Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8607IDC#TRMPBF

Analog Devices · DC-DC Converters · DFN-8-EP(2x2)

LT8607IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST passive Provides a drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series.
2 SW power_out Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB.
3 INTVCC power_out Internal 3.5V regulator bypass pin (2.8V to 3.5V, 20mA max output current) that powers the internal drivers and control circuits; decouple with at least 1µF low ESR ceramic capacitor and do not load externally.
4 RT passive A resistor from RT to ground sets the switching frequency, which is 200kHz to 2.2MHz adjustable.
5 FB input The LT8607 regulates this pin to 0.778V; connect the feedback resistor divider tap here.
6 PG output Open-drain power-good output that stays low until FB is within ±8.5% of the final regulation voltage and there are no faults; valid when VIN is above 3.2V and EN/UV is high.
7 VIN power_in Supplies current to the internal circuitry and the topside power switch (3.0V to 42V operating input, 42V absolute maximum); must be locally bypassed with the input capacitor placed close to the pin.
8 EN/UV input Shuts the part down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused or use a divider from VIN to program undervoltage lockout (42V absolute maximum).
9 GND power_in Exposed pad (pin 9) ground; must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-8-EP(2x2)
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.5 3 3.2 V 3
Feedback Reference Voltage DFN Package VFB 0.771 0.778 0.785 V VIN = 6V, ILOAD = 100mA 3
Feedback Reference Voltage DFN Package over full temperature range VFB 0.753 0.778 0.803 V VIN = 6V, ILOAD = 100mA, full operating temperature range 3
VIN Current in Regulation IIN 56 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100µA 3
VIN Current in Regulation IIN 500 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA 3
Feedback Voltage Line Regulation 0.02 0.04 %/V VIN = 4.0V to 40V, full operating temperature range 3
Feedback Pin Input Current IFB -20 20 nA VFB = 1.0V, full operating temperature range 4
Minimum On-Time tON(MIN) 35 65 ns ILOAD = 500mA, SYNC = 0V or LT8607 DFN 4
Minimum Off Time tOFF(MIN) 93 130 ns ILOAD = 300mA 4
Oscillator Frequency DFN Package fSW 140 200 260 kHz RT = 221k, ILOAD = 350mA 4
Oscillator Frequency DFN Package fSW 610 700 790 kHz RT = 60.4k, ILOAD = 350mA 4
Oscillator Frequency DFN Package fSW 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 350mA 4
Top Power NMOS Current Limit DFN Package ILIM 1.2 1.7 2.2 A 4
EN/UV Pin Threshold VEN/UV 0.99 1.05 1.11 V EN/UV Rising, full operating temperature range 4
EN/UV Pin Current IEN/UV -20 20 nA VEN/UV = 2V 4
PG Upper Threshold Offset from VFB 5 8.5 13 % VFB Rising, full operating temperature range 4
PG Lower Threshold Offset from VFB 5 8.5 13 % VFB Falling, full operating temperature range 4
PG Leakage IPG -200 200 nA VPG = 42V 4
PG Pull-Down Resistance RPG 550 1200 Ω VPG = 0.1V 4
FB Absolute Maximum Voltage FB 4 V 2
Operating Junction Temperature Range (LT8607I) TJ -40 125 °C LT8607I 2
Storage Temperature Range TSTG -65 150 °C 2
Thermal Resistance Junction-to-Ambient (DC8 DFN package) θJA 102 °C/W 8-Lead DFN package 2

CAD (KiCad official)

  • Symbol: LT8607IDC#TRMPBF
  • Footprint: Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm
  • 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: lt8607idc-trmpbf-etched.step / lt8607idc-trmpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8607idc-trmpbf.step / lt8607idc-trmpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 3023cd9406e13917, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF