main
Ray Publish 0.1.0 ea6f4f8

LTC2485CDD#TRPBF

Analog Devices · Analog To Digital Converters (ADCs) · DFN-10-EP(3x3)

LTC2485CDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 REF+ input Positive differential reference input, which may be anywhere between GND and VCC but must be at least 0.1V more positive than REF-.
2 VCC power_in Positive supply voltage, specified for 2.7V to 5.5V operation and to be bypassed to GND (pin 8) with a 1µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor.
3 REF- input Negative differential reference input, which may be anywhere between GND and VCC and must be at least 0.1V less positive than REF+.
4 IN+ input Positive differential analog input, which may range from GND - 0.3V to VCC + 0.3V, with bipolar input range VIN = IN+ - IN- of -0.5 x VREF to 0.5 x VREF.
5 IN- input Negative differential analog input, which may range from GND - 0.3V to VCC + 0.3V, forming the differential input with IN+ over -0.5 x VREF to 0.5 x VREF.
6 SCL input I2C serial clock input, accepting only an external clock since the LTC2485 operates only as a slave; data is shifted into SDA on SCL rising edges and output on falling edges.
7 SDA bidirectional I2C bidirectional serial data line, which is an open-drain N-channel driver in data output mode and requires an external pull-up resistor or current source to VCC.
8 GND power_in Ground; connect to a ground plane through a low impedance connection.
9 CA1 input Three-state (LOW, HIGH, or Floating) chip address control pin that sets bit CA1 of the device I2C address.
10 CA0/f0 input Two-state (HIGH or Floating) chip address control pin for CA0 in I2C address; when driven by an external clock of at least 10kHz it becomes the system clock input with the digital filter null at fEOSC/5120.
11 GND (EP) power_in Exposed pad is GND and must be soldered to the PCB.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Data Converters
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Integral Nonlinearity INL 2 ppm of VREF 5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V 2
Integral Nonlinearity INL 1 ppm of VREF 2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V 2
Offset Error VOS 0.5 2.5 µV 2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN- ≤ VCC 2
Positive Full-Scale Error 25 ppm of VREF 2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN- = 0.25VREF 2
Negative Full-Scale Error 25 ppm of VREF 2.5V ≤ VREF ≤ VCC, IN- = 0.75VREF, IN+ = 0.25VREF 2
Total Unadjusted Error 15 ppm of VREF 5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V 2
Internal PTAT Signal VPTAT 390 450 mV TA = 27°C 2
Offset Error (2x Speed) VOS 0.5 2 mV 2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN- ≤ VCC 3
Input Common Mode Rejection DC CMRR 140 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Input Common Mode Rejection 50Hz ±2% CMRR 140 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Input Common Mode Rejection 60Hz ±2% CMRR 140 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Input Normal Mode Rejection 50Hz ±2% NMRR 110 120 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Input Normal Mode Rejection 60Hz ±2% NMRR 110 120 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Input Normal Mode Rejection 50Hz/60Hz ±2% NMRR 87 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Reference Common Mode Rejection DC CMRR 120 140 dB 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC 3
Power Supply Rejection DC PSRR 120 dB VREF = 2.5V, IN- = IN+ = GND 3
Power Supply Rejection 50Hz ±2% PSRR 120 dB VREF = 2.5V, IN- = IN+ = GND 3
Power Supply Rejection 60Hz ±2% PSRR 120 dB VREF = 2.5V, IN- = IN+ = GND 3
IN+ Absolute/Common Mode Voltage IN+ -0.3 V Max printed as VCC + 0.3V 3
IN- Absolute/Common Mode Voltage IN- -0.3 V Max printed as VCC + 0.3V 3
Reference Voltage Range (REF+, REF-) VREF 0.1 V Upper limit printed as VCC 3
IN+ DC Leakage Current IDC_LEAK (IN+) -10 1 10 nA Sleep mode, IN+ = GND 4
IN- DC Leakage Current IDC_LEAK (IN-) -10 1 10 nA Sleep mode, IN- = GND 4
REF+, REF- DC Leakage Current IDC_LEAK (VREF) -100 1 100 nA Sleep mode, VREF = VCC 4
Low Level Output Voltage VOL 0.4 V SDA I = 3mA 4
Output Fall Time from VIHMIN to VILMAX tOF 250 ns Bus Load CB 10pF to 400pF 4
Input Spike Suppression tSP 50 ns 4
Input Leakage IIN 1 µA 0.1VCC ≤ VIN ≤ VCC 4
Capacitance for Each I/O Pin CI 10 pF 4
Capacitance Load for Each Bus Line CB 400 pF 4
Digital Input Current II -10 10 µA 4
Low Level CA0/f0 External Oscillator Input Voltage VIL(EXT,OSC) 0.5 V 2.7V ≤ VCC < 5.5V 4
Supply Voltage VCC 2.7 5.5 V 4
Supply Current Conversion Mode ICC 160 250 µA Conversion mode (internal oscillator) 4
Supply Current Sleep Mode ICC 1 2 µA Sleep mode (internal oscillator) 4
External Oscillator Frequency Range fEOSC 10 1000 kHz 5
External Oscillator High Period tHEO 0.125 100 µs 5
External Oscillator Low Period tLEO 0.125 100 µs 5
Conversion Time 1x Speed 50Hz Mode tCONV_1 157.2 160.3 163.5 ms Internal oscillator 5
Conversion Time 1x Speed 60Hz Mode tCONV_1 131 133.6 136.3 ms Internal oscillator 5
Conversion Time 1x Speed Simultaneous 50Hz/60Hz Mode tCONV_1 144.1 146.9 149.9 ms Internal oscillator 5
Conversion Time 2x Speed 50Hz Mode tCONV_2 78.7 80.3 81.9 ms Internal oscillator 5
Conversion Time 2x Speed 60Hz Mode tCONV_2 65.6 66.9 68.2 ms Internal oscillator 5
Conversion Time 2x Speed Simultaneous 50Hz/60Hz Mode tCONV_2 72.2 73.6 75.1 ms Internal oscillator 5
SCL Clock Frequency fSCL 0 400 kHz 5
Hold Time (Repeated) START Condition tHD(SDA) 0.6 µs 5
LOW Period of the SCL Clock tLOW 1.3 µs 5
HIGH Period of the SCL Clock tHIGH 0.6 µs 5
Set-Up Time for a Repeated START Condition tSU(STA) 0.6 µs 5
Data Hold Time tHD(DAT) 0 0.9 µs 5
Data Set-Up Time tSU(DAT) 100 ns 5
Rise Time for Both SDA and SCL Signals tr 300 ns Note 14 5
Fall Time for Both SDA and SCL Signals tf 300 ns Note 14 5
Set-Up Time for STOP Condition tSU(STO) 0.6 µs 5
Supply Voltage to GND (absolute maximum) VCC -0.3 6 V Voltage with respect to GND 2
Operating Temperature Range LTC2485C TA 0 70 °C LTC2485C grade 2
Storage Temperature Range TSTG -65 125 °C 2
Thermal Resistance Junction-to-Ambient θJA 43 °C/W DD package 2

CAD (KiCad official)

  • Symbol: LTC2485CDD#TRPBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: ltc2485cdd-trpbf-etched.step / ltc2485cdd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2485cdd-trpbf.step / ltc2485cdd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (40 pp, sha256 09382be5b68ae4d7, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF