3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8613IUDE#TRPBF
Analog Devices · DC-DC Converters · QFN-28-EP(3x6)
LT8613IUDE#TRPBF from Analog Devices, in a QFN-28-EP(3x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input; ground for low ripple Burst Mode operation, tie to a clock for synchronization, or apply DC of 3V or higher or tie to INTVCC for pulse-skipping mode; do not float. |
| 2 | TR/SS | input | Output tracking and soft-start pin; a capacitor programs output ramp rate using an internal 2.2µA pull-up, regulates FB to TR/SS below 0.97V, and is pulled down by an internal 230Ω MOSFET in shutdown and fault; may float if unused. |
| 3 | RT | passive | A resistor tied between RT and ground sets the switching frequency. |
| 4 | EN/UV | input | Shuts down the part when low and enables when high, with hysteretic threshold of 1.00V rising and 0.96V falling; tie to VIN if unused or use a resistor divider from VIN to program undervoltage lockout. |
| 5 | VIN | power_in | Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by. |
| 6 | VIN | power_in | Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by. |
| 7 | VIN | power_in | Supplies the internal circuitry and the topside power switch; pins 5, 6, 7 must be tied together and locally bypassed with the input capacitor close by. |
| 8 | PGND | power_in | Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 9 and 10 and placed close to the input capacitor negative terminal. |
| 9 | PGND | power_in | Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 8 and 10 and placed close to the input capacitor negative terminal. |
| 10 | PGND | power_in | Power switch ground, return path of the internal bottom-side switch; must be tied together with pins 8 and 9 and placed close to the input capacitor negative terminal. |
| 11 | GND | power_in | Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance. |
| 12 | GND | power_in | Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance. |
| 13 | GND | power_in | Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance. |
| 14 | GND | power_in | Recommended to be connected to GND so the exposed pad GND can be run to top-level GND copper to enhance thermal performance. |
| 15 | SW | power_out | Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB. |
| 16 | SW | power_out | Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB. |
| 17 | SW | power_out | Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB. |
| 18 | SW | power_out | Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB. |
| 19 | SW | power_out | Output of the internal power switches; tie pins 15-19 together to the inductor and boost capacitor and keep the node small on the PCB. |
| 20 | BST | passive | Provides drive voltage higher than the input voltage to the topside switch; place a 0.1µF boost capacitor as close as possible to the IC (max 4V above SW). |
| 21 | INTVCC | power_out | Internal 3.4V regulator bypass pin with 20mA maximum output current; do not load externally and decouple with at least 1µF low ESR ceramic close to the IC. |
| 22 | BIAS | power_in | Internal regulator draws current from BIAS instead of VIN when above 3.1V; tie to VOUT for outputs of 3.3V and above, otherwise use a 1µF local bypass capacitor (25V max). |
| 23 | PG | output | Open-drain power-good output that stays low until FB is within ±9% of final regulation voltage with no faults; valid when VIN is above 3.4V regardless of EN/UV state. |
| 24 | FB | input | Regulated to 0.970V; connect the feedback resistor divider tap here and a 4.7pF to 10pF phase lead capacitor between FB and VOUT. |
| 25 | ISP | input | Current sense (+) pin, the noninverting input to the current sense amplifier. |
| 26 | ISN | input | Current sense (-) pin, the inverting input to the current sense amplifier. |
| 27 | IMON | output | Current monitor output sourcing a voltage of 20 × (VISP-VISN), able to source 200µA and sink 10µA; float if unused. |
| 28 | ICTRL | input | Current adjustment pin; connect to INTVCC or float for the full-scale 50mV ISP-ISN threshold, or apply 0 to 1V to modulate the limit, with an internal 1.4µA pull-up. |
| 29 | GND | power_in | Exposed pad ground; must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(3x6) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN/UV, PG, ISP, ISN Voltage | 42 | V | 2 | ||||
| BIAS Voltage | 25 | V | 2 | ||||
| BST Pin Above SW Pin | 4 | V | 2 | ||||
| FB, TR/SS, RT, INTVCC, IMON, ICTRL Voltage | 4 | V | 2 | ||||
| SYNC Voltage | 6 | V | 2 | ||||
