main
Ray Publish 0.1.0 eaae0be

LT8610ACIMSE-1#PBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8610ACIMSE-1#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC input External clock synchronization input: ground for low-ripple Burst Mode at low loads, tie to a clock or a DC voltage of 3V or higher (or to INTVCC) for pulse-skipping mode, and do not float.
2 TR/SS bidirectional Output tracking and soft-start pin: below 0.8V it forces FB to follow TR/SS, an internal 2.2µA pull-up from INTVCC sets the startup ramp, it is pulled to ground through 230Ω in shutdown and fault, and at least 100pF must be used on the LT8610AC-1.
3 RT passive A resistor between RT and ground sets the switching frequency.
4 EN/UV input Shutdown enable: the part is off when low and active when high, with a rising threshold of 1.015V and falling threshold of 0.97V, and it should be tied to VIN if the shutdown feature is not used.
5 VIN power_in Supply pin for internal circuitry and the internal top-side power switch; it must be tied together with pin 6 and locally bypassed.
6 VIN power_in Supply pin for internal circuitry and the internal top-side power switch; it must be tied together with pin 5 and locally bypassed.
7 NC unconnected No connect: this pin is not connected to internal circuitry.
8 GND power_in Ground return for the internal bottom-side switch; it must be tied together with the exposed pad (pin 17) and kept close to the input capacitor negative terminal.
9 SW output Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB.
10 SW output Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB.
11 SW output Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB.
12 BST power_out Provides a drive voltage higher than VIN to the top-side power switch; place a 0.1µF boost capacitor as close as possible to the IC.
13 INTVCC power_out Internal 3.4V regulator bypass pin that supplies the internal drivers and control circuits; maximum output current is 20mA, it must not be loaded externally, and it needs at least 1µF low-ESR ceramic decoupling to power ground.
14 BIAS power_in When tied above 3.1V the internal regulator draws current from BIAS instead of VIN; for outputs of 3.3V and above tie it to VOUT, and if tied to another supply use a 1µF local bypass capacitor.
15 PG output Open-drain power-good output that stays low until FB is within ±8% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.0V regardless of EN/UV state.
16 FB input Feedback input that the part regulates to 0.800V: connect the feedback divider tap here and a 4.7pF to 10pF phase lead capacitor between FB and VOUT.
17 GND power_in Exposed pad ground that must be soldered to the PCB to lower the thermal resistance and is tied to the GND pins.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.6 3 V l: full operating temperature range 2
VIN Quiescent Current 1 3 µA VEN/UV = 0V 2
VIN Quiescent Current 1 8 µA VEN/UV = 0V; l: full operating temperature range 2
VIN Quiescent Current 1.7 4 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 2
VIN Quiescent Current 1.7 10 µA VEN/UV = 2V, Not Switching, VSYNC = 0V; l: full operating temperature range 2
VIN Quiescent Current 0.28 0.5 mA VEN/UV = 2V, Not Switching, VSYNC = 2V 2
VIN Current in Regulation 30 60 µA VOUT = 0.8V, VIN = 6V, Output Load = 100µA 3
VIN Current in Regulation 225 500 µA VOUT = 0.8V, VIN = 6V, Output Load = 1mA; l: full operating temperature range 3
Feedback Reference Voltage 0.794 0.8 0.806 V VIN = 6V, ILOAD = 0.5A 3
Feedback Reference Voltage 0.788 0.8 0.812 V VIN = 6V, ILOAD = 0.5A; l: full operating temperature range 3
Feedback Voltage Line Regulation 0.004 0.02 %/V VIN = 4.0V to 42V, ILOAD = 1A; l: full operating temperature range 3
Feedback Pin Input Current -20 20 nA VFB = 1V 3
INTVCC Voltage 3.23 3.25 3.4 V ILOAD = 0mA, VBIAS = 0V 3
INTVCC Voltage 3.29 3.35 3.57 V ILOAD = 0mA, VBIAS = 3.3V 3
INTVCC Undervoltage Lockout 2.37 2.47 2.57 V 3
Minimum On-Time 15 30 45 ns ILOAD = 1A, SYNC = 0V; l: full operating temperature range 3
Minimum Off-Time 95 125 ns 3
Oscillator Frequency 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 1A (LT8610AC/LT8610AC-1); l: full operating temperature range 3
Top Power NMOS Current Limit 5 6.7 8 A l: full operating temperature range 3
Bottom Power NMOS Current Limit 3.4 4.3 5.4 A VINTVCC = 3.4V 3
SW Leakage Current -1.5 1.5 µA VIN = 42V, VSW = 0V, 42V 3
EN/UV Pin Threshold 0.955 1.015 1.075 V EN/UV Rising; l: full operating temperature range 3
EN/UV Pin Current -20 20 nA VEN/UV = 2V 3
PG Upper Threshold Offset from VFB 5 8 11 % VFB Falling; l: full operating temperature range 3
PG Lower Threshold Offset from VFB -11 -8 -5 % VFB Rising; l: full operating temperature range 3
PG Leakage -40 40 nA VPG = 3.3V 3
PG Pull-Down Resistance 680 2000 Ω VPG = 0.1V; l: full operating temperature range 3
SYNC Threshold 0.8 1.1 1.4 V SYNC Falling 3
SYNC Threshold 1.6 2 2.4 V SYNC Rising 3
TR/SS Source Current 1 2 3.2 µA l: full operating temperature range 3
VIN, EN/UV, PG pin voltage 42 V 2
BIAS pin voltage 30 V 2
BST Pin Above SW Pin 4 V 2
FB, TR/SS, RT, INTVCC voltage 4 V 2
SYNC Voltage 6 V 2
Operating Junction Temperature Range (LT8610ACI/LT8610ACI-1) -40 125 °C 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W 2
Thermal Resistance Junction-to-Case (Exposed Pad) θJC(PAD) 10 °C/W 2
BIAS Pin Current Consumption 9.2 mA VBIAS = 3.3V, ILOAD = 1A, 2MHz 3
Top Power NMOS On-Resistance 120 mΩ ISW = 1A 3
Bottom Power NMOS On-Resistance 65 mΩ VINTVCC = 3.4V, ISW = 1A 3
EN/UV Pin Hysteresis 50 mV 3
PG Hysteresis 0.4 % 3
TR/SS Pull-Down Resistance 230 Ω Fault Condition, TR/SS = 0.1V 3

CAD (KiCad official)

  • Symbol: LT8610ACIMSE-1#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8610acimse-1-pbf-etched.step / lt8610acimse-1-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8610acimse-1-pbf.step / lt8610acimse-1-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 dd42b6a8e79c0863, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF