main
Ray Publish 0.1.0 5965e5c

LT8613IUDE#TRPBF

Analog Devices · DC-DC Converters · QFN-28-EP(3x6)

LT8613IUDE#TRPBF from Analog Devices, in a QFN-28-EP(3x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC input External clock synchronization input; ground for low ripple Burst Mode operation, tie to a clock for synchronization, or apply DC of 3V or higher or tie to INTVCC for pulse-skipping mode; do not float.
2 TR/SS input Output tracking and soft-start pin; a capacitor programs output ramp rate using an internal 2.2µA pull-up, regulates FB to TR/SS below 0.97V, and is pulled down by an internal 230Ω MOSFET in shutdown and fault; may float if unused.
3 RT passive A resistor tied between RT and ground sets the switching frequency.
4 EN/UV input Shuts down the part when low and enables when high, with hysteretic threshold of 1.00V rising and 0.96V falling; tie to VIN if unused or use a resistor divider from VIN to program undervoltage lockout.
5 VIN power_in Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by.
6 VIN power_in Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by.
7 VIN power_in Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by.
8 PGND power_in Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 9 and 10 and placed close to the input capacitor negative terminal.
9 PGND power_in Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 8 and 10 and placed close to the input capacitor negative terminal.
10 PGND power_in Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 8 and 9 and placed close to the input capacitor negative terminal.
11 GND power_in Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance.
12 GND power_in Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance.
13 GND power_in Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance.
14 GND power_in Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance.
15 SW power_out Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB.
16 SW power_out Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB.
17 SW power_out Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB.
18 SW power_out Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB.
19 SW power_out Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB.
20 BST passive Provides drive voltage higher than the input voltage to the topside switch; place a 0.1µF boost capacitor as close as possible to the IC (max 4V above SW).
21 INTVCC power_out Internal 3.4V regulator bypass pin with 20mA maximum output current; do not load externally and decouple with at least 1µF low ESR ceramic close to the IC.
22 BIAS power_in Internal regulator draws current from BIAS instead of VIN when above 3.1V; tie to VOUT for outputs of 3.3V and above, otherwise use a 1µF local bypass capacitor (25V max).
23 PG output Open-drain power-good output that stays low until FB is within ±9% of final regulation voltage with no faults; valid when VIN is above 3.4V regardless of EN/UV state.
24 FB input Regulated to 0.970V; connect the feedback resistor divider tap here and a 4.7pF to 10pF phase lead capacitor between FB and VOUT.
25 ISP input Current sense (+) pin, the noninverting input to the current sense amplifier.
26 ISN input Current sense (-) pin, the inverting input to the current sense amplifier.
27 IMON output Current monitor output sourcing a voltage of 20 × (VISP-VISN), able to source 200µA and sink 10µA; float if unused.
28 ICTRL input Current adjustment pin; connect to INTVCC or float for the full-scale 50mV ISP-ISN threshold, or apply 0 to 1V to modulate the limit, with an internal 1.4µA pull-up.
29 GND power_in Exposed pad ground; must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-28-EP(3x6)
Category Power Supply Chip
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, EN/UV, PG, ISP, ISN Voltage 42 V 2
BIAS Voltage 25 V 2
BST Pin Above SW Pin 4 V 2
