main
Ray Publish 0.1.0 58a4c06

LTC4079IDD#TRPBF

Analog Devices · Battery Management ICs · DFN-10-EP(3x3)

LTC4079IDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN power_in Input supply pin powering the battery charger (2.7V to 60V operating); bypass with a ceramic capacitor of at least 1µF.
2 EN input Enable input that starts charge current above its 1.190V regulation threshold and shuts the device down below 0.750V; must not be left floating.
3 PROG passive Charge current program pin where a resistor to ground sets constant-current charge (pin servos to 1.190V, IPROG = 1/250 of IBAT); do not leave open and keep parasitic capacitance under 50pF.
4 NTCBIAS output NTC thermistor bias output connected through a low drift bias resistor (typically equal to thermistor resistance at 25°C) to the NTC pin; minimize parasitic capacitance.
5 NTC input Battery temperature sense input for an NTC thermistor (at least 2kΩ at room temperature) that pauses charging when out of range; tie to GND to disable temperature sensing.
6 TIMER passive Timer capacitor input setting maximum charge duration with CTIMER = tTIMER • 18.2nF/Hr (100nF gives about 5½ hours); tie to GND to disable the timer and terminate at C/10.
7 CHRG output Open-drain charge status output pulled low while charging and high impedance when charge current drops below 1/10th of programmed current or the timer terminates the cycle.
8 FBG passive Ground reference for the battery voltage divider, connected to GND through an internal NMOS switch (RFBG = 160Ω) that disconnects the divider when not needed.
9 FB input Sense pin for the divided battery voltage that servos to 1.170V (VFB(CHG)) in constant-voltage phase; set by a divider from BAT to FB to FBG, minimize leakage and capacitance.
10 BAT power_out Battery charger output that provides charge current to the battery.
11 GND power_in Ground exposed pad that must be soldered to a continuous PCB ground plane for electrical connection and rated thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Supply Voltage VIN 2.7 60 V 3
Battery Voltage Range VBAT 60 V 3
VIN Undervoltage Lockout VUVLO 2.55 2.7 V VIN Rising 3
Differential Undervoltage Lockout VDUVLO -20 15 50 mV VIN-VBAT Rising 3
Differential Voltage Regulation Minimum VIN-VBAT VDVREG 120 160 200 mV Minimum VIN-VBAT for Charge Current 3
Input Supply Quiescent Current, Charging IQ(IN) 4 9 µA Charging (Note 4) 3
Input Supply Quiescent Current, Charging Terminated IQ(IN) 2 4 µA Charging Terminated (VFB = 1.210V) 3
Input Supply Quiescent Current, Shutdown IQ(IN) 0.2 0.6 µA Shutdown (EN = 0) 3
Battery Drain Current, Charging Terminated IQ(BAT) 0.01 0.2 µA Charging Terminated (VFB =1.210V) 3
Feedback Pin Regulation Voltage VFB(CHG) 1.156 1.17 1.184 V Constant-Voltage Charge Mode, over temperature 3
Battery Charge Current ICHG 236 248 260 mA RPROG = 1.2k 3
Battery Charge Current ICHG 93 99 105 mA RPROG = 3k 3
Battery Charge Current ICHG 8.5 10 11.5 mA RPROG = 30k 3
Charging Termination Threshold ITERMINATE 22 25 28 mA RPROG = 1.2k 3
Charging Termination Threshold ITERMINATE 8.2 10 11.8 mA RPROG = 3k 3
Charging Termination Threshold ITERMINATE 0.7 1 1.3 mA RPROG = 30k 3
Deglitch Filter on C/10 Charge Termination tTERMINATE 5 9 13 ms ICHG Drops Below Termination Threshold 3
Safety Timer Accuracy tTIMER -10 10 % 3
Recharge Threshold Voltage of FB Pin VRECHRG 96.9 97.6 98.3 % Relative to VFB(CHG) with VFB Falling 3
Low Battery Threshold VFB(LOWBAT) 0.78 0.8 0.82 V VFB for Low Battery Detection 3
Feedback Pin Leakage IFB 0.1 20 nA VFB = 1.170V (in Regulation) 3
Feedback Pin Leakage IFB 0.1 100 nA VFB = 8.4V (in Shutdown) 3
Feedback Ground Pin Leakage IFBG 0.1 100 nA VFBG = 8.4V, EN = 0 3
Low Temp. Fault NTC Threshold Voltage VCOLD 72.3 73.8 75.3 % VNTC/VNTCBIAS 4
High Temp. Fault NTC Threshold Voltage VHOT 35.6 36.6 37.6 % VNTC/VNTCBIAS 4
NTC Disable Voltage Threshold VNTC(DIS) 60 80 100 mV VNTC 4
NTC Input Leakage Current 0.1 100 nA VNTC = VNTCBIAS 4
EN Shutdown Threshold VEN(SD) 0.4 0.75 1.1 V VEN Falling 4
Enable Pin Regulation Voltage VEN(REG) 1.17 1.19 1.21 V Minimum VEN for Charge Current 4
Enable Pin Leakage Current When Pulled High 0 20 nA VEN = 60V 4
CHRG Output Low Voltage 0.16 0.4 V 1mA Into the Open-Drain Output 4
CHRG Output Leakage Current 0.1 100 nA VCHRG = 60V, VEN = 0V 4
Resistance of the Charge Path RON 5 Ω 3
Switch Resistance from FBG Pin to GND RFBG 160 Ω 3
Die Temperature at Thermal Regulation TJ 118 °C 3
IN, BAT, EN, CHRG, FB, FBG Voltage -0.3 62 V 2
PROG, TIMER Voltage 3 V 2
BAT Current -400 mA 2
PROG Current -1.6 mA 2
FBG Current 2 mA 2
CHRG Current 2 mA 2
Operating Junction Temperature Range TJ -40 125 °C Notes 3, 5 2
Storage Temperature Range -65 150 °C 2
Junction-to-Ambient Thermal Resistance θJA 43 °C/W DD package, TJMAX = 125°C 2

CAD (KiCad official)

  • Symbol: LTC4079IDD#TRPBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: ltc4079idd-trpbf-etched.step / ltc4079idd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc4079idd-trpbf.step / ltc4079idd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 d1866d55d66d6f92, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF