main
Ray
Publish 0.1.0
c773f9c
LT8619EDD#TRPBF
Analog Devices · DC-DC Converters · TDFN-10-EP(3x3)
LT8619EDD#TRPBF from Analog Devices, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | The VIN pin supplies current to the internal circuitry and the internal topside power switch, and the input bypass capacitor should be placed as close as possible to it. |
| 2 | EN/UV | input | The part shuts down when this pin is low and is active when high, with a 1V power-on threshold and a forced-below-0.56V low-current shutdown mode. |
| 3 | RT | passive | A resistor from RT to ground sets the switching frequency, and it must not have an external voltage applied. |
| 4 | PG | output | Open-drain power good output stays low until FB is within ±7.5% of the final regulation voltage, with its pull-up tied to INTVCC, VOUT or an external supply lower than 6V. |
| 5 | SYNC | input | External clock synchronization input that forces forced continuous mode when driven, grounding it selects Burst Mode operation, and floating it selects pulse-skipping mode. |
| 6 | FB | input | The LT8619 regulates this pin to 0.8V, with the feedback divider tap connected here and a phase lead capacitor of typically 4.7pF to 10pF to VOUT, and no external voltage may be applied. |
| 7 | BIAS | power_in | The internal regulator draws current from this pin instead of VIN when it is tied above 3.1V, and for outputs of 3.3V and above it should be tied to VOUT. |
| 8 | INTVCC | power_out | Internal 3.3V regulator output that powers the internal drivers and control circuits, with a maximum output current of 20mA, decoupled with at least 1µF low ESR ceramic, and no external loading allowed. |
| 9 | BST | passive | Provides a drive voltage above the input voltage to the topside power switch, with a 0.1µF boost capacitor placed as close as possible to the IC. |
| 10 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and the node should be kept small on the PCB for good performance. |
| 11 | GND | power_in | Exposed pad ground that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TDFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN | VIN | 60 | V | 2 | |||
| EN/UV | EN/UV | 60 | V | 2 | |||
| BIAS | BIAS | 30 | V | 2 | |||
| BST Pin Above SW Pin | 4 | V | 2 | ||||
| PG | PG | 6 | V | 2 | |||
| SYNC | SYNC | 6 | V | 2 | |||
| OUT | OUT | 6 | V | 2 | |||
| FB | FB | 2 | V | 2 | |||
| Operating Junction Temperature (LT8619E) | TJ | -40 | 125 | °C | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| VIN Minimum Input Voltage | VIN | 3 | V | 3 | |||
| VIN Quiescent Current at No Load | IQ | 0.6 | 1 | µA | VIN = 12V, VEN/UV = 0V | 3 | |
| VIN Quiescent Current at No Load (full temperature range) | IQ | 0.6 | 3 | µA | VIN = 12V, VEN/UV = 0V | 3 | |
| VIN Quiescent Current in Burst Mode | IQ | 6 | 10 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V | 3 | |
| VIN Quiescent Current in Burst Mode (full temperature range) | IQ | 6 | 18 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V | 3 | |
| VIN Current in Regulation at ILOAD = 100µA | IVIN | 38 | 65 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V ILOAD = 100µA | 3 | |
| VIN Current in Regulation at ILOAD = 1mA | IVIN | 320 | 400 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V ILOAD = 1mA | 3 | |
| Feedback Voltage (25°C) | VFB | 0.796 | 0.8 | 0.804 | V | VIN = 12V, VSYNC = INTVCC, No Load | 3 |
| Feedback Voltage (full temperature range) | VFB | 0.788 | 0.8 | 0.812 | V | VIN = 12V, VSYNC = INTVCC, No Load | 3 |
| Feedback Voltage Line Regulation | -0.03 | 0.004 | 0.03 | %/V | VIN = 4V to 50V, VSYNC = INTVCC (Note 5) | 3 | |
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 0.8V | 3 | ||
| Minimum On-Time | 30 | 60 | ns | ILOAD = 0.5A, VSYNC = INTVCC | 3 | ||
| Minimum Off-Time | 100 | 150 | 180 | ns | 3 | ||
| Top Switch Peak Current Limit | 1.5 | 1.75 | 2 | A | 3 | ||
| Operating Frequency at RT = 162k | fOSC | 260 | 300 | 340 | kHz | RT = 162k | 3 |
| Operating Frequency at RT = 66.5k | fOSC | 630 | 700 | 770 | kHz | RT = 66.5k | 3 |
| Operating Frequency at RT = 20k | fOSC | 1.9 | 2 | 2.1 | MHz | RT = 20k | 3 |
| Synchronization Frequency | fSYNC | 0.3 | 2.2 | MHz | fSYNC ≥ fOSC | 3 | |
| EN/UV Power-On Threshold | 0.94 | 1 | 1.1 | V | EN/UV Rising | 4 | |
| EN/UV Shutdown Threshold | 0.34 | 0.56 | 0.92 | V | EN/UV Falling | 4 | |
| EN/UV Pin Current | -100 | 100 | nA | VEN/UV = 2V | 4 | ||
| Positive Power Good Threshold | 5 | 7.5 | 10 | % | VFB/VOUT Rising Wrt. Regulated VFB/VOUT | 4 | |
| Negative Power Good Threshold | -10 | -7.5 | -5 | % | VFB/VOUT Rising Wrt. Regulated VFB/VOUT | 4 | |
| PG Leakage | -100 | 100 | nA | VPG = 3.3V, Power Good | 4 | ||
| PG VOL | VOL | 0.01 | 0.3 | V | IPG = 100µA | 4 | |
| Operating Frequency Thermal Resistance Junction-to-Ambient (DD package) | θJA | 43 | °C/W | DD package | 2 | ||
| Thermal Resistance Junction-to-Case (DD package) | θJC | 10 | °C/W | DD package | 2 |
CAD (KiCad official)
- Symbol:
LT8619EDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt8619edd-trpbf-etched.step/lt8619edd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8619edd-trpbf.step/lt8619edd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
7156fb4077c7704f, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8619EDD#TRPBF
**Analog Devices** · DC-DC Converters · TDFN-10-EP(3x3)
LT8619EDD#TRPBF from Analog Devices, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | The VIN pin supplies current to the internal circuitry and the internal topside power switch, and the input bypass capacitor should be placed as close as possible to it. |
| 2 | EN/UV | input | The part shuts down when this pin is low and is active when high, with a 1V power-on threshold and a forced-below-0.56V low-current shutdown mode. |
| 3 | RT | passive | A resistor from RT to ground sets the switching frequency, and it must not have an external voltage applied. |
| 4 | PG | output | Open-drain power good output stays low until FB is within ±7.5% of the final regulation voltage, with its pull-up tied to INTVCC, VOUT or an external supply lower than 6V. |
| 5 | SYNC | input | External clock synchronization input that forces forced continuous mode when driven, grounding it selects Burst Mode operation, and floating it selects pulse-skipping mode. |
| 6 | FB | input | The LT8619 regulates this pin to 0.8V, with the feedback divider tap connected here and a phase lead capacitor of typically 4.7pF to 10pF to VOUT, and no external voltage may be applied. |
| 7 | BIAS | power_in | The internal regulator draws current from this pin instead of VIN when it is tied above 3.1V, and for outputs of 3.3V and above it should be tied to VOUT. |
| 8 | INTVCC | power_out | Internal 3.3V regulator output that powers the internal drivers and control circuits, with a maximum output current of 20mA, decoupled with at least 1µF low ESR ceramic, and no external loading allowed. |
| 9 | BST | passive | Provides a drive voltage above the input voltage to the topside power switch, with a 0.1µF boost capacitor placed as close as possible to the IC. |
| 10 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and the node should be kept small on the PCB for good performance. |
| 11 | GND | power_in | Exposed pad ground that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TDFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN | VIN | | | 60 | V | | 2 |
| EN/UV | EN/UV | | | 60 | V | | 2 |
| BIAS | BIAS | | | 30 | V | | 2 |
| BST Pin Above SW Pin | | | | 4 | V | | 2 |
| PG | PG | | | 6 | V | | 2 |
| SYNC | SYNC | | | 6 | V | | 2 |
| OUT | OUT | | | 6 | V | | 2 |
| FB | FB | | | 2 | V | | 2 |
| Operating Junction Temperature (LT8619E) | TJ | -40 | | 125 | °C | | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| VIN Minimum Input Voltage | VIN | 3 | | | V | | 3 |
| VIN Quiescent Current at No Load | IQ | | 0.6 | 1 | µA | VIN = 12V, VEN/UV = 0V | 3 |
| VIN Quiescent Current at No Load (full temperature range) | IQ | | 0.6 | 3 | µA | VIN = 12V, VEN/UV = 0V | 3 |
| VIN Quiescent Current in Burst Mode | IQ | | 6 | 10 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V | 3 |
| VIN Quiescent Current in Burst Mode (full temperature range) | IQ | | 6 | 18 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V | 3 |
| VIN Current in Regulation at ILOAD = 100µA | IVIN | | 38 | 65 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V ILOAD = 100µA | 3 |
| VIN Current in Regulation at ILOAD = 1mA | IVIN | | 320 | 400 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V ILOAD = 1mA | 3 |
| Feedback Voltage (25°C) | VFB | 0.796 | 0.8 | 0.804 | V | VIN = 12V, VSYNC = INTVCC, No Load | 3 |
| Feedback Voltage (full temperature range) | VFB | 0.788 | 0.8 | 0.812 | V | VIN = 12V, VSYNC = INTVCC, No Load | 3 |
| Feedback Voltage Line Regulation | | -0.03 | 0.004 | 0.03 | %/V | VIN = 4V to 50V, VSYNC = INTVCC (Note 5) | 3 |
| Feedback Pin Input Current | | -20 | | 20 | nA | VFB = 0.8V | 3 |
| Minimum On-Time | | | 30 | 60 | ns | ILOAD = 0.5A, VSYNC = INTVCC | 3 |
| Minimum Off-Time | | 100 | 150 | 180 | ns | | 3 |
| Top Switch Peak Current Limit | | 1.5 | 1.75 | 2 | A | | 3 |
| Operating Frequency at RT = 162k | fOSC | 260 | 300 | 340 | kHz | RT = 162k | 3 |
| Operating Frequency at RT = 66.5k | fOSC | 630 | 700 | 770 | kHz | RT = 66.5k | 3 |
| Operating Frequency at RT = 20k | fOSC | 1.9 | 2 | 2.1 | MHz | RT = 20k | 3 |
| Synchronization Frequency | fSYNC | 0.3 | | 2.2 | MHz | fSYNC ≥ fOSC | 3 |
| EN/UV Power-On Threshold | | 0.94 | 1 | 1.1 | V | EN/UV Rising | 4 |
| EN/UV Shutdown Threshold | | 0.34 | 0.56 | 0.92 | V | EN/UV Falling | 4 |
| EN/UV Pin Current | | -100 | | 100 | nA | VEN/UV = 2V | 4 |
| Positive Power Good Threshold | | 5 | 7.5 | 10 | % | VFB/VOUT Rising Wrt. Regulated VFB/VOUT | 4 |
| Negative Power Good Threshold | | -10 | -7.5 | -5 | % | VFB/VOUT Rising Wrt. Regulated VFB/VOUT | 4 |
| PG Leakage | | -100 | | 100 | nA | VPG = 3.3V, Power Good | 4 |
| PG VOL | VOL | | 0.01 | 0.3 | V | IPG = 100µA | 4 |
| Operating Frequency Thermal Resistance Junction-to-Ambient (DD package) | θJA | | 43 | | °C/W | DD package | 2 |
| Thermal Resistance Junction-to-Case (DD package) | θJC | | 10 | | °C/W | DD package | 2 |
## CAD (KiCad official)
- Symbol: `LT8619EDD#TRPBF`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `lt8619edd-trpbf-etched.step` / `lt8619edd-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8619edd-trpbf.step` / `lt8619edd-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LT8619-8619-5.pdf) (28 pp, sha256 `7156fb4077c7704f`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8619edd-trpbf-datasheet.pdf)