Generated by kicad-footprint-generator · KiCad file format 20260206
LTC4064EMSE#PBF
Analog Devices · Battery Management ICs · MSOP-10-EP
LTC4064EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CHRG | output | Open-drain charge status output that is pulled low while charging, latches to a 30µA pull-down at C/10, and goes high impedance when the timer runs out or the input supply is removed. |
| 2 | VCC | power_in | Positive input supply that operates from 4.25V to 6.5V and must be bypassed with at least a 4.7µF ceramic capacitor to ground. |
| 3 | FAULT | output | Open-drain fault status output that latches low when trickle charge times out on a low battery and pulls low, unlatched, while the NTC indicates an out-of-range temperature. |
| 4 | TIMER | passive | Timer capacitor pin where the charge time is Time (Hours) = (CTIMER × 3 hr)/(0.1µF); shorting this pin to ground disables the internal timer. |
| 5 | GND | power_in | Ground pin, one of two ground connections, which must be connected to the PC board ground plane. |
| 6 | NTC | input | NTC thermistor input that suspends charging when the voltage falls below (0.5)•(VCC) at hot temperatures or rises above (0.875)•(VCC) at cold; grounding this pin disables the NTC feature. |
| 7 | PROG | passive | Charge current program pin, where RPROG to ground sets constant-current mode with the pin servoed to 1.5V, and IBAT = (VPROG/RPROG) • 1000 gives the charge current monitor. |
| 8 | SHDN | input | Shutdown input that puts the charger into standby with BAT drain current below 3µA and supply current below 25µA when pulled to ground, and must be pulled up to VCC for normal operation. |
| 9 | BAT | power_out | Charge current output to the battery that requires a bypass capacitor of at least 1µF with a 1Ω series resistor to keep the loop stable when no battery is present, and sets the final float voltage of 4V through an internal divider. |
| 10 | ACPR | output | Open-drain power supply status output that pulls low when VCC is above the undervoltage lockout threshold and at least 35mV above VBAT, and is high impedance otherwise. |
| 11 | GND | power_in | Exposed backside pad that is ground and must be soldered to the PC board, since failure to solder it results in a thermal resistance much higher than 40°C/W. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Voltage | VCC | 4.25 | 6.5 | V | 2 | ||
| VCC Supply Current | ICC | 1 | 2 | mA | Charger On; Current Mode; RPROG = 30k (Note 5) | 2 | |
| VCC Supply Current Shutdown Mode | ICC | 25 | 50 | µA | Shutdown Mode; VSHDN = 0V | 2 | |
| VCC Supply Current Sleep Mode | ICC | 25 | 50 | µA | Sleep Mode VCC < VBAT or VCC ≤ 4V | 2 | |
| VBAT Regulated Float Voltage | VFLOAT | 3.96 | 4 | 4.04 | V | 2 | |
| Battery Pin Current | IBAT | 465 | 500 | 535 | mA | RPROG = 3k; Current Mode | 2 |
| Battery Pin Current | IBAT | 93 | 100 | 107 | mA | RPROG = 15k; Current Mode | 2 |
| Battery Pin Current Shutdown Mode | IBAT | -3 | 3 | µA | Shutdown Mode; VSHDN = 0V | 2 | |
| Battery Pin Current Sleep Mode | IBAT | -3 | 3 | µA | Sleep Mode VCC < VBAT or VCC < (VUV, ∆VUV) | 2 | |
| Trickle Charge Current | ITRIKL | 35 | 50 | 65 | mA | VBAT < 2V; RPROG = 3k | 2 |
| VCC Undervoltage Lockout Voltage | VUV | 4 | 4.25 | V | VCC Rising | 2 | |
| Manual Shutdown Threshold Voltage | VMSD | 0.6 | 1.3 | V | SHDN Pin Voltage | 2 | |
| Input Supply Voltage absolute maximum | VCC | 10 | V | Input Supply Voltage (VCC) | 2 | ||
| BAT Pin Voltage absolute maximum | VBAT | 10 | V | BAT pin | 2 | ||
| NTC, SHDN, TIMER, PROG Pin Voltage | -0.3 | V | Upper limit VCC + 0.3V | 2 | |||
| CHRG, FAULT, ACPR Pin Voltage | -0.3 | 10 | V | 2 | |||
| BAT Current | IBAT | 1.3 | A | Note 2 | 2 | ||
| PROG Current | IPROG | 1.3 | mA | Note 2 | 2 | ||
| Junction Temperature | TJ | 125 | °C | 2 | |||
| Operating Temperature Range | TA | -40 | 85 | °C | Note 3 | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 2 | |||
| Thermal Resistance Junction to Ambient | θJA | 40 | °C/W | Soldered exposed pad to PC board (Note 4) | 2 | ||
| Trickle Charge Trip Threshold Voltage | VTRIKL | 2.48 | V | VBAT Rising | 2 | ||
| Trickle Charge Trip Hysteresis Voltage | ∆VTRIKL | 100 | mV | 2 | |||
| VCC Undervoltage Lockout Hysteresis | ∆VUV | 200 | mV | 2 | |||
| Automatic Shutdown Threshold Voltage High to Low | VASD | 35 | mV | (VCC - VBAT) High to Low | 2 | ||
| Automatic Shutdown Threshold Voltage Low to High | VASD | 70 | mV | (VCC - VBAT) Low to High | 2 | ||
| Charge Current Monitor PROG Pin Voltage | VPROG | 1.5 | V | RPROG = 3k, IPROG = 500µA | 3 | ||
| CHRG Pin Weak Pulldown Current | ICHRG | 15 | 30 | 50 | µA | VCHRG = 1V | 3 |
| CHRG Pin Output Low Voltage | VCHRG | 0.35 | 0.6 | V | ICHRG = 5mA | 3 | |
| ACPR Pin Output Low Voltage | VACPR | 0.35 | 0.6 | V | IACPR = 5mA | 3 | |
| FAULT Pin Output Low Voltage | VFAULT | 0.35 | 0.6 | V | IFAULT = 5mA | 3 | |
| End of Charge Indication Current Level | IC/10 | 44 | 50 | 56 | mA | RPROG = 3k | 3 |
| TIMER Accuracy | tTIMER | 10 | % | CTIMER = 0.1µF | 3 | ||
| Recharge Threshold Voltage | ∆VRECHRG | 65 | 100 | 135 | mV | VFLOAT - VRECHRG, VBAT > VTRIKL; Charge Termination Timer Expired | 3 |
| NTC Pin Hot Threshold Voltage | VNTC-HOT | 2.5 | V | VNTC Falling | 3 | ||
| NTC Pin Hot Hysteresis Voltage | VHOT-HYS | 80 | mV | 3 | |||
| NTC Pin Cold Threshold Voltage | VNTC-COLD | 4.375 | V | VNTC Rising | 3 | ||
| NTC Pin Cold Hysteresis Voltage | VCOLD-HYS | 80 | mV | 3 | |||
| NTC Pin Disable Threshold Voltage | VNTC-DIS | 100 | mV | VNTC Rising | 3 | ||
| NTC Pin Disable Hysteresis Voltage | VDIS-HYS | 10 | mV | 3 | |||
| Junction Temperature in Constant-Temperature Mode | TLIM | 105 | °C | 3 | |||
| Power MOSFET ON Resistance | RON | 375 | mΩ | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | thermal contact between the exposed pad on the backside of the package and the copper board will result in thermal | 13 |
CAD (KiCad official)
- Symbol:
LTC4064EMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
ltc4064emse-pbf-etched.step/ltc4064emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc4064emse-pbf.step/ltc4064emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
f296ef91ee5a46c4, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).