Generated by kicad-footprint-generator · KiCad file format 20260206
LTC2309CF#PBF
Analog Devices · Analog To Digital Converters (ADCs) · TSSOP-20
LTC2309CF#PBF from Analog Devices, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REFCOMP | output | Reference buffer output, nominal 4.096V, bypassed to GND with 10µF and 0.1µF ceramic capacitors in parallel; the buffer is disabled by grounding VREF, allowing REFCOMP to be overdriven externally. |
| 2 | GND | power_in | Ground; all GND pins must be connected to a solid ground plane. |
| 3 | VDD | power_in | 5V supply, range 4.75V to 5.25V, bypassed to GND with a 10µF ceramic capacitor in parallel with two 0.1µF ceramic capacitors, one close to each VDD pin. |
| 4 | AD0 | input | Chip address control pin, three-state (LOW, HIGH, floating) address bit for the I2C address (see Table 2). |
| 5 | AD1 | input | Chip address control pin, three-state (LOW, HIGH, floating) address bit for the I2C address (see Table 2). |
| 6 | SCL | input | Serial clock pin of the I2C interface; the device acts only as a slave and SCL accepts only an external serial clock. |
| 7 | SDA | bidirectional | Bidirectional I2C serial data line; high impedance during data input and open-drain output during data output, requiring a pull-up device to VDD. |
| 8 | GND | power_in | Ground; all GND pins must be connected to a solid ground plane. |
| 9 | GND | power_in | Ground; all GND pins must be connected to a solid ground plane. |
| 10 | VDD | power_in | 5V supply, range 4.75V to 5.25V, bypassed to GND with a 10µF ceramic capacitor in parallel with two 0.1µF ceramic capacitors, one close to each VDD pin. |
| 11 | CH0 | input | Channel 0 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 12 | CH1 | input | Channel 1 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 13 | CH2 | input | Channel 2 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 14 | CH3 | input | Channel 3 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 15 | CH4 | input | Channel 4 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 16 | CH5 | input | Channel 5 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 17 | CH6 | input | Channel 6 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 18 | CH7 | input | Channel 7 analog input, configurable as single-ended or differential via the analog input multiplexer. |
| 19 | COM | input | Common input, the reference point for all single-ended inputs; must be noise-free and connected to ground for unipolar conversions or midway between GND and REFCOMP for bipolar conversions. |
| 20 | VREF | power_in | 2.5V reference output, bypassed to GND with a minimum 2.2µF ceramic capacitor; the internal reference may be overdriven by an external 2.5V reference at this pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSSOP-20 |
| Category | Data Converters |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resolution (No Missing Codes) | 12 | Bits | 3 | ||||
| Integral Linearity Error | INL | -1 | 0.45 | 1 | LSB | Note 6; typ printed ±0.45 | 3 |
| Differential Linearity Error | DNL | -1 | 0.35 | 1 | LSB | typ printed ±0.35 | 3 |
| Bipolar Zero Error | -8 | 1 | 8 | LSB | Note 7; typ printed ±1 | 3 | |
| Bipolar Zero Error Match | -3 | 0.1 | 3 | LSB | typ printed ±0.1 | 3 | |
| Unipolar Zero Error | -6 | 0.4 | 6 | LSB | Note 7; typ printed ±0.4 | 3 | |
| Unipolar Zero Error Match | -1 | 0.2 | 1 | LSB | typ printed ±0.2 | 3 | |
| Bipolar Full-Scale Error | -10 | 0.5 | 10 | LSB | External Reference (Note 8); typ printed ±0.5 | 3 | |
| Bipolar Full-Scale Error | -9 | 0.4 | 9 | LSB | REFCOMP = 4.096V; typ printed ±0.4 | 3 | |
| Bipolar Full-Scale Error Match | -3 | 0.4 | 3 | LSB | typ printed ±0.4 | 3 | |
| Unipolar Full-Scale Error (TSSOP) | -12 | 0.5 | 12 | LSB | TSSOP External Reference (Note 8); typ printed ±0.5 | 3 | |
| Unipolar Full-Scale Error | -6 | 0.3 | 6 | LSB | REFCOMP = 4.096V; typ printed ±0.3 | 3 | |
| Unipolar Full-Scale Error Match | -2 | 0.3 | 2 | LSB | typ printed ±0.3 | 3 | |
| Bipolar Zero Error Drift | 0.002 | LSB/°C | 3 | ||||
| Unipolar Zero Error Drift | 0.002 | LSB/°C | 3 | ||||
| Bipolar Full-Scale Error Drift | 0.05 | LSB/°C | External Reference | 3 | |||
| Unipolar Full-Scale Error Drift | 0.05 | LSB/°C | External Reference | 3 | |||
| Absolute Input Range CH0 to CH7 (min) | VIN+ | -0.05 | V | Note 9; max is REFCOMP | 3 | ||
| Analog Input Leakage Current | IIN | -1 | 1 | µA | 3 | ||
| Analog Input Capacitance, Sample Mode | CIN | 55 | pF | Sample Mode | 3 | ||
| Analog Input Capacitance, Hold Mode | CIN | 5 | pF | Hold Mode | 3 | ||
| Input Common Mode Rejection Ratio | CMRR | 70 | dB | 3 | |||
| Signal-to-(Noise + Distortion) Ratio | SINAD | 71 | 73.3 | dB | fIN = 1kHz | 3 | |
| Signal-to-Noise Ratio | SNR | 71 | 73.4 | dB | fIN = 1kHz | 3 | |
| Total Harmonic Distortion | THD | -88 | -77 | dB | fIN = 1kHz, First 5 Harmonics | 3 | |
| Spurious Free Dynamic Range | SFDR | 79 | 90 | dB | fIN = 1kHz | 3 | |
| VREF Output Voltage (TSSOP) | VREF | 2.46 | 2.5 | 2.54 | V | IOUT = 0 (TSSOP) | 4 |
| VREF Output Tempco | 25 | ppm/°C | IOUT = 0 | 4 | |||
| VREF Output Impedance | 8 | kΩ | -0.1mA ≤ IOUT ≤ 0.1mA | 4 | |||
| VREFCOMP Output Voltage | VREFCOMP | 4.096 | V | IOUT = 0 | 4 | ||
| VREF Line Regulation | 0.8 | mV/V | VDD = 4.75V to 5.25V | 4 | |||
| High Level Input Voltage | VIH | 2.85 | V | 4 | |||
| Low Level Input Voltage | VIL | 1.5 | V | 4 | |||
| High Level Input Voltage for Address Pins A1, A0 | VIHA | 4.75 | V | 4 | |||
| Low Level Input Voltage for Address Pins A1, A0 | VILA | 0.25 | V | 4 | |||
| Resistance from A1, A0 to VDD to Set Address Bit to 1 | RINH | 10 | kΩ | 4 | |||
| Resistance from A1, A0 to GND to Set Address Bit to 0 | RINL | 10 | kΩ | 4 | |||
| Resistance from A1, A0 to GND or VDD to Set Address Bit to Float | RINF | 2 | MΩ | 4 | |||
| Digital Input Current | II | -10 | 10 | µA | VIN = VDD | 4 | |
| Hysteresis of Schmitt Trigger Inputs | VHYS | 0.25 | V | Note 9 | 4 | ||
| Low Level Output Voltage (SDA) | VOL | 0.4 | V | I = 3mA | 4 | ||
| Output Fall Time | tOF | 250 | ns | VH to VIL(MAX) (Note 12); min printed 20 + 0.1CB | 4 | ||
| Input Spike Suppression | tSP | 50 | ns | 4 | |||
| External Capacitance Load On-Chip Address Pins for Valid Float | CCAX | 10 | pF | A1, A0 | 4 | ||
| Supply Voltage | VDD | 4.75 | 5 | 5.25 | V | 4 | |
| Supply Current | IDD | 2.3 | 3 | mA | 14ksps Sample Rate | 4 | |
| Supply Current, Nap Mode | IDD | 210 | 350 | µA | SLP Bit = 0, Conversion Done | 4 | |
| Supply Current, Sleep Mode | IDD | 7 | 15 | µA | SLP Bit = 1, Conversion Done | 4 | |
| Power Dissipation | PD | 11.5 | 15 | mW | 14ksps Sample Rate | 4 | |
| Power Dissipation, Nap Mode | PD | 1.05 | 1.75 | mW | SLP Bit = 0, Conversion Done | 4 | |
| Power Dissipation, Sleep Mode | PD | 35 | 75 | µW | SLP Bit = 1, Conversion Done | 4 | |
| SCL Clock Frequency | fSCL | 400 | kHz | 5 | |||
| Hold Time (Repeated) START Condition | tHD(SDA) | 0.6 | µs | 5 | |||
| LOW Period of the SCL Pin | tLOW | 1.3 | µs | 5 | |||
| HIGH Period of the SCL Pin | tHIGH | 0.6 | µs | 5 | |||
| Set-Up Time for a Repeated START Condition | tSU(STA) | 0.6 | µs | 5 | |||
| Data Hold Time | tHD(DAT) | 0 | 0.9 | µs | 5 | ||
| Data Set-Up Time | tSU(DAT) | 100 | ns | 5 | |||
| Rise Time for SDA/SCL Signals | tr | 300 | ns | Note 12; min printed 20 + 0.1CB | 5 | ||
| Fall Time for SDA/SCL Signals | tf | 300 | ns | Note 12; min printed 20 + 0.1CB | 5 | ||
| Set-Up Time for STOP Condition | tSU(STO) | 0.6 | µs | 5 | |||
| Bus Free Time Between a STOP and START Condition | tBUF | 1.3 | µs | 5 | |||
| Conversion Time | tCONV | 1.3 | 1.8 | µs | Note 9 | 5 | |
| Acquisition Time | tACQ | 240 | ns | Note 9 | 5 | ||
| Throughput Rate (Successive Reads) | fSMPL | 14 | ksps | 5 | |||
| Supply Voltage (absolute maximum) | VDD | -0.3 | 6 | V | 2 | ||
| Power Dissipation (absolute maximum) | 500 | mW | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Temperature Range LTC2309C | 0 | 70 | °C | LTC2309C | 2 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 90 | °C/W | 20-lead TSSOP | 2 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
LTC2309CF#PBF - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20, generated on the KiCad land (body 4.4 x 6.5 mm, terminals on the pads, 1.1 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ltc2309cf-etched.step/ltc2309cf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2309cf.step/ltc2309cf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
a8c486f7781eab3e, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).