Generated by kicad-footprint-generator · KiCad file format 20260206
LT8609BEMSE#PBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT8609BEMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides a drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC with no series resistor. |
| 2 | SW | output | Output of the internal power switches; connect to the inductor and boost capacitor and keep the node small on the PCB. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin (max output current 20mA, varies 2.8V to 3.5V); decouple with at least a 1µF low ESR ceramic capacitor and do not load with external circuitry. |
| 4 | RT | passive | A resistor tied between RT and ground sets the switching frequency. |
| 5 | NC | unconnected | On the LT8609B the SYNC pin is replaced with a no connect; the LT8609B operates in pulse-skipping mode without spread spectrum. |
| 6 | FB | input | Regulates to 0.782V; connect the feedback resistor divider tap to this pin. |
| 7 | TR/SS | input | Output tracking and soft-start pin; a voltage below 0.782V forces FB to equal it, an internal 2µA pull-up allows a capacitor to set the ramp rate, and it is pulled to ground with a 300Ω MOSFET during shutdown and faults. |
| 8 | PG | output | Open-drain output of an internal comparator that stays low until FB is within ±8.5% of final regulation voltage and there are no faults; valid when VIN is above 3.2V regardless of EN/UV state. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and topside power switch; must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins. |
| 10 | EN/UV | input | Part is shut down when low and active when high, with hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if shutdown is unused, or use a resistor divider from VIN to program a UVLO threshold. |
| 11 | GND | power_in | Exposed pad (pin 11) must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| FB, TR/SS voltage | 4 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Junction Temperature Range | -40 | 125 | °C | LT8609BE | 2 | ||
| Junction-to-ambient thermal resistance | θJA | 40 | °C/W | MSE package, 10-lead MSOP | 2 | ||
| Minimum Input Voltage | 2.7 | 3.2 | V | over full operating temperature range; printed values 2.7, 3.0, 3.2 | 4 | ||
| VIN Quiescent Current (shutdown) | IQ | 1 | 4 | µA | LT8609B: VEN/UV = 0V | 4 | |
| VIN Quiescent Current (not switching) | IQ | 350 | µA | LT8609B: VEN/UV = 2V, Not Switching | 4 | ||
| Feedback Reference Voltage | VFB | 0.772 | 0.782 | 0.792 | V | LT8609B: VIN = 6V, ILOAD = 100mA | 4 |
| Feedback Reference Voltage (full temp) | VFB | 0.759 | 0.782 | 0.805 | V | LT8609B: VIN = 6V, ILOAD = 100mA, over full operating temperature range | 4 |
| Feedback Voltage Line Regulation | 0.004 | 0.04 | %/V | LT8609B: VIN = 4.0V to 40V | 4 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1.0V | 4 | ||
| Minimum On-Time | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V | 4 | ||
| Minimum Off Time | 90 | 130 | ns | 4 | |||
| Oscillator Frequency | 1.875 | 2 | 2.125 | MHz | LT8609B: RT = 18.2k, ILOAD = 0.5A | 5 | |
| Top Power NMOS On-Resistance | 185 | mΩ | ILOAD = 1A | 5 | |||
| Top Power NMOS Current Limit | 3.4 | 4.5 | 5.7 | A | 5 | ||
| Bottom Power NMOS On-Resistance | 115 | mΩ | 5 | ||||
| SW Leakage Current | 15 | µA | VIN = 42V, VSW = 40V | 5 | |||
| EN/UV Pin Threshold | 0.99 | 1.05 | 1.11 | V | EN/UV Rising | 5 | |
| EN/UV Pin Hysteresis | 50 | mV | 5 | ||||
| EN/UV Pin Current | -30 | 30 | nA | LT8609B: VEN/UV = 2V | 5 | ||
| PG Upper Threshold Offset from VFB | 4 | 8.5 | 14 | % | LT8609B: VFB Rising | 5 | |
| PG Lower Threshold Offset from VFB | 4 | 8.5 | 14 | % | LT8609B: VFB Falling | 5 | |
| PG Hysteresis | 0.5 | % | 5 | ||||
| PG Leakage | -200 | 200 | nA | VPG = 42V | 5 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 5 | ||
| TR/SS Source Current | 1 | 2 | 3 | µA | 5 | ||
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 |
CAD (KiCad official)
- Symbol:
LT8609BEMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt8609bemse-pbf-etched.step/lt8609bemse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8609bemse-pbf.step/lt8609bemse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
bb514bf594e97238, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).