FB, TR/SS, RT, INTVCC, IMON, ICTRL Voltage 4 V 2
SYNC Voltage 6 V 2
Operating Junction Temperature Range (LT8613I) -40 125 °C LT8613I 2
Storage Temperature Range -65 150 °C 2
Junction-to-Ambient Thermal Resistance θJA 40 °C/W UDE package 2
Junction-to-Case (Pad) Thermal Resistance θJC(PAD) 5 °C/W UDE package 2
VIN Quiescent Current IQ 1 5 µA VEN/UV = 0V, VSYNC = 0V 2
VIN Quiescent Current (full temp) IQ 1 20 µA VEN/UV = 0V, VSYNC = 0V, over full temperature range 2
VIN Quiescent Current, not switching IQ 1.7 6 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 2
VIN Quiescent Current, not switching (full temp) IQ 1.7 20 µA VEN/UV = 2V, Not Switching, VSYNC = 0V, over full temperature range 2
VIN Quiescent Current, SYNC high IQ 0.3 2 mA VEN/UV = 2V, Not Switching, VSYNC = 2V 2
Feedback Reference Voltage VFB 0.964 0.97 0.976 V VIN = 12V, ILOAD = 500mA 2
Feedback Reference Voltage (full temp) VFB 0.958 0.97 0.982 V VIN = 12V, ILOAD = 500mA, over full temperature range 2
Feedback Voltage Line Regulation 0.004 0.025 %/V VIN = 4.0V to 25V, ILOAD = 0.5A 2
Feedback Pin Input Current -20 0.5 20 nA VFB = 1V 2
Minimum On-Time (SYNC = 0V) tON(MIN) 20 40 60 ns ILOAD = 2A, SYNC = 0V 3
Minimum On-Time (SYNC = 3.3V) tON(MIN) 20 35 55 ns ILOAD = 2A, SYNC = 3.3V 3
Minimum Off-Time tOFF(MIN) 50 85 120 ns 3
Oscillator Frequency fSW 180 210 240 kHz RT = 221k, ILOAD = 1.5A 3
Oscillator Frequency fSW 665 700 735 kHz RT = 60.4k, ILOAD = 1.5A 3
Oscillator Frequency fSW 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 1.5A 3
Top Power NMOS Current Limit 7.5 9.7 12 A 3
Valley Current Limit 6 10 12 A VINTVCC = 3.4V 3
SW Leakage Current -10 0.1 10 µA VIN = 42V, VSW = 0V, 42V 3
EN/UV Pin Threshold 0.94 1 1.06 V EN/UV Rising 3
EN/UV Pin Current -20 1 20 nA VEN/UV = 2V 3
PG Upper Threshold Offset from VFB 6.5 9 11.5 % VFB Falling 3
PG Lower Threshold Offset from VFB -11.5 -9 -6.5 % VFB Rising 3
PG Leakage -40 40 nA VPG = 3.3V 3
PG Pull-Down Resistance 680 2000 Ω VPG = 0.1V 3
SYNC Threshold Falling 0.7 1 1.4 V SYNC Falling 3
SYNC Threshold Rising 1 1.3 1.55 V SYNC Rising 3
SYNC Pin Current -100 100 nA VSYNC = 2V 3
TR/SS Source Current 1.4 2.1 2.7 µA 3
Current Sense Voltage (VISP-ISN) 48 50 52 mV VICTRL = 1.5V, VISN = 3.3V 3
Current Sense Voltage (VISP-ISN) 46 50.5 56 mV VICTRL = 1.5V, VISN = 0V 3
Current Sense Voltage (VISP-ISN) 38 41 46 mV VICTRL = 800mV, VISN = 3.3V 3
Current Sense Voltage (VISP-ISN) 37 42 47 mV VICTRL = 800mV, VISN = 0V 3
Current Sense Voltage (VISP-ISN) 5 10 15 mV VICTRL = 200mV, VISN = 3.3V 3
Current Sense Voltage (VISP-ISN) 4 10.5 17 mV VICTRL = 200mV, VISN = 0V 3
IMON Monitor Pin Voltage 0.96 1 1.04 V VISP-ISN = 50mV, VISN = 3.3V 3
IMON Monitor Pin Voltage 0.89 0.99 1.09 V VISP-ISN = 50mV, VISN = 0V 3
IMON Monitor Pin Voltage 130 220 320 mV VISP-ISN = 10mV, VISN = 3.3V 3
IMON Monitor Pin Voltage 110 205 300 mV VISP-ISN = 10mV, VISN = 0V 3
ISP, ISN Pin Bias Current -20 20 µA 3
VIN Current in Regulation 24 60 µA VOUT = 0.97V, VIN = 6V, Output Load = 100µA 2
VIN Current in Regulation 230 370 µA VOUT = 0.97V, VIN = 6V, Output Load = 1mA 2
BIAS Pin Current Consumption 14 mA VBIAS = 3.3V, ILOAD = 2A, 2MHz 2
Top Power NMOS On-Resistance 65 mΩ ISW = 1A 3
Bottom Power NMOS On-Resistance 29 mΩ VINTVCC = 3.4V, ISW = 1A 3
EN/UV Pin Hysteresis 40 mV 3
PG Hysteresis 1.3 % 3
TR/SS Pull-Down Resistance 230 Ω Fault Condition, TR/SS = 0.1V 3

CAD (KiCad official)

  • Symbol: LT8613IUDE#TRPBF
  • Footprint: Package_DFN_QFN:QFN-28-1EP_3x6mm_P0.5mm_EP1.7x4.75mm
  • 3D model: QFN-28-EP(3x6) (KiCad packages3D, STEP)
  • 3D model files: lt8613iude-trpbf-etched.step / lt8613iude-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8613iude-trpbf.step / lt8613iude-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 8a698959d481813c, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF