main
Ray
Publish 0.1.0
5ee9147
LT8610AEMSE#TRPBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8610AEMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input that must not float: ground it for low-ripple Burst Mode at light load, tie to a clock for synchronization, or apply 3V or higher or tie to INTVCC for pulse-skipping mode. |
| 2 | TR/SS | passive | Output tracking and soft-start pin where a voltage below 0.97V forces FB to follow it, and an internal 2.2µA pull-up from INTVCC with an external capacitor sets the output ramp rate. |
| 3 | RT | passive | A resistor from RT to ground sets the switching frequency, specified over 200kHz to 2.2MHz. |
| 4 | EN/UV | input | The part is shut down when this pin is low and enabled when high, with a hysteretic threshold of 1.00V rising and 0.96V falling; tie to VIN if unused. |
| 5 | VIN | power_in | Input supply pin for internal circuitry and the topside power switch, which must be tied together with pin 6 and locally bypassed; the input range is 3.4V to 42V. |
| 6 | VIN | power_in | Input supply pin for internal circuitry and the topside power switch, which must be tied together with pin 5 and locally bypassed; the input range is 3.4V to 42V. |
| 7 | NC | unconnected | No connect pin that is not connected to internal circuitry. |
| 8 | GND | power_in | Ground return for the internal bottom-side switch, which must be tied together with the exposed pad (pin 17). |
| 9 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 10 and 11 and connected to the inductor and boost capacitor. |
| 10 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor. |
| 11 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor. |
| 12 | BST | passive | Provides a drive voltage above the input voltage to the topside power switch, using a 0.1µF boost capacitor placed as close as possible to the IC. |
| 13 | INTVCC | power_out | Internal 3.4V regulator bypass pin with a maximum output current of 20mA, decoupled to power ground with at least 1µF low ESR ceramic and not to be loaded externally. |
| 14 | BIAS | power_in | Supplies the internal regulator from BIAS instead of VIN when tied above 3.1V, and should be tied to VOUT for output voltages of 3.3V and above. |
| 15 | PG | output | Open-drain power-good output that remains low until FB is within ±9% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.4V. |
| 16 | FB | input | Feedback input that the part regulates to 0.970V on adjustable versions, where the feedback resistor divider tap connects and a phase lead capacitor of 4.7pF to 10pF goes to VOUT. |
| 17 | GND | power_in | Exposed pad ground that must be soldered to the PCB to lower the thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Reference Voltage (25°C row) | VFB | 0.964 | 0.97 | 0.976 | V | VIN = 6V, ILOAD = 0.5A | 3 |
| Feedback Reference Voltage (full operating temperature range) | VFB | 0.958 | 0.97 | 0.982 | V | VIN = 6V, ILOAD = 0.5A (l: full operating temperature range) | 3 |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4V to 42V, ILOAD = 1A (l: full operating temperature range) | 3 | ||
| Feedback Pin Input Current | IFB | -20 | 20 | nA | VFB = 1V | 3 | |
| Minimum On-Time | tON(MIN) | 15 | 30 | 45 | ns | ILOAD = 1A, SYNC = 0V (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 180 | 210 | 240 | kHz | RT = 221k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 665 | 700 | 735 | kHz | RT = 60.4k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Top Power NMOS Current Limit (LT8610A) | ILIM | 5 | 6.7 | 8 | A | LT8610A (l: full operating temperature range) | 4 |
| Bottom Power NMOS Current Limit | ILIM | 3.4 | 4.3 | 5.4 | A | VINTVCC = 3.4V | 4 |
| SW Leakage Current | ISW | -1.5 | 1.5 | µA | VIN = 42V, VSW = 0V, 42V | 4 | |
| INTVCC Undervoltage Lockout | VINTVCC(UVLO) | 2.5 | 2.6 | 2.7 | V | 4 | |
| EN/UV Pin Threshold | VEN/UV | 0.94 | 1 | 1.06 | V | EN/UV Rising (l: full operating temperature range) | 4 |
| EN/UV Pin Current | IEN/UV | -20 | 20 | nA | VEN/UV = 2V | 4 | |
| PG Upper Threshold Offset from VFB | 6 | 9 | 12 | % | VFB Falling (l: full operating temperature range) | 4 | |
| PG Lower Threshold Offset from VFB | -12 | -9 | -6 | % | VFB Rising (l: full operating temperature range) | 4 | |
| PG Leakage | IPG | -40 | 40 | nA | VPG = 3.3V | 4 | |
| SYNC Threshold (falling) | VSYNC | 0.8 | 1.1 | 1.4 | V | SYNC Falling | 4 |
| SYNC Threshold (rising) | VSYNC | 1.6 | 2 | 2.4 | V | SYNC Rising | 4 |
| SYNC Pin Current | ISYNC | -40 | 40 | nA | VSYNC = 6V | 4 | |
| TR/SS Source Current | ITR/SS | 1 | 2 | 3.2 | µA | (l: full operating temperature range) | 4 |
| Operating Junction Temperature Range (LT8610AE) | TJ | -40 | 125 | °C | LT8610AE/LT8610ABE (Note 2) | 2 | |
| VIN, EN/UV, PG Voltage | VIN | 42 | V | 2 | |||
| BST Pin Above SW Pin | VBST-SW | 4 | V | 2 | |||
| FB, TR/SS, RT, INTVCC Voltage | 4 | V | 2 | ||||
| VOUT, SYNC Voltage | VOUT, VSYNC | 6 | V | 2 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance, Junction to Ambient | θJA | 40 | °C/W | 2 | |||
| Thermal Resistance, Junction to Exposed Pad | θJC(PAD) | 10 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT8610AEMSE#TRPBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8610aemse-trpbf-etched.step/lt8610aemse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8610aemse-trpbf.step/lt8610aemse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
b37433c4b3415525, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8610AEMSE#TRPBF
**Analog Devices** · DC-DC Converters · MSOP-16-EP
LT8610AEMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input that must not float: ground it for low-ripple Burst Mode at light load, tie to a clock for synchronization, or apply 3V or higher or tie to INTVCC for pulse-skipping mode. |
| 2 | TR/SS | passive | Output tracking and soft-start pin where a voltage below 0.97V forces FB to follow it, and an internal 2.2µA pull-up from INTVCC with an external capacitor sets the output ramp rate. |
| 3 | RT | passive | A resistor from RT to ground sets the switching frequency, specified over 200kHz to 2.2MHz. |
| 4 | EN/UV | input | The part is shut down when this pin is low and enabled when high, with a hysteretic threshold of 1.00V rising and 0.96V falling; tie to VIN if unused. |
| 5 | VIN | power_in | Input supply pin for internal circuitry and the topside power switch, which must be tied together with pin 6 and locally bypassed; the input range is 3.4V to 42V. |
| 6 | VIN | power_in | Input supply pin for internal circuitry and the topside power switch, which must be tied together with pin 5 and locally bypassed; the input range is 3.4V to 42V. |
| 7 | NC | unconnected | No connect pin that is not connected to internal circuitry. |
| 8 | GND | power_in | Ground return for the internal bottom-side switch, which must be tied together with the exposed pad (pin 17). |
| 9 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 10 and 11 and connected to the inductor and boost capacitor. |
| 10 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor. |
| 11 | SW | output | Switch node output of the internal power switches, which must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor. |
| 12 | BST | passive | Provides a drive voltage above the input voltage to the topside power switch, using a 0.1µF boost capacitor placed as close as possible to the IC. |
| 13 | INTVCC | power_out | Internal 3.4V regulator bypass pin with a maximum output current of 20mA, decoupled to power ground with at least 1µF low ESR ceramic and not to be loaded externally. |
| 14 | BIAS | power_in | Supplies the internal regulator from BIAS instead of VIN when tied above 3.1V, and should be tied to VOUT for output voltages of 3.3V and above. |
| 15 | PG | output | Open-drain power-good output that remains low until FB is within ±9% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.4V. |
| 16 | FB | input | Feedback input that the part regulates to 0.970V on adjustable versions, where the feedback resistor divider tap connects and a phase lead capacitor of 4.7pF to 10pF goes to VOUT. |
| 17 | GND | power_in | Exposed pad ground that must be soldered to the PCB to lower the thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Reference Voltage (25°C row) | VFB | 0.964 | 0.97 | 0.976 | V | VIN = 6V, ILOAD = 0.5A | 3 |
| Feedback Reference Voltage (full operating temperature range) | VFB | 0.958 | 0.97 | 0.982 | V | VIN = 6V, ILOAD = 0.5A (l: full operating temperature range) | 3 |
| Feedback Voltage Line Regulation | | | 0.004 | 0.02 | %/V | VIN = 4V to 42V, ILOAD = 1A (l: full operating temperature range) | 3 |
| Feedback Pin Input Current | IFB | -20 | | 20 | nA | VFB = 1V | 3 |
| Minimum On-Time | tON(MIN) | 15 | 30 | 45 | ns | ILOAD = 1A, SYNC = 0V (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 180 | 210 | 240 | kHz | RT = 221k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 665 | 700 | 735 | kHz | RT = 60.4k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Oscillator Frequency | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1A (l: full operating temperature range) | 4 |
| Top Power NMOS Current Limit (LT8610A) | ILIM | 5 | 6.7 | 8 | A | LT8610A (l: full operating temperature range) | 4 |
| Bottom Power NMOS Current Limit | ILIM | 3.4 | 4.3 | 5.4 | A | VINTVCC = 3.4V | 4 |
| SW Leakage Current | ISW | -1.5 | | 1.5 | µA | VIN = 42V, VSW = 0V, 42V | 4 |
| INTVCC Undervoltage Lockout | VINTVCC(UVLO) | 2.5 | 2.6 | 2.7 | V | | 4 |
| EN/UV Pin Threshold | VEN/UV | 0.94 | 1 | 1.06 | V | EN/UV Rising (l: full operating temperature range) | 4 |
| EN/UV Pin Current | IEN/UV | -20 | | 20 | nA | VEN/UV = 2V | 4 |
| PG Upper Threshold Offset from VFB | | 6 | 9 | 12 | % | VFB Falling (l: full operating temperature range) | 4 |
| PG Lower Threshold Offset from VFB | | -12 | -9 | -6 | % | VFB Rising (l: full operating temperature range) | 4 |
| PG Leakage | IPG | -40 | | 40 | nA | VPG = 3.3V | 4 |
| SYNC Threshold (falling) | VSYNC | 0.8 | 1.1 | 1.4 | V | SYNC Falling | 4 |
| SYNC Threshold (rising) | VSYNC | 1.6 | 2 | 2.4 | V | SYNC Rising | 4 |
| SYNC Pin Current | ISYNC | -40 | | 40 | nA | VSYNC = 6V | 4 |
| TR/SS Source Current | ITR/SS | 1 | 2 | 3.2 | µA | (l: full operating temperature range) | 4 |
| Operating Junction Temperature Range (LT8610AE) | TJ | -40 | | 125 | °C | LT8610AE/LT8610ABE (Note 2) | 2 |
| VIN, EN/UV, PG Voltage | VIN | | | 42 | V | | 2 |
| BST Pin Above SW Pin | VBST-SW | | | 4 | V | | 2 |
| FB, TR/SS, RT, INTVCC Voltage | | | | 4 | V | | 2 |
| VOUT, SYNC Voltage | VOUT, VSYNC | | | 6 | V | | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Thermal Resistance, Junction to Ambient | θJA | | 40 | | °C/W | | 2 |
| Thermal Resistance, Junction to Exposed Pad | θJC(PAD) | | 10 | | °C/W | | 2 |
## CAD (KiCad official)
- Symbol: `LT8610AEMSE#TRPBF`
- Footprint: `Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm`
- 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lt8610aemse-trpbf-etched.step` / `lt8610aemse-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8610aemse-trpbf.step` / `lt8610aemse-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt8610a-8610ab.pdf) (26 pp, sha256 `b37433c4b3415525`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8610aemse-trpbf-datasheet.pdf)