main
Ray
Publish 0.1.0
eea67b9
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230
{
"slug": "lt8618cav",
"version": "0.1.0",
"type": "component",
"description": "Analog Devices Inc. AC-DC Controllers & Regulators, LQFN-12(2x2). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
"tags": [
"component",
"power management ics",
"lt8618cav#trpbf",
"factory-2.0.0",
"extractor-text"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"lt8618cav.kicad_sym",
"lt8618cav.kicad_mod",
"lt8618cav.glb",
"lt8618cav.step",
"lt8618cav.lbr",
"docs/hero.png",
"docs/lt8618cav-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"lt8618cav-hero.glb",
"lt8618cav-hero.overlay.json"
],
"component": {
"mpn": "LT8618CAV",
"manufacturer": "Analog Devices Inc.",
"package": "LQFN-12(2x2)",
"pin_count": 13,
"category": "Power Management ICs",
"subcategory": "AC-DC Controllers & Regulators",
"datasheet": "https://www.analog.com/media/en/technical-documentation/data-sheets/lt8618-8618-3_3.pdf",
"parts": {
"symbol": "lt8618cav.kicad_sym",
"footprint": "lt8618cav.kicad_mod",
"model_3d": "lt8618cav-hero.glb",
"model_3d_plain": "lt8618cav.glb",
"model_3d_step": "lt8618cav-etched.step",
"model_3d_step_plain": "lt8618cav.step",
"lbr": "lt8618cav.lbr"
},
"distributor_links": {
"lcsc": "C3187780",
"digikey": "505-LT8618CAV#TRPBFTR-ND",
"mouser": "584-LT8618CAVTRPBF"
},
"distributor_check": {
"checked_at": "2026-11-12T22:28:21Z",
"source": "Component Ocean /api/assign-pns",
"digikey": {
"pn": "505-LT8618CAV#TRPBFTR-ND",
"status": "found"
},
"mouser": {
"pn": "584-LT8618CAVTRPBF",
"status": "found"
}
},
"pins": [
{
"number": "1",
"name": "VIN",
"type": "power_in",
"description": "Supplies current to the LT8618C internal circuitry and the internal top-side power switch; operating input is 3.4V to 60V with 65V maximum for transients, and the input capacitor positive terminal should be placed as close as possible to this pin."
},
{
"number": "2",
"name": "EN/UV",
"type": "input",
"description": "Enable pin: the LT8618C is shut down when low and active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it can be tied to VIN if shutdown is not used."
},
{
"number": "3",
"name": "HYST",
"type": "output",
"description": "Open-drain EN/UV hysteresis logic output that is pulled to ground when EN/UV is below 1V, used to adjust EN/UV pin hysteresis; absolute maximum voltage is 12V."
},
{
"number": "4",
"name": "PG",
"type": "output",
"description": "Open-drain power-good output that stays low until FB is within ±7.5% of the final regulation voltage with no fault conditions, is valid when VIN is above 3.4V, and has a 42V maximum voltage rating."
},
{
"number": "5",
"name": "FB",
"type": "input",
"description": "Feedback pin that the LT8618C regulates to 0.778V; the feedback resistor divider tap connects here, with an absolute maximum voltage of 4V."
},
{
"number": "6",
"name": "TR/SS",
"type": "bidirectional",
"description": "Output tracking and soft-start pin: a voltage below 0.778V forces FB to follow TR/SS, an internal 2µA pull-up sets the soft-start slew rate, and a 300Ω pull-down acts during shutdown and faults, so use a series resistor when driven from a low-impedance source; absolute maximum voltage is 4V."
},
{
"number": "7",
"name": "SYNC/MODE",
"type": "input",
"description": "Mode-select pin: tie low for Burst Mode operation, float for forced continuous mode (leakage below 1µA), tie above 3V for spread-spectrum mode, or drive with a clock (valleys below 0.4V, peaks above 1.5V up to 6V) to synchronize over 200kHz to 2.2MHz."
},
{
"number": "8",
"name": "RT",
"type": "passive",
"description": "Tie a resistor between this pin and ground to set the switching frequency over the 200kHz to 2.2MHz range."
},
{
"number": "9",
"name": "BIAS",
"type": "power_in",
"description": "Supplies the internal regulator when tied above 3.2V; for output voltages of 3.3V to 25V it should be tied to VOUT, a 1µF local bypass is required if another supply is used, and it should be tied to GND if no supply is available."
},
{
"number": "10",
"name": "SW",
"type": "output",
"description": "Output of the internal power switches that connects to the inductor; this node should be kept small on the PCB for good performance."
},
{
"number": "11",
"name": "DNC",
"type": "unconnected",
"description": "Do not connect; this pin must be left floating."
},
{
"number": "12",
"name": "GND",
"type": "power_in",
"description": "Ground pin that should be connected to the input capacitor negative terminal, placed as close as possible to the VIN capacitor."
},
{
"number": "13",
"name": "GND",
"type": "power_in",
"description": "Exposed pad ground that must be connected to the input capacitor negative terminal and soldered to the PCB to lower thermal resistance."
}
],
"provenance": {
"extractor": "extract_pins 0.3",
"factory_chain": {
"factory": "2.0.0",
"extractor": "extract_pins 0.3",
"primary_model": "claude-haiku-5-5",
"primary_mode": "text",
"consensus_model": "claude-sonnet-5-5",
"consensus": "agreed",
"guards": "pin_guards 0.1: passed",
"guard_notes": [
"extractor flagged: The LQFN top-view pin layout on page 2 is garbled in the text extraction, so pin numbers were mapped; Pin types are KiCad ERC approximations: HYST, PG and SW are open-drain or power-switch outputs mappe; The datasheet lists the LQFN pin 13 as the exposed pad and pin 12 as GND, and both are included as G"
],
"pages_sent": 29,
"cost_usd": 0.1778,
"at": "2026-11-12T22:27:57"
},
"datasheet": {
"url": "https://www.analog.com/media/en/technical-documentation/data-sheets/lt8618-8618-3_3.pdf",
"pages": 29,
"sha256": "4bd6ffbba1021846",
"source_tier": "mfr"
},
"cad": "KiCad official (CC-BY-SA 4.0)",
"model_3d_generated": {
"generator": "factory/gen_pkg3d.py",
"family": "QFN",
"height_mm": 0.9,
"height_basis": "family nominal (no datasheet A read)",
"standoff_mm": 0.0
},
"pins": {
"total": 13,
"described": 13,
"cites_pages": true,
"refuses_to_fabricate": true
}
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"models_3d": [
{
"file": "lt8618cav.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
2.02,
2.02,
0.9
],
"zmin_mm": 0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "d2fb9bc6d3a70f0e5304f03eadc84486293c826ef2e9b968bd2bc76941051120",
"checked": "2026-11-12",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "lt8618cav-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
2.02,
2.02,
0.9
],
"zmin_mm": 0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "d20098c7373c28adc1eeb7596d3af9c84639aff95cbf44e15e4d8e0e28101dd3",
"checked": "2026-11-12",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
]
}
}