3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC2862IS8-1#PBF
Analog Devices · RS-485/RS-422 ICs · SO-8
LTC2862IS8-1#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: high when A-B > 200mV and low when A-B < -200mV with RE low, and high if the inputs are open, shorted, or terminated without a signal. |
| 2 | RE | input | Receiver enable: a low input enables the receiver, a high input forces RO into high impedance, and RE high with DE low puts the part into low power shutdown. |
| 3 | DE | input | Driver enable: a high input enables the driver, a low input forces the driver outputs into high impedance, and DE low with RE high puts the part into low power shutdown. |
| 4 | DI | input | Driver input: with the driver enabled (DE high), a low on DI forces the noninverting driver output low and the inverting output high, and a high on DI forces the reverse. |
| 5 | GND | power_in | Ground. |
| 6 | A | bidirectional | Noninverting receiver input and noninverting driver output for the LTC2862; impedance is > 96kΩ in receive mode or when unpowered. |
| 7 | B | bidirectional | Inverting receiver input and inverting driver output for the LTC2862; impedance is > 96kΩ in receive mode or when unpowered. |
| 8 | VCC | power_in | Power supply: 3V < VCC < 5.5V, bypass with a 0.1µF ceramic capacitor to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Communication Interface Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Primary Power Supply (VCC) | VCC | 3 | 5.5 | V | 4 | ||
| Operating Ambient Temperature Range (LTC286xI) | TA | -40 | 85 | °C | I-grade | 2 | |
| Supply Current in Shutdown Mode (C-, I-Grade) | ICCS | 0 | 5 | µA | DE = 0V, RE = VCC = VL | 4 | |
| Supply Current with Both Driver and Receiver Enabled (LTC2862-1) | ICCTR | 900 | 1300 | µA | No Load, DE = VCC = VL, RE = 0V | 4 | |
| Differential Driver Output Voltage (R = ∞) | /VOD/ | 1.5 | V | R = ∞ (Figure 1) | 5 | ||
| Differential Driver Output Voltage (R = 27Ω) | /VOD/ | 1.5 | 5 | V | R = 27Ω (Figure 1) | 5 | |
| Differential Driver Output Voltage (R = 50Ω) | /VOD/ | 2 | V | R = 50Ω (Figure 1) | 5 | ||
| Change in Magnitude of Driver Differential Output Voltage | Δ/VOD/ | 0.2 | V | R = 27Ω or 50Ω (Figure 1) | 5 | ||
| Driver Common-Mode Output Voltage | VOC | 3 | V | R = 27Ω or 50Ω (Figure 1) | 5 | ||
| Change in Magnitude of Driver Common-Mode Output Voltage | Δ/VOC/ | 0.2 | V | R = 27Ω or 50Ω (Figure 1) | 5 | ||
| Maximum Driver Short-Circuit Current | IOSD | -250 | 150 | 250 | mA | -60V ≤ (Y or Z) ≤ 60V (Figure 2) | 5 |
| Driver Three-State Output Current on Y and Z | IOZD | -30 | 30 | µA | DE = 0V, VCC = 0V or 3.3V, VO = -25V, 25V | 5 | |
| Receiver Input Current (A,B) at VIN = 12V (H-/MP-grade row, applies to LTC2862) | IIN | 143 | µA | VCC = 0V or 3.3V, VIN = 12V (Figure 3) | 5 | ||
| Receiver Input Current (A,B) at VIN = -7V (LTC2862) | IIN | -100 | µA | VCC = 0V or 3.3V, VIN = -7V (Figure 3) | 5 | ||
| Receiver Input Resistance | RIN | 112 | kΩ | 0 ≤ VCC ≤ 5.5V, VIN = -25V or 25V (Figure 3) | 5 | ||
| Receiver Common Mode Input Voltage | VCM | -25 | 25 | V | (A + B)/2 | 5 | |
| Differential Input Signal Threshold Voltage (A, B) | VTH | -200 | 200 | mV | -25V ≤ VCM ≤ 25V | 5 | |
| Differential Input Signal Hysteresis | ΔVTH | 150 | mV | VCM = 0V | 5 | ||
| Differential Input Failsafe Threshold Voltage | -200 | -50 | 0 | mV | -25V ≤ VCM ≤ 25V | 5 | |
| Differential Input Failsafe Hysteresis | 25 | mV | VCM = 0V | 5 | |||
| Receiver Output Low Voltage | VOL | 0.4 | V | I(RO) = 3mA (Sinking) | 5 | ||
| Receiver Three-State Output Current on RO | IOZR | -5 | 5 | µA | RE = High, RO = 0V or VCC | 5 | |
| Receiver Short-Circuit Current | IOSR | -20 | 20 | mA | RE = Low, RO = 0V or VCC | 5 | |
| Logic Input Current (DE, DI, RE) | IINL | -5 | 5 | µA | 0 ≤ VIN ≤ VCC | 5 | |
| Maximum Data Rate (20 Mbps mode, LTC2862-1) | fMAX | 20 | Mbps | 6 | |||
| Driver Input to Output (high speed) | tPLHD, tPHLD | 25 | 50 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 6 | |
| Driver Input to Output Difference | ΔtPD | 2 | 9 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 6 | |
| Driver Output Y to Output Z Skew | tSKEWD | -10 | 10 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 6 | |
| Driver Rise or Fall Time (high speed) | tRD, tFD | 4 | 15 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 6 | |
| Driver Enable or Disable Time | tZLD, tZHD, tLZD, tHZD | 180 | ns | RL = 500Ω, CL = 50pF, RE = 0V (Figure 5) | 6 | ||
| Driver Enable from Shutdown | tZHSD, tZLSD | 9 | µs | RL = 500Ω, CL = 50pF, RE = High (Figure 5) | 6 | ||
| Time to Shutdown (driver) | tSHDND | 180 | ns | RL = 500Ω, CL = 50pF, RE = High (Figure 5) | 6 | ||
| Receiver Input to Output | tPLHR, tPHLR | 50 | 65 | ns | CL = 15pF, VCM = 1.5V, /VAB/ = 1.5V, tR and tF < 4ns (Figure 6) | 6 | |
| Differential Receiver Skew | tSKEWR | 2 | 9 | ns | CL = 15pF (Figure 6) | 6 | |
| Receiver Output Rise or Fall Time | tRR, tFR | 3 | 12.5 | ns | CL = 15pF (Figure 6) | 6 | |
| Receiver Enable/Disable Time | tZLR, tZHR, tLZR, tHZR | 40 | ns | RL = 1k, CL = 15pF, DE = High (Figure 7) | 6 | ||
| Receiver Enable from Shutdown | tZHSR, tZLSR | 9 | µs | RL = 1k, CL = 15pF, DE = 0V (Figure 7) | 6 | ||
| Time to Shutdown (receiver) | tSHDNR | 100 | ns | RL = 1k, CL = 15pF, DE = 0V (Figure 7) | 6 | ||
| Supply Voltage (absolute maximum) | VCC | -0.3 | 6 | V | 2 | ||
| Logic Input Voltages (absolute maximum) | RE, DE, DI | -0.3 | 6 | V | 2 | ||
| Interface I/O Voltage (absolute maximum) | A, B | -60 | 60 | V | 2 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Maximum Junction Temperature | TJMAX | 150 | °C | S8 package | 2 | ||
| Thermal Resistance, Junction to Ambient (S8) | θJA | 150 | °C/W | S8 package | 2 | ||
| Thermal Resistance, Junction to Case (S8) | θJC | 39 | °C/W | S8 package | 2 |
CAD (KiCad official)
- Symbol:
LTC2862IS8-1#PBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
ltc2862is8-1-pbf-etched.step/ltc2862is8-1-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2862is8-1-pbf.step/ltc2862is8-1-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
156a32e263226c9f, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).