Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8609BEMSE#PBF

Analog Devices · DC-DC Converters · MSOP-10-EP

LT8609BEMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST passive Provides a drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC with no series resistor.
2 SW output Output of the internal power switches; connect to the inductor and boost capacitor and keep the node small on the PCB.
3 INTVCC power_out Internal 3.5V regulator bypass pin (max output current 20mA, varies 2.8V to 3.5V); decouple with at least a 1µF low ESR ceramic capacitor and do not load with external circuitry.
4 RT passive A resistor tied between RT and ground sets the switching frequency.
5 NC unconnected On the LT8609B the SYNC pin is replaced with a no connect; the LT8609B operates in pulse-skipping mode without spread spectrum.
6 FB input Regulates to 0.782V; connect the feedback resistor divider tap to this pin.
7 TR/SS input Output tracking and soft-start pin; a voltage below 0.782V forces FB to equal it, an internal 2µA pull-up allows a capacitor to set the ramp rate, and it is pulled to ground with a 300Ω MOSFET during shutdown and faults.
8 PG output Open-drain output of an internal comparator that stays low until FB is within ±8.5% of final regulation voltage and there are no faults; valid when VIN is above 3.2V regardless of EN/UV state.
9 VIN power_in Supplies current to the internal circuitry and topside power switch; must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins.
10 EN/UV input Part is shut down when low and active when high, with hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if shutdown is unused, or use a resistor divider from VIN to program a UVLO threshold.
11 GND power_in Exposed pad (pin 11) must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10-EP
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
FB, TR/SS voltage 4 V 2
Storage Temperature Range -65 150 °C 2
Operating Junction Temperature Range -40 125 °C LT8609BE 2
Junction-to-ambient thermal resistance θJA 40 °C/W MSE package, 10-lead MSOP 2
Minimum Input Voltage 2.7 3.2 V over full operating temperature range; printed values 2.7, 3.0, 3.2 4
VIN Quiescent Current (shutdown) IQ 1 4 µA LT8609B: VEN/UV = 0V 4
VIN Quiescent Current (not switching) IQ 350 µA LT8609B: VEN/UV = 2V, Not Switching 4
Feedback Reference Voltage VFB 0.772 0.782 0.792 V LT8609B: VIN = 6V, ILOAD = 100mA 4
Feedback Reference Voltage (full temp) VFB 0.759 0.782 0.805 V LT8609B: VIN = 6V, ILOAD = 100mA, over full operating temperature range 4
Feedback Voltage Line Regulation 0.004 0.04 %/V LT8609B: VIN = 4.0V to 40V 4
Feedback Pin Input Current -20 20 nA VFB = 1.0V 4
Minimum On-Time 45 75 ns ILOAD = 1.5A, SYNC = 0V 4
Minimum Off Time 90 130 ns 4
Oscillator Frequency 1.875 2 2.125 MHz LT8609B: RT = 18.2k, ILOAD = 0.5A 5
Top Power NMOS On-Resistance 185 mΩ ILOAD = 1A 5
Top Power NMOS Current Limit 3.4 4.5 5.7 A 5
Bottom Power NMOS On-Resistance 115 mΩ 5
SW Leakage Current 15 µA VIN = 42V, VSW = 40V 5
EN/UV Pin Threshold 0.99 1.05 1.11 V EN/UV Rising 5
EN/UV Pin Hysteresis 50 mV 5
EN/UV Pin Current -30 30 nA LT8609B: VEN/UV = 2V 5
PG Upper Threshold Offset from VFB 4 8.5 14 % LT8609B: VFB Rising 5
PG Lower Threshold Offset from VFB 4 8.5 14 % LT8609B: VFB Falling 5
PG Hysteresis 0.5 % 5
PG Leakage -200 200 nA VPG = 42V 5
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 5
TR/SS Source Current 1 2 3 µA 5
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, TR/SS = 0.1V 5

CAD (KiCad official)

  • Symbol: LT8609BEMSE#PBF
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lt8609bemse-pbf-etched.step / lt8609bemse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8609bemse-pbf.step / lt8609bemse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 bb514bf594e97238, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF