Generated by kicad-footprint-generator · KiCad file format 20260206
LT8610ACIMSE-1#PBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8610ACIMSE-1#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input: ground for low-ripple Burst Mode at low loads, tie to a clock or a DC voltage of 3V or higher (or to INTVCC) for pulse-skipping mode, and do not float. |
| 2 | TR/SS | bidirectional | Output tracking and soft-start pin: below 0.8V it forces FB to follow TR/SS, an internal 2.2µA pull-up from INTVCC sets the startup ramp, it is pulled to ground through 230Ω in shutdown and fault, and at least 100pF must be used on the LT8610AC-1. |
| 3 | RT | passive | A resistor between RT and ground sets the switching frequency. |
| 4 | EN/UV | input | Shutdown enable: the part is off when low and active when high, with a rising threshold of 1.015V and falling threshold of 0.97V, and it should be tied to VIN if the shutdown feature is not used. |
| 5 | VIN | power_in | Supply pin for internal circuitry and the internal top-side power switch; it must be tied together with pin 6 and locally bypassed. |
| 6 | VIN | power_in | Supply pin for internal circuitry and the internal top-side power switch; it must be tied together with pin 5 and locally bypassed. |
| 7 | NC | unconnected | No connect: this pin is not connected to internal circuitry. |
| 8 | GND | power_in | Ground return for the internal bottom-side switch; it must be tied together with the exposed pad (pin 17) and kept close to the input capacitor negative terminal. |
| 9 | SW | output | Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB. |
| 10 | SW | output | Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB. |
| 11 | SW | output | Output of the internal power switches; tie SW pins 9, 10 and 11 together, connect them to the inductor and boost capacitor, and keep the node small on the PCB. |
| 12 | BST | power_out | Provides a drive voltage higher than VIN to the top-side power switch; place a 0.1µF boost capacitor as close as possible to the IC. |
| 13 | INTVCC | power_out | Internal 3.4V regulator bypass pin that supplies the internal drivers and control circuits; maximum output current is 20mA, it must not be loaded externally, and it needs at least 1µF low-ESR ceramic decoupling to power ground. |
| 14 | BIAS | power_in | When tied above 3.1V the internal regulator draws current from BIAS instead of VIN; for outputs of 3.3V and above tie it to VOUT, and if tied to another supply use a 1µF local bypass capacitor. |
| 15 | PG | output | Open-drain power-good output that stays low until FB is within ±8% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.0V regardless of EN/UV state. |
| 16 | FB | input | Feedback input that the part regulates to 0.800V: connect the feedback divider tap here and a 4.7pF to 10pF phase lead capacitor between FB and VOUT. |
| 17 | GND | power_in | Exposed pad ground that must be soldered to the PCB to lower the thermal resistance and is tied to the GND pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.6 | 3 | V | l: full operating temperature range | 2 | ||
| VIN Quiescent Current | 1 | 3 | µA | VEN/UV = 0V | 2 | ||
| VIN Quiescent Current | 1 | 8 | µA | VEN/UV = 0V; l: full operating temperature range | 2 | ||
| VIN Quiescent Current | 1.7 | 4 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 2 | ||
| VIN Quiescent Current | 1.7 | 10 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V; l: full operating temperature range | 2 | ||
