Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LTC2485CDD#TRPBF
Analog Devices · Analog To Digital Converters (ADCs) · DFN-10-EP(3x3)
LTC2485CDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF+ | input | Positive differential reference input, which may be anywhere between GND and VCC but must be at least 0.1V more positive than REF-. |
| 2 | VCC | power_in | Positive supply voltage, specified for 2.7V to 5.5V operation and to be bypassed to GND (pin 8) with a 1µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor. |
| 3 | REF- | input | Negative differential reference input, which may be anywhere between GND and VCC and must be at least 0.1V less positive than REF+. |
| 4 | IN+ | input | Positive differential analog input, which may range from GND - 0.3V to VCC + 0.3V, with bipolar input range VIN = IN+ - IN- of -0.5 x VREF to 0.5 x VREF. |
| 5 | IN- | input | Negative differential analog input, which may range from GND - 0.3V to VCC + 0.3V, forming the differential input with IN+ over -0.5 x VREF to 0.5 x VREF. |
| 6 | SCL | input | I2C serial clock input, accepting only an external clock since the LTC2485 operates only as a slave; data is shifted into SDA on SCL rising edges and output on falling edges. |
| 7 | SDA | bidirectional | I2C bidirectional serial data line, which is an open-drain N-channel driver in data output mode and requires an external pull-up resistor or current source to VCC. |
| 8 | GND | power_in | Ground; connect to a ground plane through a low impedance connection. |
| 9 | CA1 | input | Three-state (LOW, HIGH, or Floating) chip address control pin that sets bit CA1 of the device I2C address. |
| 10 | CA0/f0 | input | Two-state (HIGH or Floating) chip address control pin for CA0 in I2C address; when driven by an external clock of at least 10kHz it becomes the system clock input with the digital filter null at fEOSC/5120. |
| 11 | GND (EP) | power_in | Exposed pad is GND and must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Data Converters |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Nonlinearity | INL | 2 | ppm of VREF | 5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V | 2 | ||
| Integral Nonlinearity | INL | 1 | ppm of VREF | 2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V | 2 | ||
| Offset Error | VOS | 0.5 | 2.5 | µV | 2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN- ≤ VCC | 2 | |
| Positive Full-Scale Error | 25 | ppm of VREF | 2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN- = 0.25VREF | 2 | |||
| Negative Full-Scale Error | 25 | ppm of VREF | 2.5V ≤ VREF ≤ VCC, IN- = 0.75VREF, IN+ = 0.25VREF | 2 | |||
| Total Unadjusted Error | 15 | ppm of VREF | 5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V | 2 | |||
| Internal PTAT Signal | VPTAT | 390 | 450 | mV | TA = 27°C | 2 | |
| Offset Error (2x Speed) | VOS | 0.5 | 2 | mV | 2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN- ≤ VCC | 3 | |
| Input Common Mode Rejection DC | CMRR | 140 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | ||
| Input Common Mode Rejection 50Hz ±2% | CMRR | 140 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | ||
| Input Common Mode Rejection 60Hz ±2% | CMRR | 140 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | ||
| Input Normal Mode Rejection 50Hz ±2% | NMRR | 110 | 120 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | |
| Input Normal Mode Rejection 60Hz ±2% | NMRR | 110 | 120 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | |
| Input Normal Mode Rejection 50Hz/60Hz ±2% | NMRR | 87 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | ||
| Reference Common Mode Rejection DC | CMRR | 120 | 140 | dB | 2.5V ≤ VREF ≤ VCC, GND ≤ IN- = IN+ ≤ VCC | 3 | |
| Power Supply Rejection DC | PSRR | 120 | dB | VREF = 2.5V, IN- = IN+ = GND | 3 | ||
| Power Supply Rejection 50Hz ±2% | PSRR | 120 | dB | VREF = 2.5V, IN- = IN+ = GND | 3 | ||
| Power Supply Rejection 60Hz ±2% | PSRR | 120 | dB | VREF = 2.5V, IN- = IN+ = GND | 3 | ||
| IN+ Absolute/Common Mode Voltage | IN+ | -0.3 | V | Max printed as VCC + 0.3V | 3 | ||
| IN- Absolute/Common Mode Voltage | IN- | -0.3 | V | Max printed as VCC + 0.3V | 3 | ||
| Reference Voltage Range (REF+, REF-) | VREF | 0.1 | V | Upper limit printed as VCC | 3 | ||
| IN+ DC Leakage Current | IDC_LEAK (IN+) | -10 | 1 | 10 | nA | Sleep mode, IN+ = GND | 4 |
| IN- DC Leakage Current | IDC_LEAK (IN-) | -10 | 1 | 10 | nA | Sleep mode, IN- = GND | 4 |
| REF+, REF- DC Leakage Current | IDC_LEAK (VREF) | -100 | 1 | 100 | nA | Sleep mode, VREF = VCC | 4 |
| Low Level Output Voltage | VOL | 0.4 | V | SDA I = 3mA | 4 | ||
| Output Fall Time from VIHMIN to VILMAX | tOF | 250 | ns | Bus Load CB 10pF to 400pF | 4 | ||
| Input Spike Suppression | tSP | 50 | ns | 4 | |||
| Input Leakage | IIN | 1 | µA | 0.1VCC ≤ VIN ≤ VCC | 4 | ||
| Capacitance for Each I/O Pin | CI | 10 | pF | 4 | |||
| Capacitance Load for Each Bus Line | CB | 400 | pF | 4 | |||
| Digital Input Current | II | -10 | 10 | µA | 4 | ||
| Low Level CA0/f0 External Oscillator Input Voltage | VIL(EXT,OSC) | 0.5 | V | 2.7V ≤ VCC < 5.5V | 4 | ||
| Supply Voltage | VCC | 2.7 | 5.5 | V | 4 | ||
| Supply Current Conversion Mode | ICC | 160 | 250 | µA | Conversion mode (internal oscillator) | 4 | |
| Supply Current Sleep Mode | ICC | 1 | 2 | µA | Sleep mode (internal oscillator) | 4 | |
| External Oscillator Frequency Range | fEOSC | 10 | 1000 | kHz | 5 | ||
| External Oscillator High Period | tHEO | 0.125 | 100 | µs | 5 | ||
| External Oscillator Low Period | tLEO | 0.125 | 100 | µs | 5 | ||
| Conversion Time 1x Speed 50Hz Mode | tCONV_1 | 157.2 | 160.3 | 163.5 | ms | Internal oscillator | 5 |
| Conversion Time 1x Speed 60Hz Mode | tCONV_1 | 131 | 133.6 | 136.3 | ms | Internal oscillator | 5 |
| Conversion Time 1x Speed Simultaneous 50Hz/60Hz Mode | tCONV_1 | 144.1 | 146.9 | 149.9 | ms | Internal oscillator | 5 |
| Conversion Time 2x Speed 50Hz Mode | tCONV_2 | 78.7 | 80.3 | 81.9 | ms | Internal oscillator | 5 |
| Conversion Time 2x Speed 60Hz Mode | tCONV_2 | 65.6 | 66.9 | 68.2 | ms | Internal oscillator | 5 |
| Conversion Time 2x Speed Simultaneous 50Hz/60Hz Mode | tCONV_2 | 72.2 | 73.6 | 75.1 | ms | Internal oscillator | 5 |
| SCL Clock Frequency | fSCL | 0 | 400 | kHz | 5 | ||
| Hold Time (Repeated) START Condition | tHD(SDA) | 0.6 | µs | 5 | |||
| LOW Period of the SCL Clock | tLOW | 1.3 | µs | 5 | |||
| HIGH Period of the SCL Clock | tHIGH | 0.6 | µs | 5 | |||
| Set-Up Time for a Repeated START Condition | tSU(STA) | 0.6 | µs | 5 | |||
| Data Hold Time | tHD(DAT) | 0 | 0.9 | µs | 5 | ||
| Data Set-Up Time | tSU(DAT) | 100 | ns | 5 | |||
| Rise Time for Both SDA and SCL Signals | tr | 300 | ns | Note 14 | 5 | ||
| Fall Time for Both SDA and SCL Signals | tf | 300 | ns | Note 14 | 5 | ||
| Set-Up Time for STOP Condition | tSU(STO) | 0.6 | µs | 5 | |||
| Supply Voltage to GND (absolute maximum) | VCC | -0.3 | 6 | V | Voltage with respect to GND | 2 | |
| Operating Temperature Range LTC2485C | TA | 0 | 70 | °C | LTC2485C grade | 2 | |
| Storage Temperature Range | TSTG | -65 | 125 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 43 | °C/W | DD package | 2 |
CAD (KiCad official)
- Symbol:
LTC2485CDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ltc2485cdd-trpbf-etched.step/ltc2485cdd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2485cdd-trpbf.step/ltc2485cdd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (40 pp, sha256
09382be5b68ae4d7, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).