main
Ray
Publish 0.1.0
a9cd51c
LT8607IDC#TRMPBF
Analog Devices · DC-DC Converters · DFN-8-EP(2x2)
LT8607IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides a drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series. |
| 2 | SW | power_out | Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin (2.8V to 3.5V, 20mA max output current) that powers the internal drivers and control circuits; decouple with at least 1µF low ESR ceramic capacitor and do not load externally. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency, which is 200kHz to 2.2MHz adjustable. |
| 5 | FB | input | The LT8607 regulates this pin to 0.778V; connect the feedback resistor divider tap here. |
| 6 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of the final regulation voltage and there are no faults; valid when VIN is above 3.2V and EN/UV is high. |
| 7 | VIN | power_in | Supplies current to the internal circuitry and the topside power switch (3.0V to 42V operating input, 42V absolute maximum); must be locally bypassed with the input capacitor placed close to the pin. |
| 8 | EN/UV | input | Shuts the part down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused or use a divider from VIN to program undervoltage lockout (42V absolute maximum). |
| 9 | GND | power_in | Exposed pad (pin 9) ground; must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.5 | 3 | 3.2 | V | 3 | ||
| Feedback Reference Voltage DFN Package | VFB | 0.771 | 0.778 | 0.785 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage DFN Package over full temperature range | VFB | 0.753 | 0.778 | 0.803 | V | VIN = 6V, ILOAD = 100mA, full operating temperature range | 3 |
| VIN Current in Regulation | IIN | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 3 | |
| VIN Current in Regulation | IIN | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 3 | |
| Feedback Voltage Line Regulation | 0.02 | 0.04 | %/V | VIN = 4.0V to 40V, full operating temperature range | 3 | ||
| Feedback Pin Input Current | IFB | -20 | 20 | nA | VFB = 1.0V, full operating temperature range | 4 | |
| Minimum On-Time | tON(MIN) | 35 | 65 | ns | ILOAD = 500mA, SYNC = 0V or LT8607 DFN | 4 | |
| Minimum Off Time | tOFF(MIN) | 93 | 130 | ns | ILOAD = 300mA | 4 | |
| Oscillator Frequency DFN Package | fSW | 140 | 200 | 260 | kHz | RT = 221k, ILOAD = 350mA | 4 |
| Oscillator Frequency DFN Package | fSW | 610 | 700 | 790 | kHz | RT = 60.4k, ILOAD = 350mA | 4 |
| Oscillator Frequency DFN Package | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 350mA | 4 |
| Top Power NMOS Current Limit DFN Package | ILIM | 1.2 | 1.7 | 2.2 | A | 4 | |
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising, full operating temperature range | 4 |
| EN/UV Pin Current | IEN/UV | -20 | 20 | nA | VEN/UV = 2V | 4 | |
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising, full operating temperature range | 4 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling, full operating temperature range | 4 | |
| PG Leakage | IPG | -200 | 200 | nA | VPG = 42V | 4 | |
| PG Pull-Down Resistance | RPG | 550 | 1200 | Ω | VPG = 0.1V | 4 | |
| FB Absolute Maximum Voltage | FB | 4 | V | 2 | |||
| Operating Junction Temperature Range (LT8607I) | TJ | -40 | 125 | °C | LT8607I | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient (DC8 DFN package) | θJA | 102 | °C/W | 8-Lead DFN package | 2 |
CAD (KiCad official)
- Symbol:
LT8607IDC#TRMPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt8607idc-trmpbf-etched.step/lt8607idc-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8607idc-trmpbf.step/lt8607idc-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
3023cd9406e13917, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8607IDC#TRMPBF
**Analog Devices** · DC-DC Converters · DFN-8-EP(2x2)
LT8607IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides a drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series. |
| 2 | SW | power_out | Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin (2.8V to 3.5V, 20mA max output current) that powers the internal drivers and control circuits; decouple with at least 1µF low ESR ceramic capacitor and do not load externally. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency, which is 200kHz to 2.2MHz adjustable. |
| 5 | FB | input | The LT8607 regulates this pin to 0.778V; connect the feedback resistor divider tap here. |
| 6 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of the final regulation voltage and there are no faults; valid when VIN is above 3.2V and EN/UV is high. |
| 7 | VIN | power_in | Supplies current to the internal circuitry and the topside power switch (3.0V to 42V operating input, 42V absolute maximum); must be locally bypassed with the input capacitor placed close to the pin. |
| 8 | EN/UV | input | Shuts the part down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused or use a divider from VIN to program undervoltage lockout (42V absolute maximum). |
| 9 | GND | power_in | Exposed pad (pin 9) ground; must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | | 2.5 | 3 | 3.2 | V | | 3 |
| Feedback Reference Voltage DFN Package | VFB | 0.771 | 0.778 | 0.785 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage DFN Package over full temperature range | VFB | 0.753 | 0.778 | 0.803 | V | VIN = 6V, ILOAD = 100mA, full operating temperature range | 3 |
| VIN Current in Regulation | IIN | | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 3 |
| VIN Current in Regulation | IIN | | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 3 |
| Feedback Voltage Line Regulation | | | 0.02 | 0.04 | %/V | VIN = 4.0V to 40V, full operating temperature range | 3 |
| Feedback Pin Input Current | IFB | -20 | | 20 | nA | VFB = 1.0V, full operating temperature range | 4 |
| Minimum On-Time | tON(MIN) | 35 | | 65 | ns | ILOAD = 500mA, SYNC = 0V or LT8607 DFN | 4 |
| Minimum Off Time | tOFF(MIN) | | 93 | 130 | ns | ILOAD = 300mA | 4 |
| Oscillator Frequency DFN Package | fSW | 140 | 200 | 260 | kHz | RT = 221k, ILOAD = 350mA | 4 |
| Oscillator Frequency DFN Package | fSW | 610 | 700 | 790 | kHz | RT = 60.4k, ILOAD = 350mA | 4 |
| Oscillator Frequency DFN Package | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 350mA | 4 |
| Top Power NMOS Current Limit DFN Package | ILIM | 1.2 | 1.7 | 2.2 | A | | 4 |
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising, full operating temperature range | 4 |
| EN/UV Pin Current | IEN/UV | -20 | | 20 | nA | VEN/UV = 2V | 4 |
| PG Upper Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Rising, full operating temperature range | 4 |
| PG Lower Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Falling, full operating temperature range | 4 |
| PG Leakage | IPG | -200 | | 200 | nA | VPG = 42V | 4 |
| PG Pull-Down Resistance | RPG | | 550 | 1200 | Ω | VPG = 0.1V | 4 |
| FB Absolute Maximum Voltage | FB | | | 4 | V | | 2 |
| Operating Junction Temperature Range (LT8607I) | TJ | -40 | | 125 | °C | LT8607I | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction-to-Ambient (DC8 DFN package) | θJA | | 102 | | °C/W | 8-Lead DFN package | 2 |
## CAD (KiCad official)
- Symbol: `LT8607IDC#TRMPBF`
- Footprint: `Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm`
- 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `lt8607idc-trmpbf-etched.step` / `lt8607idc-trmpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8607idc-trmpbf.step` / `lt8607idc-trmpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt8607-8607b.pdf) (24 pp, sha256 `3023cd9406e13917`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8607idc-trmpbf-datasheet.pdf)