| VIN Quiescent Current | 0.28 | 0.5 | mA | VEN/UV = 2V, Not Switching, VSYNC = 2V | 2 | ||
| VIN Current in Regulation | 30 | 60 | µA | VOUT = 0.8V, VIN = 6V, Output Load = 100µA | 3 | ||
| VIN Current in Regulation | 225 | 500 | µA | VOUT = 0.8V, VIN = 6V, Output Load = 1mA; l: full operating temperature range | 3 | ||
| Feedback Reference Voltage | 0.794 | 0.8 | 0.806 | V | VIN = 6V, ILOAD = 0.5A | 3 | |
| Feedback Reference Voltage | 0.788 | 0.8 | 0.812 | V | VIN = 6V, ILOAD = 0.5A; l: full operating temperature range | 3 | |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4.0V to 42V, ILOAD = 1A; l: full operating temperature range | 3 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1V | 3 | ||
| INTVCC Voltage | 3.23 | 3.25 | 3.4 | V | ILOAD = 0mA, VBIAS = 0V | 3 | |
| INTVCC Voltage | 3.29 | 3.35 | 3.57 | V | ILOAD = 0mA, VBIAS = 3.3V | 3 | |
| INTVCC Undervoltage Lockout | 2.37 | 2.47 | 2.57 | V | 3 | ||
| Minimum On-Time | 15 | 30 | 45 | ns | ILOAD = 1A, SYNC = 0V; l: full operating temperature range | 3 | |
| Minimum Off-Time | 95 | 125 | ns | 3 | |||
| Oscillator Frequency | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1A (LT8610AC/LT8610AC-1); l: full operating temperature range | 3 | |
| Top Power NMOS Current Limit | 5 | 6.7 | 8 | A | l: full operating temperature range | 3 | |
| Bottom Power NMOS Current Limit | 3.4 | 4.3 | 5.4 | A | VINTVCC = 3.4V | 3 | |
| SW Leakage Current | -1.5 | 1.5 | µA | VIN = 42V, VSW = 0V, 42V | 3 | ||
| EN/UV Pin Threshold | 0.955 | 1.015 | 1.075 | V | EN/UV Rising; l: full operating temperature range | 3 | |
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 3 | ||
| PG Upper Threshold Offset from VFB | 5 | 8 | 11 | % | VFB Falling; l: full operating temperature range | 3 | |
| PG Lower Threshold Offset from VFB | -11 | -8 | -5 | % | VFB Rising; l: full operating temperature range | 3 | |
| PG Leakage | -40 | 40 | nA | VPG = 3.3V | 3 | ||
| PG Pull-Down Resistance | 680 | 2000 | Ω | VPG = 0.1V; l: full operating temperature range | 3 | ||
| SYNC Threshold | 0.8 | 1.1 | 1.4 | V | SYNC Falling | 3 | |
| SYNC Threshold | 1.6 | 2 | 2.4 | V | SYNC Rising | 3 | |
| TR/SS Source Current | 1 | 2 | 3.2 | µA | l: full operating temperature range | 3 | |
| VIN, EN/UV, PG pin voltage | 42 | V | 2 | ||||
| BIAS pin voltage | 30 | V | 2 | ||||
| BST Pin Above SW Pin | 4 | V | 2 | ||||
| FB, TR/SS, RT, INTVCC voltage | 4 | V | 2 | ||||
| SYNC Voltage | 6 | V | 2 | ||||
| Operating Junction Temperature Range (LT8610ACI/LT8610ACI-1) | -40 | 125 | °C | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | 2 | |||
| Thermal Resistance Junction-to-Case (Exposed Pad) | θJC(PAD) | 10 | °C/W | 2 | |||
| BIAS Pin Current Consumption | 9.2 | mA | VBIAS = 3.3V, ILOAD = 1A, 2MHz | 3 | |||
| Top Power NMOS On-Resistance | 120 | mΩ | ISW = 1A | 3 | |||
| Bottom Power NMOS On-Resistance | 65 | mΩ | VINTVCC = 3.4V, ISW = 1A | 3 | |||
| EN/UV Pin Hysteresis | 50 | mV | 3 | ||||
| PG Hysteresis | 0.4 | % | 3 | ||||
| TR/SS Pull-Down Resistance | 230 | Ω | Fault Condition, TR/SS = 0.1V | 3 |
CAD (KiCad official)
- Symbol:
LT8610ACIMSE-1#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8610acimse-1-pbf-etched.step/lt8610acimse-1-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8610acimse-1-pbf.step/lt8610acimse-1-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
dd42b6a8e79c0863, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).