||
| EN1 and EN2 Hysteresis | VENHYST | 55 | mV | 4 | |||
| Absolute Maximum Voltage IN1 IN2 OUT1 OUT2 CLIM1 CLIM2 STAT1 STAT2 WARN1 WARN2 | -0.3 | 6 | V | IN1, IN2, OUT1, OUT2, CLIM1, CLIM2, STAT1, STAT2, WARN1, WARN2 Voltage | 2 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Notes 3, 4 | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Current Limit Resistor Allowed Range | RCLIM | 125 | 1000 | Ω | Unless CLIM1/CLIM2 pins are shorted to GND | 9 | |
| Maximum Junction Temperature | TJMAX | 125 | °C | DHC package | 2 | ||
| Thermal Resistance Junction to Ambient | θJA | 43 | °C/W | DHC package, correctly soldered to 2500mm2 double-sided 1oz copper board | 12 |
CAD (KiCad official)
- Symbol:
LTC4415EDHC#PBF - Footprint:
Package_DFN_QFN:DFN-16-1EP_3x5mm_P0.5mm_EP1.66x4.4mm - 3D model: DFN-16(3x5) (KiCad packages3D, STEP)
- 3D model files:
ltc4415edhc-etched.step/ltc4415edhc-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc4415edhc.step/ltc4415edhc.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
e35970b1d556a4ba, retrieved 2026-11-19) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).