Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LTC4079IDD#TRPBF
Analog Devices · Battery Management ICs · DFN-10-EP(3x3)
LTC4079IDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input supply pin powering the battery charger (2.7V to 60V operating); bypass with a ceramic capacitor of at least 1µF. |
| 2 | EN | input | Enable input that starts charge current above its 1.190V regulation threshold and shuts the device down below 0.750V; must not be left floating. |
| 3 | PROG | passive | Charge current program pin where a resistor to ground sets constant-current charge (pin servos to 1.190V, IPROG = 1/250 of IBAT); do not leave open and keep parasitic capacitance under 50pF. |
| 4 | NTCBIAS | output | NTC thermistor bias output connected through a low drift bias resistor (typically equal to thermistor resistance at 25°C) to the NTC pin; minimize parasitic capacitance. |
| 5 | NTC | input | Battery temperature sense input for an NTC thermistor (at least 2kΩ at room temperature) that pauses charging when out of range; tie to GND to disable temperature sensing. |
| 6 | TIMER | passive | Timer capacitor input setting maximum charge duration with CTIMER = tTIMER • 18.2nF/Hr (100nF gives about 5½ hours); tie to GND to disable the timer and terminate at C/10. |
| 7 | CHRG | output | Open-drain charge status output pulled low while charging and high impedance when charge current drops below 1/10th of programmed current or the timer terminates the cycle. |
| 8 | FBG | passive | Ground reference for the battery voltage divider, connected to GND through an internal NMOS switch (RFBG = 160Ω) that disconnects the divider when not needed. |
| 9 | FB | input | Sense pin for the divided battery voltage that servos to 1.170V (VFB(CHG)) in constant-voltage phase; set by a divider from BAT to FB to FBG, minimize leakage and capacitance. |
| 10 | BAT | power_out | Battery charger output that provides charge current to the battery. |
| 11 | GND | power_in | Ground exposed pad that must be soldered to a continuous PCB ground plane for electrical connection and rated thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Voltage | VIN | 2.7 | 60 | V | 3 | ||
| Battery Voltage Range | VBAT | 60 | V | 3 | |||
| VIN Undervoltage Lockout | VUVLO | 2.55 | 2.7 | V | VIN Rising | 3 | |
| Differential Undervoltage Lockout | VDUVLO | -20 | 15 | 50 | mV | VIN-VBAT Rising | 3 |
| Differential Voltage Regulation Minimum VIN-VBAT | VDVREG | 120 | 160 | 200 | mV | Minimum VIN-VBAT for Charge Current | 3 |
| Input Supply Quiescent Current, Charging | IQ(IN) | 4 | 9 | µA | Charging (Note 4) | 3 | |
| Input Supply Quiescent Current, Charging Terminated | IQ(IN) | 2 | 4 | µA | Charging Terminated (VFB = 1.210V) | 3 | |
| Input Supply Quiescent Current, Shutdown | IQ(IN) | 0.2 | 0.6 | µA | Shutdown (EN = 0) | 3 | |
| Battery Drain Current, Charging Terminated | IQ(BAT) | 0.01 | 0.2 | µA | Charging Terminated (VFB =1.210V) | 3 | |
| Feedback Pin Regulation Voltage | VFB(CHG) | 1.156 | 1.17 | 1.184 | V | Constant-Voltage Charge Mode, over temperature | 3 |
| Battery Charge Current | ICHG | 236 | 248 | 260 | mA | RPROG = 1.2k | 3 |
| Battery Charge Current | ICHG | 93 | 99 | 105 | mA | RPROG = 3k | 3 |
| Battery Charge Current | ICHG | 8.5 | 10 | 11.5 | mA | RPROG = 30k | 3 |
| Charging Termination Threshold | ITERMINATE | 22 | 25 | 28 | mA | RPROG = 1.2k | 3 |
| Charging Termination Threshold | ITERMINATE | 8.2 | 10 | 11.8 | mA | RPROG = 3k | 3 |
| Charging Termination Threshold | ITERMINATE | 0.7 | 1 | 1.3 | mA | RPROG = 30k | 3 |
| Deglitch Filter on C/10 Charge Termination | tTERMINATE | 5 | 9 | 13 | ms | ICHG Drops Below Termination Threshold | 3 |
| Safety Timer Accuracy | tTIMER | -10 | 10 | % | 3 | ||
| Recharge Threshold Voltage of FB Pin | VRECHRG | 96.9 | 97.6 | 98.3 | % | Relative to VFB(CHG) with VFB Falling | 3 |
| Low Battery Threshold | VFB(LOWBAT) | 0.78 | 0.8 | 0.82 | V | VFB for Low Battery Detection | 3 |
| Feedback Pin Leakage | IFB | 0.1 | 20 | nA | VFB = 1.170V (in Regulation) | 3 | |
| Feedback Pin Leakage | IFB | 0.1 | 100 | nA | VFB = 8.4V (in Shutdown) | 3 | |
| Feedback Ground Pin Leakage | IFBG | 0.1 | 100 | nA | VFBG = 8.4V, EN = 0 | 3 | |
| Low Temp. Fault NTC Threshold Voltage | VCOLD | 72.3 | 73.8 | 75.3 | % | VNTC/VNTCBIAS | 4 |
| High Temp. Fault NTC Threshold Voltage | VHOT | 35.6 | 36.6 | 37.6 | % | VNTC/VNTCBIAS | 4 |
| NTC Disable Voltage Threshold | VNTC(DIS) | 60 | 80 | 100 | mV | VNTC | 4 |
| NTC Input Leakage Current | 0.1 | 100 | nA | VNTC = VNTCBIAS | 4 | ||
| EN Shutdown Threshold | VEN(SD) | 0.4 | 0.75 | 1.1 | V | VEN Falling | 4 |
| Enable Pin Regulation Voltage | VEN(REG) | 1.17 | 1.19 | 1.21 | V | Minimum VEN for Charge Current | 4 |
| Enable Pin Leakage Current When Pulled High | 0 | 20 | nA | VEN = 60V | 4 | ||
| CHRG Output Low Voltage | 0.16 | 0.4 | V | 1mA Into the Open-Drain Output | 4 | ||
| CHRG Output Leakage Current | 0.1 | 100 | nA | VCHRG = 60V, VEN = 0V | 4 | ||
| Resistance of the Charge Path | RON | 5 | Ω | 3 | |||
| Switch Resistance from FBG Pin to GND | RFBG | 160 | Ω | 3 | |||
| Die Temperature at Thermal Regulation | TJ | 118 | °C | 3 | |||
| IN, BAT, EN, CHRG, FB, FBG Voltage | -0.3 | 62 | V | 2 | |||
| PROG, TIMER Voltage | 3 | V | 2 | ||||
| BAT Current | -400 | mA | 2 | ||||
| PROG Current | -1.6 | mA | 2 | ||||
| FBG Current | 2 | mA | 2 | ||||
| CHRG Current | 2 | mA | 2 | ||||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Notes 3, 5 | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 43 | °C/W | DD package, TJMAX = 125°C | 2 |
CAD (KiCad official)
- Symbol:
LTC4079IDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ltc4079idd-trpbf-etched.step/ltc4079idd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc4079idd-trpbf.step/ltc4079idd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
d1866d55d66d6f92, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).