| Operating Junction Temperature Range (LT8613I) | -40 | 125 | °C | LT8613I | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 40 | °C/W | UDE package | 2 | ||
| Junction-to-Case (Pad) Thermal Resistance | θJC(PAD) | 5 | °C/W | UDE package | 2 | ||
| VIN Quiescent Current | IQ | 1 | 5 | µA | VEN/UV = 0V, VSYNC = 0V | 2 | |
| VIN Quiescent Current (full temp) | IQ | 1 | 20 | µA | VEN/UV = 0V, VSYNC = 0V, over full temperature range | 2 | |
| VIN Quiescent Current, not switching | IQ | 1.7 | 6 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 2 | |
| VIN Quiescent Current, not switching (full temp) | IQ | 1.7 | 20 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V, over full temperature range | 2 | |
| VIN Quiescent Current, SYNC high | IQ | 0.3 | 2 | mA | VEN/UV = 2V, Not Switching, VSYNC = 2V | 2 | |
| Feedback Reference Voltage | VFB | 0.964 | 0.97 | 0.976 | V | VIN = 12V, ILOAD = 500mA | 2 |
| Feedback Reference Voltage (full temp) | VFB | 0.958 | 0.97 | 0.982 | V | VIN = 12V, ILOAD = 500mA, over full temperature range | 2 |
| Feedback Voltage Line Regulation | 0.004 | 0.025 | %/V | VIN = 4.0V to 25V, ILOAD = 0.5A | 2 | ||
| Feedback Pin Input Current | -20 | 0.5 | 20 | nA | VFB = 1V | 2 | |
| Minimum On-Time (SYNC = 0V) | tON(MIN) | 20 | 40 | 60 | ns | ILOAD = 2A, SYNC = 0V | 3 |
| Minimum On-Time (SYNC = 3.3V) | tON(MIN) | 20 | 35 | 55 | ns | ILOAD = 2A, SYNC = 3.3V | 3 |
| Minimum Off-Time | tOFF(MIN) | 50 | 85 | 120 | ns | 3 | |
| Oscillator Frequency | fSW | 180 | 210 | 240 | kHz | RT = 221k, ILOAD = 1.5A | 3 |
| Oscillator Frequency | fSW | 665 | 700 | 735 | kHz | RT = 60.4k, ILOAD = 1.5A | 3 |
| Oscillator Frequency | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1.5A | 3 |
| Top Power NMOS Current Limit | 7.5 | 9.7 | 12 | A | 3 | ||
| Valley Current Limit | 6 | 10 | 12 | A | VINTVCC = 3.4V | 3 | |
| SW Leakage Current | -10 | 0.1 | 10 | µA | VIN = 42V, VSW = 0V, 42V | 3 | |
| EN/UV Pin Threshold | 0.94 | 1 | 1.06 | V | EN/UV Rising | 3 | |
| EN/UV Pin Current | -20 | 1 | 20 | nA | VEN/UV = 2V | 3 | |
| PG Upper Threshold Offset from VFB | 6.5 | 9 | 11.5 | % | VFB Falling | 3 | |
| PG Lower Threshold Offset from VFB | -11.5 | -9 | -6.5 | % | VFB Rising | 3 | |
| PG Leakage | -40 | 40 | nA | VPG = 3.3V | 3 | ||
| PG Pull-Down Resistance | 680 | 2000 | Ω | VPG = 0.1V | 3 | ||
| SYNC Threshold Falling | 0.7 | 1 | 1.4 | V | SYNC Falling | 3 | |
| SYNC Threshold Rising | 1 | 1.3 | 1.55 | V | SYNC Rising | 3 | |
| SYNC Pin Current | -100 | 100 | nA | VSYNC = 2V | 3 | ||
| TR/SS Source Current | 1.4 | 2.1 | 2.7 | µA | 3 | ||
| Current Sense Voltage (VISP-ISN) | 48 | 50 | 52 | mV | VICTRL = 1.5V, VISN = 3.3V | 3 | |
| Current Sense Voltage (VISP-ISN) | 46 | 50.5 | 56 | mV | VICTRL = 1.5V, VISN = 0V | 3 | |
| Current Sense Voltage (VISP-ISN) | 38 | 41 | 46 | mV | VICTRL = 800mV, VISN = 3.3V | 3 | |
| Current Sense Voltage (VISP-ISN) | 37 | 42 | 47 | mV | VICTRL = 800mV, VISN = 0V | 3 | |
| Current Sense Voltage (VISP-ISN) | 5 | 10 | 15 | mV | VICTRL = 200mV, VISN = 3.3V | 3 | |
| Current Sense Voltage (VISP-ISN) | 4 | 10.5 | 17 | mV | VICTRL = 200mV, VISN = 0V | 3 | |
| IMON Monitor Pin Voltage | 0.96 | 1 | 1.04 | V | VISP-ISN = 50mV, VISN = 3.3V | 3 | |
| IMON Monitor Pin Voltage | 0.89 | 0.99 | 1.09 | V | VISP-ISN = 50mV, VISN = 0V | 3 | |
| IMON Monitor Pin Voltage | 130 | 220 | 320 | mV | VISP-ISN = 10mV, VISN = 3.3V | 3 | |
| IMON Monitor Pin Voltage | 110 | 205 | 300 | mV | VISP-ISN = 10mV, VISN = 0V | 3 | |
| ISP, ISN Pin Bias Current | -20 | 20 | µA | 3 | |||
| VIN Current in Regulation | 24 | 60 | µA | VOUT = 0.97V, VIN = 6V, Output Load = 100µA | 2 | ||
| VIN Current in Regulation | 230 | 370 | µA | VOUT = 0.97V, VIN = 6V, Output Load = 1mA | 2 | ||
| BIAS Pin Current Consumption | 14 | mA | VBIAS = 3.3V, ILOAD = 2A, 2MHz | 2 | |||
| Top Power NMOS On-Resistance | 65 | mΩ | ISW = 1A | 3 | |||
| Bottom Power NMOS On-Resistance | 29 | mΩ | VINTVCC = 3.4V, ISW = 1A | 3 | |||
| EN/UV Pin Hysteresis | 40 | mV | 3 | ||||
| PG Hysteresis | 1.3 | % | 3 | ||||
| TR/SS Pull-Down Resistance | 230 | Ω | Fault Condition, TR/SS = 0.1V | 3 |
CAD (KiCad official)
- Symbol:
LT8613IUDE#TRPBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_3x6mm_P0.5mm_EP1.7x4.75mm - 3D model: QFN-28-EP(3x6) (KiCad packages3D, STEP)
- 3D model files:
lt8613iude-trpbf-etched.step/lt8613iude-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8613iude-trpbf.step/lt8613iude-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
8a698959d481813c, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).