main
Ray
Publish 0.1.0
5e34d3d
LTC2804IGN-1#PBF
Analog Devices · RS232 ICs · SSOP-16-150mil
LTC2804IGN-1#PBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R1IN | input | RS-232 receiver 1 input with an internal 5kΩ termination resistor, rated for -25V to 25V. |
| 2 | R2IN | input | RS-232 receiver 2 input with an internal 5kΩ termination resistor, rated for -25V to 25V. |
| 3 | T1OUT | output | RS-232 driver 1 output, rated for -15V to 15V and protected against shorts to ground or up to ±15V. |
| 4 | T2OUT | output | RS-232 driver 2 output, rated for -15V to 15V and protected against shorts to ground or up to ±15V. |
| 5 | VCC | power_in | Input supply, 1.8V to 5.5V; bypass to GND with a 1µF capacitor. |
| 6 | VDD | power_out | Generated positive supply for the RS-232 driver (7V nominal); connect a 1µF capacitor between VDD and GND. |
| 7 | SW | output | DC-DC switch pin; connect a 10µH inductor between SW and VCC. |
| 8 | GND | power_in | Ground reference for all supplies and signals. |
| 9 | VEE | power_out | Generated negative supply for the RS-232 driver (-6.3V); connect a 1µF capacitor between VEE and GND. |
| 10 | CAP | passive | Charge pump capacitor for the negative supply; connect a 220nF capacitor between CAP and SW. |
| 11 | ON/OFF | input | Transceiver enable referenced to VL; a logic low places the device in Shutdown with driver and receiver outputs high impedance. |
| 12 | VL | power_in | Logic supply, 1.8V to 5.5V, for receiver outputs, driver inputs and control inputs; bypass with 220nF if not tied to VCC. |
| 13 | T2IN | input | Driver 2 input referenced to VL. |
| 14 | T1IN | input | Driver 1 input referenced to VL. |
| 15 | R2OUT | output | Receiver 2 output referenced to VL, short-circuit protected to GND/VCC/VL and high impedance in Shutdown. |
| 16 | R1OUT | output | Receiver 1 output referenced to VL, short-circuit protected to GND/VCC/VL and high impedance in Shutdown. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Current, Normal Mode | ICC | 2.3 | 10 | mA | Outputs Unloaded, Normal Mode (Note 3) | 3 | |
| VCC Supply Current, Receivers Active Mode | ICC | 1 | 10 | µA | Outputs Unloaded, Receivers Active Mode | 3 | |
| VL Supply Current, Normal Mode (LTC2803, LTC2804) | IL | 0.15 | 0.3 | mA | Outputs Unloaded, Normal Mode (LTC2803, LTC2804) | 3 | |
| VL Supply Current, Receivers Active Mode | IL | 15 | 30 | µA | Receivers Active Mode | 3 | |
| VL Supply Current, Shutdown Mode | IL | 1 | 10 | µA | Shutdown Mode | 3 | |
| Driver Output Voltage Low | VOLD | -5.7 | -5 | V | RL = 3kΩ | 3 | |
| Driver Output Voltage High | VOHD | 5 | 6.2 | V | RL = 3kΩ | 3 | |
| Driver Output Short Circuit Current | IOSD | -70 | 35 | 70 | mA | VL = VCC = 5.5V; VTOUT = 0V | 3 |
| Driver Power-Off Output Leakage Current | IPOLD | -10 | 0.1 | 10 | µA | VL = VCC = VDD = VEE = 0V; VTOUT = ±2V | 3 |
| Driver Output Leakage Current | IOLD | -10 | 0.1 | 10 | µA | Shutdown or Receivers Active or Drivers Disabled Modes, -15V ≤ VTOUT ≤ 15V | 3 |
| Receiver Input Threshold, Receivers Active Mode | VIR | 0.8 | 1.5 | 2.4 | V | Receivers Active Mode | 3 |
| Receiver Input Threshold, Input Low | VILR | 0.8 | 1.3 | V | Normal Mode, Input Low | 3 | |
| Receiver Input Threshold, Input High | VIHR | 1.7 | 2.5 | V | Normal Mode, Input High | 3 | |
| Receiver Input Hysteresis | VHYSR | 0.1 | 0.4 | 1 | V | Normal Mode | 3 |
| Receiver Output Voltage Low | VOLR | 0.2 | 0.4 | V | Output Low, IROUT = 1mA (Sinking) | 3 | |
| Receiver Input Resistance | RIN | 3 | 5 | 7 | kΩ | -15V ≤ VRIN ≤ 15V | 3 |
| Receiver Output Short Circuit Current | IOSR | -50 | 25 | 50 | mA | VL = 5.5V; 0V ≤ VROUT ≤ VL | 3 |
| Logic Input Current | IIN | -1 | 1 | µA | 3 | ||
| Maximum Data Rate, LTC2804 at 2.5nF | 100 | kbps | RL = 3kΩ, CL = 2.5nF | 4 | |||
| Maximum Data Rate, LTC2804 at 1nF | 250 | kbps | RL = 3kΩ, CL = 1nF | 4 | |||
| Maximum Data Rate, LTC2804 at 250pF | 1000 | kbps | RL = 3kΩ, CL = 250pF | 4 | |||
| Driver Slew Rate, LTC2804 at 1.8V | SR(D) | 4 | V/µs | VCC = VL = 1.8V, RL = 3kΩ, CL = 2.5nF | 4 | ||
| Driver Slew Rate, LTC2804 at 5.5V | SR(D) | 150 | V/µs | VCC = VL = 5.5V, RL = 3kΩ, CL = 50pF | 4 | ||
| Driver Propagation Delay, LTC2804 | tPHLD, tPLHD | 0.2 | 0.5 | µs | RL = 3kΩ, CL = 50pF | 4 | |
| Driver Skew, LTC2804 | tSKEWD | 50 | ns | RL = 3kΩ, CL = 50pF | 4 | ||
| Driver Output Enable Time | tPZHD, tPZLD | 0.6 | 2 | µs | PS = VL, MODE = ↑, RL = 3kΩ, CL = 50pF | 4 | |
| Driver Output Disable Time | tPHZD, tPLZD | 0.3 | 2 | µs | PS = VL, MODE = ↓, RL = 3kΩ, CL = 50pF | 4 | |
| Receiver Propagation Delay | tPHLR, tPLHR | 0.2 | 0.4 | µs | CL = 150pF | 4 | |
| Receiver Skew | tSKEWR | 50 | ns | CL = 150pF | 4 | ||
| Receiver Rise or Fall Time | tRR, tFR | 60 | 200 | ns | CL = 150pF | 4 | |
| Shutdown to Receiver Output Enable | tPZHR, tPZLR | 5 | 15 | µs | PS = MODE = ↑ or ON/OFF = ↑, RL = 1kΩ, CL = 150pF | 4 | |
| Receiver Output Disable upon Shutdown | tPHZR, tPLZR | 0.15 | 0.3 | µs | PS = MODE = ↓ or ON/OFF = ↓, RL = 1kΩ, CL = 150pF | 4 | |
| VDD/VEE Supply Rise Time | 0.2 | 2 | ms | Notes 3 and 4 | 4 | ||
| VCC Input Supply Voltage | VCC | 1.8 | 5.5 | V | Electrical characteristics range | 3 | |
| VL Logic Supply Voltage | VL | 1.8 | 5.5 | V | Electrical characteristics range | 3 | |
| Operating Temperature (LTC280XI grade) | TA | -40 | 85 | °C | I-grade (LTC280XI) | 2 | |
| VCC Supply Voltage | VCC | -0.3 | 7 | V | 2 | ||
| VL Supply Voltage | VL | -0.3 | 6.7 | V | 2 | ||
| VDD Generated Supply Voltage | VDD | 7.5 | V | 2 | |||
| VEE Generated Supply Voltage | VEE | -7.5 | 0.3 | V | 2 | ||
| VDD to VEE Differential | VDD, VEE | 14 | V | 2 | |||
| Switch Pin Voltage | SW | -0.3 | V | 2 | |||
| Charge Pump Capacitor Pin Voltage | CAP | 0.3 | V | 2 | |||
| Driver and Mode Input Voltage | TIN, T1IN, T2IN, MODE | -0.3 | 7 | V | 2 | ||
| PS and ON/OFF Input Voltage | PS, ON/OFF | -0.3 | V | 2 | |||
| Receiver Input Voltage | RIN, R1IN, R2IN | -25 | 25 | V | 2 | ||
| Driver Output Voltage | TOUT, T1OUT, T2OUT | -15 | 15 | V | 2 | ||
| Receiver Output Voltage | ROUT, R1OUT, R2OUT | -0.3 | V | 2 | |||
| Storage Temperature Range | TSTG | -65 | 125 | °C | 2 | ||
| Maximum Junction Temperature, GN Package | TJMAX | 125 | °C | GN16 SSOP | 2 | ||
| Thermal Resistance, Junction to Ambient, GN Package | θJA | 110 | °C/W | 4 Layer | 2 | ||
| Thermal Resistance, Junction to Case, GN Package | θJC | 40 | °C/W | 4 Layer | 2 |
CAD (KiCad official)
- Symbol:
LTC2804IGN-1#PBF - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
ltc2804ign-1-etched.step/ltc2804ign-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2804ign-1.step/ltc2804ign-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (18 pp, sha256
e9ad4ef1183d2db6, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC2804IGN-1#PBF
**Analog Devices** · RS232 ICs · SSOP-16-150mil
LTC2804IGN-1#PBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R1IN | input | RS-232 receiver 1 input with an internal 5kΩ termination resistor, rated for -25V to 25V. |
| 2 | R2IN | input | RS-232 receiver 2 input with an internal 5kΩ termination resistor, rated for -25V to 25V. |
| 3 | T1OUT | output | RS-232 driver 1 output, rated for -15V to 15V and protected against shorts to ground or up to ±15V. |
| 4 | T2OUT | output | RS-232 driver 2 output, rated for -15V to 15V and protected against shorts to ground or up to ±15V. |
| 5 | VCC | power_in | Input supply, 1.8V to 5.5V; bypass to GND with a 1µF capacitor. |
| 6 | VDD | power_out | Generated positive supply for the RS-232 driver (7V nominal); connect a 1µF capacitor between VDD and GND. |
| 7 | SW | output | DC-DC switch pin; connect a 10µH inductor between SW and VCC. |
| 8 | GND | power_in | Ground reference for all supplies and signals. |
| 9 | VEE | power_out | Generated negative supply for the RS-232 driver (-6.3V); connect a 1µF capacitor between VEE and GND. |
| 10 | CAP | passive | Charge pump capacitor for the negative supply; connect a 220nF capacitor between CAP and SW. |
| 11 | ON/OFF | input | Transceiver enable referenced to VL; a logic low places the device in Shutdown with driver and receiver outputs high impedance. |
| 12 | VL | power_in | Logic supply, 1.8V to 5.5V, for receiver outputs, driver inputs and control inputs; bypass with 220nF if not tied to VCC. |
| 13 | T2IN | input | Driver 2 input referenced to VL. |
| 14 | T1IN | input | Driver 1 input referenced to VL. |
| 15 | R2OUT | output | Receiver 2 output referenced to VL, short-circuit protected to GND/VCC/VL and high impedance in Shutdown. |
| 16 | R1OUT | output | Receiver 1 output referenced to VL, short-circuit protected to GND/VCC/VL and high impedance in Shutdown. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Current, Normal Mode | ICC | | 2.3 | 10 | mA | Outputs Unloaded, Normal Mode (Note 3) | 3 |
| VCC Supply Current, Receivers Active Mode | ICC | | 1 | 10 | µA | Outputs Unloaded, Receivers Active Mode | 3 |
| VL Supply Current, Normal Mode (LTC2803, LTC2804) | IL | | 0.15 | 0.3 | mA | Outputs Unloaded, Normal Mode (LTC2803, LTC2804) | 3 |
| VL Supply Current, Receivers Active Mode | IL | | 15 | 30 | µA | Receivers Active Mode | 3 |
| VL Supply Current, Shutdown Mode | IL | | 1 | 10 | µA | Shutdown Mode | 3 |
| Driver Output Voltage Low | VOLD | | -5.7 | -5 | V | RL = 3kΩ | 3 |
| Driver Output Voltage High | VOHD | 5 | 6.2 | | V | RL = 3kΩ | 3 |
| Driver Output Short Circuit Current | IOSD | -70 | 35 | 70 | mA | VL = VCC = 5.5V; VTOUT = 0V | 3 |
| Driver Power-Off Output Leakage Current | IPOLD | -10 | 0.1 | 10 | µA | VL = VCC = VDD = VEE = 0V; VTOUT = ±2V | 3 |
| Driver Output Leakage Current | IOLD | -10 | 0.1 | 10 | µA | Shutdown or Receivers Active or Drivers Disabled Modes, -15V ≤ VTOUT ≤ 15V | 3 |
| Receiver Input Threshold, Receivers Active Mode | VIR | 0.8 | 1.5 | 2.4 | V | Receivers Active Mode | 3 |
| Receiver Input Threshold, Input Low | VILR | 0.8 | 1.3 | | V | Normal Mode, Input Low | 3 |
| Receiver Input Threshold, Input High | VIHR | 1.7 | 2.5 | | V | Normal Mode, Input High | 3 |
| Receiver Input Hysteresis | VHYSR | 0.1 | 0.4 | 1 | V | Normal Mode | 3 |
| Receiver Output Voltage Low | VOLR | | 0.2 | 0.4 | V | Output Low, IROUT = 1mA (Sinking) | 3 |
| Receiver Input Resistance | RIN | 3 | 5 | 7 | kΩ | -15V ≤ VRIN ≤ 15V | 3 |
| Receiver Output Short Circuit Current | IOSR | -50 | 25 | 50 | mA | VL = 5.5V; 0V ≤ VROUT ≤ VL | 3 |
| Logic Input Current | IIN | -1 | | 1 | µA | | 3 |
| Maximum Data Rate, LTC2804 at 2.5nF | | 100 | | | kbps | RL = 3kΩ, CL = 2.5nF | 4 |
| Maximum Data Rate, LTC2804 at 1nF | | 250 | | | kbps | RL = 3kΩ, CL = 1nF | 4 |
| Maximum Data Rate, LTC2804 at 250pF | | 1000 | | | kbps | RL = 3kΩ, CL = 250pF | 4 |
| Driver Slew Rate, LTC2804 at 1.8V | SR(D) | 4 | | | V/µs | VCC = VL = 1.8V, RL = 3kΩ, CL = 2.5nF | 4 |
| Driver Slew Rate, LTC2804 at 5.5V | SR(D) | 150 | | | V/µs | VCC = VL = 5.5V, RL = 3kΩ, CL = 50pF | 4 |
| Driver Propagation Delay, LTC2804 | tPHLD, tPLHD | | 0.2 | 0.5 | µs | RL = 3kΩ, CL = 50pF | 4 |
| Driver Skew, LTC2804 | tSKEWD | | | 50 | ns | RL = 3kΩ, CL = 50pF | 4 |
| Driver Output Enable Time | tPZHD, tPZLD | | 0.6 | 2 | µs | PS = VL, MODE = ↑, RL = 3kΩ, CL = 50pF | 4 |
| Driver Output Disable Time | tPHZD, tPLZD | | 0.3 | 2 | µs | PS = VL, MODE = ↓, RL = 3kΩ, CL = 50pF | 4 |
| Receiver Propagation Delay | tPHLR, tPLHR | | 0.2 | 0.4 | µs | CL = 150pF | 4 |
| Receiver Skew | tSKEWR | | | 50 | ns | CL = 150pF | 4 |
| Receiver Rise or Fall Time | tRR, tFR | | 60 | 200 | ns | CL = 150pF | 4 |
| Shutdown to Receiver Output Enable | tPZHR, tPZLR | | 5 | 15 | µs | PS = MODE = ↑ or ON/OFF = ↑, RL = 1kΩ, CL = 150pF | 4 |
| Receiver Output Disable upon Shutdown | tPHZR, tPLZR | | 0.15 | 0.3 | µs | PS = MODE = ↓ or ON/OFF = ↓, RL = 1kΩ, CL = 150pF | 4 |
| VDD/VEE Supply Rise Time | | | 0.2 | 2 | ms | Notes 3 and 4 | 4 |
| VCC Input Supply Voltage | VCC | 1.8 | | 5.5 | V | Electrical characteristics range | 3 |
| VL Logic Supply Voltage | VL | 1.8 | | 5.5 | V | Electrical characteristics range | 3 |
| Operating Temperature (LTC280XI grade) | TA | -40 | | 85 | °C | I-grade (LTC280XI) | 2 |
| VCC Supply Voltage | VCC | -0.3 | | 7 | V | | 2 |
| VL Supply Voltage | VL | -0.3 | | 6.7 | V | | 2 |
| VDD Generated Supply Voltage | VDD | | | 7.5 | V | | 2 |
| VEE Generated Supply Voltage | VEE | -7.5 | | 0.3 | V | | 2 |
| VDD to VEE Differential | VDD, VEE | | | 14 | V | | 2 |
| Switch Pin Voltage | SW | -0.3 | | | V | | 2 |
| Charge Pump Capacitor Pin Voltage | CAP | | | 0.3 | V | | 2 |
| Driver and Mode Input Voltage | TIN, T1IN, T2IN, MODE | -0.3 | | 7 | V | | 2 |
| PS and ON/OFF Input Voltage | PS, ON/OFF | -0.3 | | | V | | 2 |
| Receiver Input Voltage | RIN, R1IN, R2IN | -25 | | 25 | V | | 2 |
| Driver Output Voltage | TOUT, T1OUT, T2OUT | -15 | | 15 | V | | 2 |
| Receiver Output Voltage | ROUT, R1OUT, R2OUT | -0.3 | | | V | | 2 |
| Storage Temperature Range | TSTG | -65 | | 125 | °C | | 2 |
| Maximum Junction Temperature, GN Package | TJMAX | | | 125 | °C | GN16 SSOP | 2 |
| Thermal Resistance, Junction to Ambient, GN Package | θJA | | 110 | | °C/W | 4 Layer | 2 |
| Thermal Resistance, Junction to Case, GN Package | θJC | | 40 | | °C/W | 4 Layer | 2 |
## CAD (KiCad official)
- Symbol: `LTC2804IGN-1#PBF`
- Footprint: `Package_SO:SSOP-16_3.9x4.9mm_P0.635mm`
- 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files: `ltc2804ign-1-etched.step` / `ltc2804ign-1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc2804ign-1.step` / `ltc2804ign-1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/2801234fe.pdf) (18 pp, sha256 `e9ad4ef1183d2db6`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc2804ign-1-datasheet.pdf)